Excellent sample of safety inspection work report

Safety inspection is an important management task for modern enterprises. Only by ensuring safety can an enterprise develop in the long run. How to write a safety inspection work report? This article is a sample safety inspection report that I compiled for everyone, for reference only.

Safety Inspection Report Sample 1

According to the requirements of the college’s fire safety regulations and in comparison with the “Fire Protection Law of the People’s Republic of China” and the “Fire Protection Regulations of the Inner Mongolia Autonomous Region”, I am in On the afternoon of March 19, under the organization of the Comprehensive Section of the Security Department, a centralized inspection of fire hazards was carried out in the teaching buildings, student apartments, canteens, experimental training buildings and other service institutions in the hospital. During this inspection, we registered the fire hazards and unsafe factors discovered and issued a rectification notice to eliminate existing unsafe factors. The basic situation of the inspection is now reported as follows:

1. Inspection situation

Public facilities:

1. Teaching building: Safety precautions in the teaching building The measures are basically complete, the fire hydrant test is normal, the fire indicator light is normal, the fire extinguisher is normal, and the safety passage is clear.

2. Experimental training building: Fire hydrants have no nozzles and emergency lights cannot be used.

3. Old laboratory building: There is a serious lack of fire safety facilities in the building. There is no fire hydrant on the first floor, and one fire hydrant is missing on the second and third floors. Three fire extinguishers in the heat treatment laboratory (first floor) need to be replaced. Two need to be repaired and updated; four fire extinguishers need to be replaced in the carpentry room; two fire extinguishers in the foundry laboratory need to be updated and repaired; the walls on both sides of the north end of the third floor are peeling off and the bamboo strips are exposed, which is a fire hazard. The south end also has the same problem.

4. Student apartment building: The fire hydrants in Building B are seriously damaged (missing nozzles and valves) and are all rusty, basically unable to be used normally; the emergency light power supply in Building C is privately connected by students. Phenomenon: The emergency lights on the D floor of the apartment are not on; one gun tip is missing on the third and fourth floors of the boys' area, three gun tips and a water bag are missing on the fifth floor, and there is no gun tip and no water bag on the sixth floor. There are two gun heads missing on the third floor of the girls' section. The fire hydrant in Building E had no water and was seriously damaged; the fire hydrant in Building F had no water.

5. Other public service facilities: private electric furnaces in substations are used for heating, which poses hidden dangers; there are no fire extinguishers in the boiler room; a fire safety passage in a canteen is occupied by the business hall of China Unicom, and there is no dedicated storage for liquefiers between. The four small restaurants downstairs use liquefied gas, and there are no special storage cabinets or rooms, nor are they equipped with fire extinguishers.

Private service facilities: Some catering operators downstairs do not have fire extinguishers.

2. According to the spirit of the Party Committee of the college on building a "safe campus", the following suggestions and requirements are put forward:

1. In accordance with the requirements of the rectification notice, within the prescribed time limit Make corrections within.

2. Determine a dedicated person to be responsible for the management of fire protection facilities, establish a responsibility system, strengthen the maintenance of fire protection facilities, conduct regular inspections and tests, and submit the list of identified fire protection responsible persons to the Security Office for record.

3. It is recommended that the logistics group inspect the power lines in the student apartments, clean up the privately pulled and connected wires by students, resolutely put an end to the use of high-power electrical appliances such as electric stoves and heaters, and eliminate the use of electrical appliances. Fire hazard. At the same time, the behavior of private electric furnaces in substations will be dealt with.

4. Office computers, printers and other office electrical facilities in each unit should be turned off when not in use, and the power should be cut off when leaving get off work.

5. The logistics group should strengthen fire safety education for students and business owners. Recently, I contacted the school fire department to conduct a fire safety knowledge and skills (fire extinguishing equipment use, escape skills) training for our students. Safety Inspection Report Sample Part 2

In order to conscientiously implement the "Notice of the Provincial Joint Press Office forwarding the Provincial Government General Office's Documents on Carrying out Safety Production Inspections in the Province" (Yunong Xinlian [2013] No. 678) and the "Notice of the Office of the People's Government of Jingdong Yi Autonomous County on Centralized Production Safety Inspections" (Jingzhengbanfa [2013] No. 134) require that we further strengthen the supervision and management of production safety in our company, combined with the safety production inspection in our company In practice, we must conscientiously implement the safety production responsibility system, increase the investigation and rectification of hidden dangers, and prevent the occurrence of safety production accidents.

