Production Safety Responsibility Letter of Supervision Unit

Supervisory Unit Safety Production Responsibility Letter

In the era of continuous progress, the number of occasions when people use responsibility letters is increasing. Responsibility letters can better clarify the tasks we should undertake. It helps us accomplish the mission we should accomplish. I am sure that most people have a headache in drafting a responsibility letter. The following is the safety production responsibility letter of the supervision unit that I compiled. I hope it will be helpful to everyone.

Supervision Unit Safety Production Responsibility Letter 1

In order to strengthen coal mine safety management, we must adhere to the people-oriented policy of "safety first, prevention first". Achieve the safety management goals issued by superior authorities and other departments, complete various safety production indicators, and formulate the "Safety Management Regulations" in accordance with the "Coal Law", "Safety Regulations", "Special Provisions", "Shanxi Province Coal Management Regulations" and other relevant requirements Statement of Responsibility for Management by Objectives.

1. Safety production goals

1. Control indicators within the jurisdiction: "0 people" in serious injury accidents and "0 people" in fatal accidents "0" in minor injury accidents.

2. Ensure the normal operation of the monitoring and control center.

3. Ensure that the calibration room calibrates various instruments and meters according to the prescribed time.

4. Ensure that all transmission lines are unobstructed and maintain them in a timely manner if there is a fault.

5. Ensure that the monitoring probes and sub-station hanging positions are reasonable and the display is accurate.

2. Scope of Responsibilities

1. Responsible for the personnel positioning of sub-stations and transmission lines and the maintenance of transmission lines at the track downhill.

2. Return air down the mountain is responsible for the maintenance of gas sensors, wind speed sensors, and transmission lines.

3. The 9203 mining working face is responsible for the maintenance of sub-stations, gas sensors, transmission lines, and local fan start and stop sensors.

4. The excavation working face in the mining area is responsible for the maintenance of sub-stations, gas sensors and transmission lines.

5. The fan room is responsible for substations, gas sensors, negative pressure sensors, damper sensors, and wind speed sensors.

6. The main inclined shaft is responsible for the maintenance of the main transmission line.

7. The monitoring center is responsible for the installation, debugging, maintenance and management of the monitoring system.

8. The calibration room is responsible for the maintenance, calibration, calibration, dressing change and other management of instruments such as alarm miner's lamps, optical methane tile detectors, portable tile detectors and other instruments.

9. Responsible for the installation and maintenance of various underground sensors.

3. Management content and technical requirements

The director of the monitoring center, under the leadership of the deputy technical director, is responsible for the work of the entire mine as follows:

1. Monitoring Management of the center

2. Management of the calibration room

3. Management of various sensors and line maintenance

4. Calibration of miner’s lamps and lamp rooms Management

Technical requirements:

The management of the monitoring and control center is implemented and managed in strict accordance with the "Coal Mine Safety Regulations" and the requirements for ventilation safety and quality standardization safety monitoring.

(1) Monitoring and monitoring technology management

1. Inspection workers are responsible for the installation, maintenance, debugging, repair and management of the upper and lower monitoring and control systems in the mine to ensure that signals Accurate and unobstructed.

2. The calibrator is responsible for the maintenance, calibration, dressing change and other management work of all mine-wide alarm miner's lamps, gas detectors, portable tile inspection instruments, etc. to ensure the normal use of the instruments.

3. Keep abreast of the dynamic conditions of various mining working faces at any time, prepare the new underground working face in advance for monitoring and monitoring, and closely cooperate with production.

4. Coordinate the ventilation department to coordinate the air volume for coal mining and excavation, and master the management of working surface tiles, air volume, wind speed, and damper sensors.

5. Responsible for providing the supply department with required spare parts, materials, and other plans for emergency use, and maintaining 100% reserve.

6. Go deep underground to check the working status of the monitoring system route and the position of the probe to ensure the normal operation of each system.

