Quality and Safety Commitment Letter

In the ever-changing modern society, a letter of commitment is closely related to our lives. A letter of commitment is the promisor’s complete agreement with the offeror’s offer, expressed in writing. How to write a commitment letter to avoid stepping into the trap? The following are 10 quality and safety commitment letters that I have compiled for you. They are for reference only. I hope they can help you. Quality and Safety Commitment Part 1

In order to conscientiously implement the "Food Safety Law" and "Agricultural Products Quality and Safety Law" and other laws and regulations, effectively protect the safety of people's lives and property, and safeguard the legitimate rights and interests of consumers, This producer and operator makes the following commitments:

***Same Commitment

1. Strictly abide by and implement laws such as the Food Safety Law and the Agricultural Products Quality and Safety Law, Laws and regulations; engage in production and business activities in accordance with the law;

2. Be honest and trustworthy, and do not engage in fraud;

3. Actively cooperate with and support the supervision of agricultural product quality and safety supervision departments in accordance with the law ;

4. If any illegal behavior occurs, be willing to accept the handling of regulatory authorities in accordance with the law.

Commitments of agricultural product producers

1. Formulate production technical procedures, production management systems, production recording systems, agricultural input use systems, agricultural product quality self-inspection systems, agricultural product harvesting systems, etc. , and strictly enforce it;

2. Strictly implement the regulations on the use of agricultural inputs and establish complete agricultural input use files.

3. Resolutely put an end to the use of prohibited pesticides, antibiotics and food additives. Pay attention to the pesticide safety interval when harvesting vegetables and fruits to ensure that pesticide residues in vegetables and fruits on the market do not exceed standards.

Fourth, we must improve the production and sales files of agricultural products and keep the files as required; implement a recall system for unqualified agricultural products.

5. Accept the supervision and management of agricultural product quality supervision staff in accordance with the law, and accept the decisions made by agricultural product quality and safety supervision agencies.

6. Bear economic and legal responsibilities in accordance with the law for adverse consequences to society caused by product quality problems.

Commitments of agricultural input operators

1. Strictly establish and improve business files and implement purchase and sales ledger records;

2. Purchase goods from legal production enterprises, Check the quality of purchased goods;

3. Do not deal in agricultural inputs banned by the state or fake and inferior agricultural inputs;

4. Introduce scientific, reasonable and safe products to buyers

5. Bear the legal responsibility for safety accidents directly caused by the agricultural inputs sold by itself. Quality and Safety Commitment Letter Part 2

Our company’s safety indicator for this project is that there will be no major work-related injuries or fatalities. Based on the conditions of this project, the following safety protection and civilized construction measures have been formulated.

1. Safety protection measures

1.1 Establish a safety management system

Establish a sound construction safety management system and implement a safety responsible person system. Project manager Tao Jian is the first person responsible for construction safety. The project department has a full-time safety officer, the construction team has a part-time safety officer, and the team has a safety manager to ensure that safety assurance measures are implemented at all levels, including both executors and supervisors.

1.2 Strictly implement the "Construction Project Safety Production Management Regulations".

1.3 Adhere to the three-level safety education for all employees, and provide the three-level safety education for the team, project department, and company to the workers who are on the job. Workers who have not received the three-level safety education will not be allowed to work. Adhere to the one-hour safety learning system every week, strive to improve the safety awareness of all employees, master necessary safety knowledge, and improve self-protection capabilities.

1.4 Conduct safety technical briefings. Before the construction of each part of the process, the security department and technical department will organize safety technical briefings for each manager and operator, and propose safety technologies for each period and each process. Requirements and safety precautions.

1.5 Conduct regular safety inspections, and conduct daily inspections of the team and weekly inspections of the project department as required.

Potential safety hazards discovered during safety inspections are required to be thoroughly rectified. If rectification is not carried out as required, work will be stopped resolutely for rectification. Correct various violations in a timely manner and impose corresponding fines in accordance with relevant systems.

1.6 Strengthen the safety production management of the construction team. Conduct a safety qualification review of the construction team and identify the person responsible for safety. There must be a safety person in charge on site who is responsible for the safe production and management of on-site construction. Insist on providing safety technical briefings to the construction team before construction.

1.7 Carefully implement safety protection measures, pay attention to the investment of safety protection supplies, and fully guarantee the funds for various safety facilities required for safe production during construction.

1.9 Strengthen the management of special operations personnel. All special operations personnel, including electricians, welders, hoists, etc., must hold certificates to work. Those without certificates are not allowed to work.

1.10 Safety protection measures are set up at the construction site in accordance with regulations, and personnel entering the construction site must use safety protective equipment correctly in accordance with regulations.

1.11 The construction site must have safety slogans and signs, be equipped with fire-fighting equipment, be managed by full-time safety officers, and keep fire escapes open.

1.12 Set up safety production placards at conspicuous places on the construction site to enhance safety awareness.

1.13 Temporary facilities at the construction site, warehouses, storage and processing sites for wood, oil, flammable and explosive materials, including upper and lower areas that require fire work, hang safety signs, set up fire-fighting equipment, and equip part-time workers Firefighters to prevent or control fires.