The Associated Press has conducted safety inspections on 21 business outlets and three service points. The inspection status is now reported as follows:

1. Basic situation

Based on the actual situation of our company, a safety plan has been drawn up Implementation plan for production inspection and established a leading group. We should focus on both business development and safety production, and carry out quarterly authenticity inspections and safety production inspections in parallel, and form a regular basis, with inspections being conducted every quarter. Key contents of the inspection: Business premises: anti-tailgating linkage doors, warehouse doors, business counters and bulletproof glass, anti-theft doors, business counters, self-defense knives, steel forks, maces, doors, windows and circuit facilities of the warehouse duty room, Other doors, windows, power lines, blade switches, etc.; self-service banks or ATM machines: doors, windows, power lines, protective cabins (kiosks); staff dormitories: doors, windows, power lines, blades, switches; employee security skills and knowledge training, office machinery and equipment, power supply lines, fire protection facilities, emergency evacuation channels, emergency plans and drills, monitoring equipment, escort vehicles, official vehicles, the storage and use of generators, elevators, and other major sources of danger. Combined with the annual activities of the standard, check whether the safety production rules and regulations are established and improved; the implementation of the on-site rotation system for leading cadres; the equipment of fire protection equipment; the safety education and training of all employees; the signing of safety responsibility letters; whether safety hazards are effectively investigated and managed; emergency plans Drill status; implementation of various safety and security systems, etc.

2. Existing problems

Judging from the inspections, all companies attach great importance to production safety, and have conducted internal safety inspections and made rectifications as required. However, some companies still have some problems in safety production work, such as: job responsibility system is not implemented, safety hazard rectification is not in place, etc.

During this safety production inspection, *** found 35 problems, 31 were rectified immediately, and 4 were rectified within a time limit. The main problems discovered during the inspection are:

1. The safety production management system, job operating procedures, and safety management institutions are not sound, and responsibilities are not assigned to people.

2. Safety education and training for employees is insufficient.

3. Electrical appliances and circuits are not regularly checked, the circuits are aging, the wiring is not standardized, the temporary electricity is connected privately, the switch is not covered, etc.

4. The engine oil is placed randomly and there is no dedicated person to keep it.

5. Fire-fighting equipment is insufficiently equipped, expired, and not placed in a conspicuous location.

3. Rectification measures

In response to the problems identified above, in the next step of work, we must strengthen measures, urge rectifications on time, review on schedule, track rectifications, and ensure that rectifications are in place.

1. Strengthen leadership and establish awareness of production safety. It is necessary to strengthen measures and conscientiously implement the safety production responsibility system. Directors of various cooperatives must include safety production work in their important agenda, and the top leaders must personally grasp it. It is necessary to increase the intensity of safety production work, conscientiously implement the policy of "safety first, prevention first", adhere to the principle of who is in charge and who is responsible, implement the safety production work responsibility system at all levels, and be practical and meticulous. Production safety and fire prevention work must be carried out in strict accordance with relevant regulations.

2. Abide by rules and laws, and establish and improve safety production rules and regulations. In accordance with the requirements of the government and relevant departments for production safety, all companies must establish and improve production safety rules and regulations, job operating procedures, and organizational structures, so that there are rules to follow, laws to follow, organizational implementation, system implementation, and measures. implement. At the same time, we must do a good job in publicity, education and training on production safety, and enhance the awareness and legal concepts of production safety among leaders and employees.

3. Conduct frequent inspections, carefully investigate and rectify hidden dangers. Our inspection work on production safety must be regular, institutionalized and standardized, and the word "diligence" should be mainly reflected in our work. We must frequently inquire, supervise and inspect frequently. Enterprises should be urged to speed up rectification of potential safety hazards raised during inspections, nip hidden dangers in the bud, and reduce the occurrence of safety production accidents.

4. Strict discipline and serious accountability. We must do a good job in preventing production safety accidents and prevent the occurrence of various accidents. Once an accident occurs, we must conscientiously implement the accident reporting system and report it in a timely manner step by step. For companies where safety production accidents occur, we must follow the principle of "four no-misses" and seriously investigate the responsibilities of the main responsible persons and relevant responsible persons to ensure that the state and The safety of people’s lives and property.

Safety inspection report sample article three

In order to further strengthen and improve the safety work of the project department, respond to the call of the institute, effectively protect the life safety and property safety of the majority of employees, and ensure the normal construction order of the project, combined with the actual situation of the project department, Our department has carefully and carefully inspected the safety work at the construction site, and carried out hidden danger inspection and management activities at the construction site. The self-inspection and rectification situation is summarized as follows:

1. Safety management

1. Establishment and improvement of safety organization structure

The project department has established a safety management network, safety production responsibility system, and safety management system with the project manager as the first responsible person. A full-time safety officer is assigned to be responsible for on-site safety inspections and safety inspections at the construction site, forming a top-down safety assurance system.

2. Implementation of safety management system and responsibility system

(1) At present, the project department’s safety regulations are complete and highly operable. Continuously improve the execution of safe and civilized construction systems to strengthen safe and civilized construction management and prevent accidents.

(2) In order to ensure safe production, the project department formulated safety target indicators according to the company's relevant requirements and decomposed them layer by layer, clarified the safety responsibilities of personnel and departments at all levels, and carried out safety inspections during the construction process. Supervision is implemented in place.