7. Conduct patrol inspections of all operating points above and below the well, and report any problems to superiors.

8. Complete the tasks assigned by the leadership and conscientiously implement the "three major regulations" and the instructions from superiors on "one communication and three defenses".

(2) Equipment and facility management

1. The monitoring and control device must be powered on for 48 hours before entering the well according to the requirements of the product manual, and can only be put into the well after passing the debugging. Install.

2. After installation in the well, various indicators must be debugged before operation. It can be used only after it is qualified. If the downhole debugging fails, it must be replaced immediately or inspected in the well.

3. The electrical equipment, power lines and control lines associated with the testing equipment are maintained by designated personnel from the electromechanical team. When changing or dismantling the lines, they must contact the relevant departments in advance and communicate with the inspection personnel on site. Same processing.

4. When the electrical equipment of the fault maintenance and safety maintenance equipment needs to be stopped for monitoring, safety measures must be formulated with the consent of the technical mine director and reported to the county bureau before implementation.

5. When the gas probe is impacted by a high concentration of gas, it must be calibrated and recorded.

6. Various devices have been running continuously underground for 6 months and must be lifted up for maintenance.

7. The underground equipment must be maintained and debugged regularly. Standard gas samples and air samples should be used to calibrate and debug the sensors every 7 days. After debugging, the debugging and maintenance records must be carefully filled in.

8. You must be responsible for the calibration work and perform regular calibrations. All instruments and sensors are required to be sensitive, reliable and accurate. The alarm point must be powered off and restored, and the concentration must be accurate. The installation locations of the probes at each location must comply with regulations, and various records must be made.

IV. Implementation of responsibilities

1. Determine the basic salary based on the safety production tasks and safety indicators assigned by superiors, and determine the efficiency salary based on the number of times, time and work efficiency of going down the mine. Safety wages are determined based on the achievement of safety indicators. Based on the quality standardized assessment scores, the standard salary is determined.

2. Strictly implement the “2009 Safety Management Implementation Plan of Our Mine”.

3. Illegal operations, illegal command, and violation of labor disciplines shall be implemented in accordance with the "Safety Management Penalty Regulations".

Xiasitou Coal Mining Co., Ltd.

Xiasitou Coal Mining Co., Ltd.

Xiasitou Coal Mining Co., Ltd.

Safety production target management Letter of Responsibility

Director of the Monitoring Center:

Worker: Supervision Unit Safety Production Responsibility Letter 2

Party A: xxx Co., Ltd. (hereinafter referred to as Party A)

Party B: The Project Supervision Department of the Longyan Financial and Business Center Phase I Lot B Project Department (hereinafter referred to as Party B), in order to effectively implement the work policy of "safety first, prevention first", achieve safe production without accidents, and ensure To ensure the smooth progress of project construction, ensure the personal and financial safety of project construction personnel, and maintain the company's social reputation and economic interests, Party A and Party B have specially formulated this letter of responsibility.

1. Responsibility objectives

(1) Safety production

1. Strictly implement the "Construction Project Safety Management Regulations" and "Construction Safety Inspection Standards" 》and national laws, regulations and norms related to production safety.

2. Establish and improve various safety production supervision rules and operating procedures at the construction site; fully implement the company's various safety production rules and regulations.

3. Prevent deaths, major accidents and other major liability accidents, and control the minor injury accident rate within 2%.

4. Prevent accidents such as object strikes, falling from high altitude, collapse, vehicle damage, machinery damage, electric shock, drowning, fire, explosion, poisoning and other accidents.

5. The rectification of hidden accident hazards must be carried out with strict personnel, time and measures, and the rectification rate should reach 100%.

6. The pre-job safety education and training rate for new employees and migrant workers reaches 100%.

7. Safety inspection: Party A’s quality and safety department shall organize inspections of each unit (or project department) no less than once a month; safety self-inspections of each contracting team shall be no less than 4 times a month ;The work team should insist on daily inspections.

