Etiquette and production process of wearing badges

In business situations, should business people or service personnel wear badges on the left or right? Do you know the etiquette of famous brand

Etiquette and production process of wearing badges

In business situations, should business people or service personnel wear badges on the left or right? Do you know the etiquette of famous brands? I'll tell you next.

Badge wearing etiquette: Badges are usually worn on your left chest, and most Chinese and foreign customs are the same.

The formation of this habit may be due to:

1. Most people are right-handed, so it is more convenient and easier to put the famous brand on the left chest with your right hand.

2. People's heart is on the left, so others may notice it more easily;

In addition, in China:

1. Since ancient times, most people have followed the etiquette habit of "left is top";

2. In ancient China, the reading habit was reading from right to left. When you look at others, you should start from your own right and the other person's left. It should be easier for others to see the staff badge on their left.

China's early badges were all worn on the left chest, and the 07-style general's dress wore the rank badge on the left chest and the name badge on the right chest.

In foreign countries, etiquette advocates wearing a badge on the right, on the grounds that:

1. When shaking hands, the body on the right side of the person will move forward slightly, and the name tag will be worn on the right chest to make it easier for the guests to see;

The guest's reading habit is reading from left to right. When you look at others, you should start from your own left and the other person's right. It should be easier for guests to see the employee's name tag on their right.

Summary:

The left and right sides of the 1. badge should be guided by whether the customer can clearly see it.

2. If the uniform is designed asymmetrically, the badge should be worn on the side that can balance the visual center of gravity.

3. No matter whether the badge is worn on the left or right, all employees in the same unit or company should be consistent.

The process of making name plates is 1. First of all, the printed and cleaned objects are placed flat on the operation panel with the same level for dripping.

2. According to the dosage, take a cup, accurately weigh 90g of glue A, then weigh 30g of glue A and glue B, and mix them evenly according to the ratio of 3: 1. Some crystal glue components are 2: 1, others are 1: 1.

3. Take a clean syringe, suck the prepared glue into the syringe and drop it evenly on the surface of signs, badges and so on. Generally, the thickness of crystal glue layer is 2mm, so it can be leveled naturally.

4. After dropping crystal glue for 3-5 minutes, observe whether there are bubbles or dust particles on the rubber surface. If there are small bubbles, you can pick them off with a small needle. If you find that the dead corner is not smoothed with crystal glue, you can extradite them with a needle.

5. The poured name plate is cured at room temperature of 20℃-22℃ 10- 14 hours, and becomes a crystal plate with non-stick surface after hardening.

6. If it is an adhesive, trademark, etc. Its thickness is very thin and its boundary is not obvious. It is easy to cause crystal glue overflow when pouring, and it is difficult to reach the thickness of 2mm. Therefore, it is necessary to control the viscosity according to different conditions when making crystal glue, and 1-2 hours can be placed in the application process to improve the viscosity and adapt to the pouring of thin crystal glue.

7. Make a crystal glue name tag with a thickness of more than 2mm, which can be dripped twice. After the first drip, it will cure for 3-5 hours, and then drip another layer.

8. In order to clean the plastic after it falls, it is necessary to clean the container made of toluene, xylene and cyclohexanone. If the glue is insoluble in any solvent after hardening, it must be cleaned in machines and containers before hardening. The products made of crystal glue have the advantages of good visual effect, high transparency and high gloss, and should be widely used in screen printing industry. Note: If the weather is very cold, first heat the glue A and dilute it to about 15 degrees.

The purpose of the work badge is that the size of the work badge is mostly about 2-3 cm, and it has one or more company names, company logos, names, numbers, positions, subordinate departments, corporate images, etc. You can put it on it. Due to the relatively small size of the badge board, the above contents should be simplified as much as possible. It is mostly applicable to enterprises, companies, central institutions, public business halls, service windows, etc. in all walks of life, without domain restrictions.

Badge is also called badge, number plate, engraved card, work number plate, badge, badge, badge, badge, badge, etc.

A combined name plate with patterns or characters engraved on the surface by laser is characterized in that the base material of the name plate is made of any one to three materials of bamboo, wood or composite materials by splicing or/and compounding or/and inlaying. The utility model is formed by splicing, compounding or inlaying base materials of different materials, so designers can match according to the lines, colors and characteristics of different materials to design and produce unique and natural background patterns, so as to highlight the characters and patterns on the name plate and set them off, enrich the expression ways of the name plate and make the name plate more beautiful.