The project department signed a "Safety Responsibility Letter" with the heads of each construction team, and strictly implemented the safety production responsibility system at all levels and the safety accident liability investigation regulations. The quality and safety department of the project department Supervise, inspect and assess the implementation of the system, promptly remind and educate those who violate the responsibility system, and provide rewards and punishments based on assessment results.

3. Safety inspection and hidden danger investigation

In addition to daily safety inspections, the project department also purchases various safety warning signs and construction signs according to the on-site conditions. During construction Corresponding warning placards should be placed at site entrances, passageways, near electrical equipment and other places to remind staff to pay attention to protect themselves and others and eliminate potential safety hazards.

4. Safety education and training

(1) The project department conducts timely safety education and training for new site managers and workers from time to time. The main contents of the training include: corporate rules and regulations, basic safety knowledge, construction safety precautions, various relevant safety technical measures and operating procedures, emergency rescue plan learning, etc.

(2) Participate in safety technical training and certification for electricians, welders, loader drivers and other special operations personnel as required.

(3) Each construction team conducts its own team safety education activities.

2. On-site construction safety conditions

1. Temporary facilities

(1) The temporary facilities have been planned strictly in accordance with the requirements and the layout is relatively reasonable.

(2) Temporary facilities meet technical requirements such as fire protection, rainproofing, and heat preservation. Personnel are arranged to patrol the living and office areas, construction areas, warehouses, and mechanical equipment parking areas 24 hours a day to ensure the safety of on-site supplies and materials.

2. Safe use of electricity

The construction site ensures "one machine, one gate and one leak" for electrical equipment, ensuring the safety of electricity; warning signs are placed on power supply equipment . Lighting fixtures and power supply lines shall be installed as required. Electricians on duty will conduct regular inspections and deal with hidden dangers in a timely manner to prevent accidents.

3. Special equipment

A dedicated person is responsible for the daily operation, maintenance, shift handover records, etc. of major mechanical equipment. During the use of equipment and transportation vehicles, regular inspections, repairs and maintenance should be carried out, and equipment operation, repair and maintenance records should be filled in. Immediately stop work, rectify or remove equipment with potential safety hazards. Scaffolding construction

4. Fire management

The project department has formulated a fire management responsibility system and implemented it in place. Developed and improved fire emergency plans.

The project department has stepped up inspection and monitoring of fire-prone areas. < /p>

(2) There are no violations in work areas or parts where fireworks or smoking are prohibited.

5. Safety protection facilities

During construction, safety management personnel can formally wear and use protective equipment such as safety helmets and safety belts; protective facilities and safety equipment are set up at cave entrances and dangerous locations. Obvious warning signs; fire-fighting facilities are installed near electrical parts and flammable materials.

3. Problems in safety management

1. Individual personnel have weak safety awareness, and habitual violations still occur at the construction site.

2. The layout of construction power lines is messy and needs further standardization.

3. Equipment is regularly inspected and various systems are improved; however, the inspection data and records of the equipment themselves are incomplete; further improvements.

4. Some safety protection facilities have not kept up with the progress of project construction, causing safety protection to lag behind during construction.

4. Rectification measures taken:

In order to ensure the safety of project construction and eliminate various safety hazards, the project department proposed the following rectification measures for the main problems existing during the self-inspection process:

1. The project department will strengthen supervision and carry out safety education in batches, using daily inspections, inspections, meetings, safety education and training, bulletin boards, newspapers, documents and other methods to educate employee cadres on safety knowledge, Education and publicity on laws and regulations, etc., to improve employees’ safety awareness and sense of responsibility, and to prevent the occurrence of safety accidents.

2. We will continue to pay attention to the issue of electricity consumption in construction, strictly investigate the illegal use of electricity in workers’ dormitories, and conduct unified and standardized layout of on-site wiring.

3. Strengthen the supervision of habitual violations. To strengthen safety education, management supervision and punishment, we must ideologically improve the safety awareness of employees.

4. Improve and perfect the system to ensure that comprehensive safety management work is well-organized and implemented. Strictly implement the responsibilities of all levels and departments in accordance with the safety responsibility system.

5. Carry out safety inspections and hidden danger inspections and management on a regular basis in accordance with the regulations of the project department in a timely manner, and do a good job in finding and rectifying safety hazards at the construction site.

In short, through this major inspection, some shortcomings and omissions in the safety work of the project department were discovered. The project department made timely rectifications and brought them under effective control, but safety work is a long-term task. The project department will continue to pay close attention to safety, consolidate the basic work of safety management, improve the safety awareness of the majority of employees, enable various tasks and requirements of safety management to be better implemented, further enhance their awareness of safety responsibilities, and clarify their respective responsibilities. Responsibilities to provide safety guarantee for the smooth progress of project construction. >>>More "Safety Inspection Work Report" on the next page