8. There are no cases in which employees have violated laws and disciplines and been subject to judicial sanctions.

(2) Civilized construction

1. Corporate image and logo layout. Logo boards should be hung on the outer construction frames of buildings facing the street. The format and size of billboards are uniformly stipulated by the Marketing Planning Department.

2. Basic Standards for Safety and Civilization Safety and civilization at construction sites should refer to the "Construction Safety Inspection Standards" jgj59-XX and the local construction authorities. Regarding the construction of walls and gates, the requirements of the local government authorities must be met, and approval must be submitted in accordance with the bidding management regulations.

3. The five signs and one picture project signs include the general construction layout plan, project overview sign, civilized construction sign, management personnel sign, safety production sign, and fire protection sign. The project overview board is placed in a conspicuous position on the construction site fence, indicating the project name, scale, start and completion date, construction license number, construction unit, design unit, quality and safety supervision unit, construction unit, supervision unit and contact number, etc. . If there are major hazard sources at the construction site, "public notice boards" should also be hung in conspicuous locations.

4. During the main construction stage of the scaffolding, the outer frame should be closed. The height of the fence should not be less than

1.5 meters above the working surface. Single projects that are not closed in place are not allowed to enter the next process. construction. The construction fence steel pipes must be marked with red or white (or black or yellow) paint, and the safety net must use a qualified dense-mesh safety net. The construction fence should be strong, safe, beautiful, and standardized, and should be cleaned regularly. Damaged safety nets must be replaced promptly. The outer enclosed frame must have banners and slogans, indicating the construction building number, floor number, quality, safety and civilized construction slogans.

5. The process connections are reasonable and the handover responsibilities are clear.

6. Establish strict protection measures for finished products and all materials, components, and semi-finished products should be stacked neatly according to the site layout plan. The construction site should be flat and the roads should be smooth.

7. Implement cleaning and maintenance management measures for the passages within the project scope to ensure that they are smooth, smooth and free of pits and ponds.

8. Strengthen on-site construction management, ensure that each process is done with clean hands, speed up the construction progress, and ensure that the site is clean when the work is completed

No tail is left.

2. Responsibility measures

1. Conscientiously implement the safety production policy and accept the safety production supervision and guidance of Party A’s safety department.

2. Before project construction operations, employees must be educated on necessary safety protection knowledge, implement safety technical briefings, and enhance employees’ awareness of production safety and self-protection awareness.

3. Special types of work must be held with certificates, and illegal operations are strictly prohibited; safe electricity use must be ensured at the construction site. Distribution boxes must be installed with leakage protectors in accordance with regulations. Distribution lines must comply with specification requirements. It is strictly prohibited to use electricity that does not meet the regulations. Electrical materials and wires required by industry regulations are strictly prohibited from live work.

5. During mining and excavation construction operations, the layout of underground communication facilities, pipeline lines, etc. should be first ascertained. Blind and brutal construction, which may cause economic losses and affect the company's reputation, is strictly prohibited.

6. The loading, unloading and installation of culverts and other materials must comply with safe operating specifications. Illegal operations and illegal commanding are strictly prohibited, and mixed loading of people and goods in transport vehicles is strictly prohibited.

7. Employees must be equipped with and wear protective equipment and tools during construction operations. It is prohibited to enter the construction site wearing slippers, bare feet or shirtless.

8. Strengthen traffic safety education for employees to prevent traffic accidents while employees are away from home.

9. Educate employees to abide by laws and regulations, strictly prohibit pornography, gambling, and drug activities, and strictly prohibit employees from participating in illegal and criminal activities.

10. Fire safety work must be done well to strictly prevent fire alarms and fire accidents at construction sites and residential areas.

11. For various safety production accidents, rescue operations should be organized immediately in accordance with relevant regulations, the site should be protected, and reported immediately to Party A’s leaders and departments. All possible measures should be taken, and no concealment or shirk is allowed. ,escape.

3. Form of Responsibility

When signing the contract, Party B must pay Party A a deposit for the quality and safety of the project. The deposit for the quality and safety of this project is 200,000 yuan.

4. Management of margin: Party A’s finance department will set up a special account for margin management for special management.

5. Rewards and Punishments

1. Critics who are notified by the safety supervision department at or above the municipal (district) level on construction site safety production will be fined 30,000 yuan each time.

2. For potential safety accidents or frequent safety problems, those who fail to make rectifications within a time limit or refuse to make rectifications will be punished according to Party A’s relevant systems.

3. Obtain a standardized construction site honorary certificate at the construction site and receive a reward of 30,000 yuan.

6. Principles for handling major liability accidents

1. Party B is the first person responsible for safe production at the construction site and is fully responsible for civilized construction and safe production.

2. If a major safety production accident occurs during the construction process, Party B shall bear the economic losses and legal liability caused by the accident. Party A assists in the aftermath of the accident, and any costs incurred will be included in Party B's construction settlement.

7. Assessment of this letter of responsibility: Party A’s Quality and Safety Department and Finance will conduct the assessment upon completion of the project. After assessment, if the goal of safe production and civilized construction is not achieved, in addition to the deposit being returned to Party A, all economic losses caused by the accident will also be borne by Party B; if the goal of the "Responsibility Letter" is achieved, the safety deposit will be returned to Party B in full. .

8. This letter of responsibility is made in two copies, one for Party A and one for Party B.

9. This letter of responsibility shall take effect from the date of signing and will automatically expire on the date when the project is completed and accepted.

Party A: Party B:

Legal representative: Director:

Year, month, day, month, day, year, month, day, production safety responsibility letter of the supervision unit 3

In order to conscientiously implement the "Work Safety Law of the People's Republic of China and the People's Republic of China", strengthen the safety production management work of the resident supervision office of the CSJ04 contract section of the Changchun-Shuangliao section construction project of the Changshen Expressway, maintain normal production safety order, and safeguard the national and the safety of people's lives and property, fully implement the principle of "whoever is in charge is responsible" for safety work, and further clarify the safety management responsibilities and requirements. The resident supervision representative XXX (Party A) and the safety supervision engineer XXX (Party B) signed the xx annual safety production responsibility Book.

1. Responsibilities of both parties

Party A’s safety responsibilities:

1. The resident supervision representative is the first person responsible for the safety supervision of the resident office and is responsible for the resident office Be fully responsible for safety supervision work.

2. Conscientiously implement national and project-related guidelines, laws, regulations, standards, policies and systems on production safety, and integrate production safety throughout the entire process of the work of the resident office.

3. Determine the full-time safety supervision personnel of the resident office to be responsible for establishing and implementing the safety production responsibility system for all employees. The division of labor is clear, the responsibilities are assigned to the people, and the implementation of the safety supervision responsibility system is inspected and assessed.

4. Organize the preparation of the safety supervision plan of the resident office and determine the safety supervision objectives of this project. Review the safety management system and safety technical procedures, personally preside over and approve major safety technical measures and hidden danger management plans, and effectively ensure the supervision of investment in safety production funds.

5. Comprehensively implement the "Emergency Emergency Plan" and various safety measures through education, inspection, analysis, troubleshooting and other methods, and proceed from the overall situation, supervise and require all supervisory personnel and Other personnel shall do a good job in production safety.

6. Adhere to the regular production safety meeting system and analyze, deploy, implement and record the safety production work of this project. Timely implement the spirit of the safety production instructions of superior units, summarize experience, analyze the situation, and solve existing problems in safety production, so as to be able to talk about safety and emphasize safety everywhere. At the same time, we actively organize and participate in special production safety activities at all levels to ensure that the participation rate and education rate of resident office personnel reach 100%, and improve the safety production awareness of supervisory personnel.

7. Adhere to the safety production inspection system, conduct frequent inspections of resident personnel, facilities and equipment, roads and resident areas, and promptly discover and eliminate various accident hazards.

8. Assist government departments, headquarters, and general director’s offices to inspect and supervise the work of safety supervision personnel in resident offices.

9. Assist in the investigation, analysis and handling of safety accidents, implement the principle of "four no-misses" for accidents, and supervise and inspect on-site rectifications after the accident.

10. Organize and compile the monthly report on safety supervision work of the resident office and the special monthly report on safety supervision.

11. Ensure that there are no fires, explosions, food poisoning, thefts, robberies and other vicious accidents at the site; no accidents involving serious injuries to employees; no driving accidents or liability accidents with a loss of more than 10,000 yuan; There were no major equipment damage accidents; there were no liability accidents caused by illegal command, dereliction of duty, etc.; there were no other types of accidents caused by improper support in our area.

Party B’s safety responsibilities:

1. The safety supervision engineer is the specific implementer of project safety management. He is responsible for the specific management of safety production supervision and inspection of this project, and is responsible to the resident supervision representative. Responsible for the safety accidents in the project.

2. Safety supervision engineers should carefully study the laws, regulations, norms, procedures and standards related to safety production; especially the "Safety Law" and "Construction Project Safety Production Management Regulations"; mandatory provisions for project construction related content, continuously improve the level of monitoring and management of production safety, and actively implement various production safety monitoring and management systems.

3. Prepare safety supervision implementation details and clarify safety supervision methods; safety supervision measures; and control points of safety supervision. Before the commencement of sub-projects with greater risks, the construction unit should explain the relevant contents in the special safety supervision rules to the construction unit.

4. Assist the resident supervision representative to prepare the safety emergency plan for the resident office and organize and participate in drills.

5. Consciously accept production safety education and training organized by superior departments, master necessary production safety knowledge, improve production safety skills, and enhance safety accident prevention and emergency response capabilities.

6. Supervise the construction unit to promptly report the qualifications of subcontracting units, the qualifications of third-category personnel and special personnel.

7 Review the safety technical measures or special safety construction plans in the construction organization design and provide opinions.

8. Review the safety technical regulations, operating procedures and safety technical measures of the project department to ensure that it is technically feasible.

9. Supervise the construction unit to establish and improve the safety production guarantee system at the construction site, and check the deployment of full-time safety production management personnel at the construction site.

10. Review the acceptance procedures of construction machinery, scaffolding and other safety facilities of the construction contractor, and sign opinions.

11. Check the construction unit’s construction safety disclosure and disclosure records for sub-projects with greater risks.

12. Responsible for the supervision of safety training, education and assessment work of the project department.

13. Supervise construction units to conduct safety self-inspections and participate in safety inspections on construction sites. Regularly hold production safety work meetings to analyze production safety trends and resolve existing problems in production safety in a timely manner.

14. Strengthen safety technology management, actively adopt advanced safety technologies and safety protection equipment, and organize research and implementation of rectification plans for major accident hazards.

15. Regular or unscheduled inspections of the safety conditions of the construction site should be carried out at least once a day. All working surfaces of sub-projects with greater risks should be inspected in place every day, and Keep good records, cooperate with the production safety department in supervision and management, and promptly request the construction unit to make rectifications in writing for areas with potential safety accidents found during inspections. If the situation is serious, order the construction unit to temporarily stop construction and report to the construction unit. If the construction unit refuses to make corrections or stop construction, it shall promptly report to the superior authority.

16. For key parts of the project that involve safety, special construction procedures and major hazard sources that involve safety, safety supervision engineers must conduct site visits, truthfully and accurately prepare safety site records and report them in a timely manner. Supervision records should be kept and archived for future reference. When standing by, they should stick to their posts and perform their duties. When problems are discovered, they should promptly ask the construction unit to make corrections. Major problems should be reported to the resident supervision engineer in a timely manner, issue a construction suspension order and take emergency measures in a timely manner to ensure Construction organization and safety.

17. Assist in the investigation and analysis of safety accidents and fire accidents, and specifically supervise and inspect the on-site rectification after the accident.

18. Prepare monthly reports on safety supervision work and special monthly reports on safety supervision.

19. Fill in the safety supervision diary.

20. Collect and organize safety supervision data (including image data), and file them together with the supervision data after completion.

2. Responsibility

1. If Party A fails to fully complete safety responsibilities during the project construction process, Party A shall assume corresponding responsibilities in accordance with the relevant provisions of the safety responsibility letter signed with the project. Those with serious consequences will bear corresponding legal responsibilities in accordance with the law.

2. If Party B causes a safety accident due to work errors, Party A has the right to hold Party B responsible for safety. If the circumstances are serious, Party A shall bear corresponding legal liability in accordance with the law.

3. This Letter of Responsibility is made in duplicate, one copy shall be deposited by Party A and Party B respectively, and shall come into effect on the date of signature by the responsible persons of both parties.

Signature of the responsible person of Party A: xx Signature of the responsible person of Party B: xx

xx year x month x day xx year x month x day

xx office supervision unit Safety Production Responsibility Letter 4

In order to ensure production safety, prevent accidents, and protect the personal safety of employees, in accordance with the "Mineral Resources Law of the People's Republic of China" and the "Construction Law of the People's Republic of China" 》"Mining Safety Law of the People's Republic of China" and "Production Safety Law of the People's Republic of China" strengthen safety production work, implement the policy of "safety first, prevention first, comprehensive management", firmly Establish a safety awareness that "safety responsibility is more important than Mount Tai" and continuously create a new situation in safety production. Now we have signed a safety production responsibility letter with the safety responsible persons of each responsible unit of the company's project construction:

1. Target management content< /p>

(1) The enterprise establishes a production safety management organization, has full-time safety officers, reports it to the safety committee office for filing, implements it at all levels and signs a production safety responsibility letter.

(2) Project managers, safety officers, technicians, gunners, manipulators and other special operations personnel must hold certificates to work, with clear responsibilities, assigned responsibilities to people, safety measures in place and systems on the wall.

(3) There are 5 production safety slogans and 1 warning sign. Employees will be educated on production safety at least once a week, and records will be formed for future reference. Each employee will be charged a safety deposit of 50 yuan per month, which will be cashed out during the year.

(4) Mines must operate in accordance with mine safety operating procedures, and violations of rules and regulations and illegal command and operations are prohibited to ensure safe production and the safety of people's lives and property.

(5) Before operation, a safety inspection must be carried out on the working surface and dangerous rocks and other dangerous objects must be removed. During operation, observation and inspection should be carried out at any time. When it is found that there are cracks in the working surface that may collapse, or there are large pieces of pumice floating mud and umbrella eaves hanging from the upper part, or there are other safety hazards, they must be dealt with quickly, and reliable safety must be ensured during the treatment. Measures should be taken, and personnel and equipment in areas threatened by it should be evacuated to safe areas and eliminated in a timely manner. A dedicated person should be responsible for the treatment, and there should be records and results.

(6) Anyone entering the work site must wear a safety helmet. Safety ropes must be used when working on steps with a height of more than 2 meters from the ground or a slope of more than 30 degrees. The safety rope should be tied to a secure place and must be carefully checked before use. Its safety factor should not be less than 5. The length of the tail rope should not be greater than 1 meter and to ensure safety, it is forbidden for two people to use a safety rope at the same time. It is forbidden to go up and down the same slope. Double or multi-layer operation at the same time. Labor supplies should comply with national inspection standards, workers should be guided and supervised to use them correctly, and they should be checked and updated frequently.

(7) Blasting operations must strictly comply with the provisions of the national standard gb6722-86 "Blasting Safety Regulations". At the same time, a timed blasting system must be implemented, with full-time blasters carrying out blasting operations in the second half of the prescribed time. It is prohibited to fire off blasting during work and during production, and it is prohibited to conduct blasting operations in thunderstorms, nights and foggy days.

(8) The responsible unit should purchase insurance for its employees and ensure that no fatal accidents occur during the liability period.

(9) Responsible units should strengthen the prevention and control of dust, noise, etc., and formulate complete measures for environmental protection, flood prevention, vegetation restoration, and prevention of water and soil erosion.

(10) The responsible unit must formulate an emergency rescue plan, and at the same time set up an emergency rescue team and identify rescue personnel. When a safety production accident occurs, rescue should be organized immediately and reported to the relevant departments in a timely manner.

(11) The responsible unit shall not cause any production safety accidents involving death or disability.

(12) The legal representative of the responsible unit and the safety management personnel of the responsible unit must attend the company's safety work meeting on time.

2. Person responsible for target management

The first person responsible: the legal representative of the responsible unit; the second person responsible: the project manager and safety officer of the responsible unit.

3. Objective management inspection

(1) The responsible unit shall conduct a comprehensive inspection of production safety before, during and after work every day.

(2) The company's safety committee office conducts regular safety production inspections on the enterprise every month, and also conducts random inspections.

(3) Accept the supervision of the masses. Once safety hazards are reported, the Safety Committee Office should promptly put forward rectification opinions, make rectifications within a time limit, and suspend production for rectification if the rectification fails.

IV. Target Assessment Methods

(1) All enterprises with target management content tasks are targets for annual assessment.

(2) For enterprises that complete the target management content tasks, the company will award first, second and third prizes after inspection, assessment and acceptance. The first prize is 15,000 yuan and the second prize is 8,000 yuan. The third prize is 4,000 yuan.

(3) Enterprises that fail to complete target management will be dealt with according to the following provisions:

1. Punishment targets: the legal representative of the responsible unit, safety officers and personnel responsible for safety management.

2. Treatment methods:

(1) If the safety officer and safety management personnel of the responsible unit are found to be absent from the work site, the company will be fined xx yuan and the safety officer 1,000 yuan each time.

(2) If a special operator is found to be working without a certificate, the company will be fined 200 yuan at a time and made corrections within a time limit.

(3) If suspended rocks are found, the enterprise will be fined 500 yuan at a time and personnel will be organized to remove the suspended rocks immediately.

(4) If an operator is found not wearing a safety helmet, the company will be fined 100 yuan per person. If a safety rope is not tied, the company will be fined 200 yuan per person, and rectification will be made on the spot; if it is found twice, The enterprise shall organize employees to study; if it is discovered three times or more within a year, the supply of explosives will be stopped and production will be suspended for more than one day for rectification.

(5) If it is found that mining is not carried out in accordance with the operating procedures, the enterprise will be fined 5,000-10,000 yuan at a time, and the company will be suspended for more than 7 days for rectification. Production will be resumed after the rectification is passed and accepted.

(6) If any illegal transportation, loading, or detonation of explosives is found, the enterprise will be fined 5,000-10,000 yuan at a time and suspended for more than 2 days for rectification.

(7) Any responsible unit that does not attend the town safety study and meeting without any reason will be punished with a safety study fee of 30 yuan per person, and will be dealt with according to the meeting attendance system. If a person fails to attend the meeting for a total of 3 times, he will be suspended from production and study for more than 5 days. .

(8) If a work safety accident results in disability, the enterprise will be fined 10,000 yuan per person, and the relevant responsible persons will each be xx yuan. At the same time, the safety deposit of 50,000 yuan paid when setting up the factory will be deducted, and so on.

(9) In the event of a work-related injury or death, the enterprise will be fined 50,000 yuan per person, and the relevant responsible persons will be fined 5,000 yuan each, and all safety deposits will be deducted, and so on. At the same time, production can only be resumed after rectification.

(10) If a safety incident is concealed and not reported, and if it is verified to be true after reports from the public or parties concerned, the enterprise will be fined 100,000 yuan at a time, and the penalty will be doubled in accordance with the above provisions according to the size of the safety incident concealed.

(11) If there are serious safety hazards and refuse to rectify, the company will be ordered to make rectifications until the safety hazards are rectified.

Signature of the responsible person of Party A: xx Signature of the responsible person of Party B: xx

xx year x month x day xx year x month x day

xx office;< /p>