1.14 Fire hydrants should be installed at the construction site and sufficient fire-extinguishing equipment should be provided. Materials are not allowed to be piled within five meters around the fire hydrant.

2. Civilized construction measures

2.1 Strengthen the construction of spiritual civilization, improve the ideological and political quality and professional quality of employees, and create a good corporate image.

2.2 Do a good job in promoting civilized construction on site, publicize the party’s principles and policies and corporate spirit, enhance awareness of civilized construction

, consciously implement civilized construction, and strictly implement the "Nanjing Construction Project Construction" On-site management measures.

2.3 In order to facilitate public supervision, a construction sign issued by the urban supervision department must be hung at the entrance of the construction site, indicating the project name, construction unit, on-site person in charge, construction license number, civilized construction person in charge, and complaint telephone number wait.

2.4 In order to prevent non-construction personnel from entering the construction site, the enclosure of the construction area shall be implemented in accordance with the relevant requirements of civilized construction management and enclosure shall be implemented. On-site office and work shed facilities must be reasonable, convenient, neat and uniform. As soon as the project starts, publicity slogans for civilized construction must be introduced simultaneously.

2.5 All construction management and operating personnel should wear badges when working.

2.6 During construction, effective measures must be taken to control flying dust, reduce construction pollution to the environment and greening, and strictly control noise.

2.7 All on-site construction personnel must wear safety helmets, and non-construction personnel are not allowed to enter the construction site without authorization.

2.8 Cooperate with the supervision engineer at any time to inspect the project quality, and always insist that the supervision engineer’s inspection of any process and components is reasonable. Engineering and technical personnel must actively cooperate and humbly accept the guidance of the supervision engineer. .

2.9 Construction materials and equipment should be classified and stacked neatly, the work site should be clean and orderly, and the site should be cleaned up after the work is completed; all office materials should be well recorded, neatly bound, and well documented.

3. Public Security Management Measures

3.1 Establish a specialized security agency to provide unified leadership for public security and security work.

3.2 Strictly implement the construction area access system, and all personnel must wear badges when entering the site.

3.3 Staff members are limited to the designated construction area of ??the project, and are prohibited from entering areas unrelated to the project without permission.

3.4 Staff members are not allowed to drink alcohol on the construction site or enter the construction site to work after drinking, and are not allowed to bring contraband into the construction site to maintain the safety of property and personnel.

3.5 After the material vehicle enters the unit and is loaded and unloaded, it immediately leaves the site and parks in the designated parking lot.

3.6 Strengthen the management of valuable materials, important equipment and large equipment at the construction site, strictly implement relevant systems, and set up protective facilities and alarm equipment to prevent materials from being stolen or damaged.

3.7 Extensively carry out legal publicity and "four defenses" education to improve the awareness of the broad masses of employees to defend project construction and abide by laws and regulations.

3.8 Carry out frequent safety inspections focusing on fire, explosion and theft prevention, plug loopholes, and take preventive measures promptly when hidden dangers are discovered to prevent problems.

3.9 Strengthen the management of the labor force, and assign dedicated personnel to educate the labor force on laws, regulations, and rules before they can start working.

4． Finished product protection measures

4.1 Finished product protection work management system

1) Responsibilities for finished product protection are divided and implemented to the posts and people.

2) Formulate the key contents of finished product protection and the implementation plan for finished product protection.

3) Develop finished product protection measures plans and implementation details in stages.

4) Develop an inspection system, cross-construction management system, handover system, assessment system, reward and punishment responsibility system, etc. for finished product protection.

4.2 Finished product protection measures

1) Develop an inspection system, cross-construction management system, handover system, assessment system, and reward and punishment system for finished product protection.

2) The project management department must conduct regular finished product protection awareness education for all subcontracting teams entering the site, and make the subcontracting teams aware of the need to do a good job in accordance with the contract, rules and regulations, and various protective measures. Finished product protection work is to ensure the quality of your own products and thereby protect your own honor and vital interests.

3) Handover procedures must be completed between the previous process and the next process, and the responsible engineers of the project management department must record the handover situation in the construction diary. All workers must be supervised by product protection personnel.

4) When the project management department formulates the monthly plan, it must make scientific and reasonable preparations based on the master control plan to prevent process inversion, cross-construction of unreasonable deadlines, and mutual repercussions caused by improper protective measures. The occurrence of damage, repeated contamination, etc.

5) Set up a warehouse on site to store materials and prevent erosion by wind and rain. For materials that are not suitable for moisture and are prone to rust, shelves should be set up in the warehouse to store them. When storing, stack them neatly and pay attention to the stacking height and stability.

6) During the transportation of materials and equipment, fragile materials and equipment should be handled with care, and the outer packaging should be removed after being transported to the operating surface. It is strictly prohibited to remove the outer packaging in advance to facilitate transportation.

7) For materials, equipment and equipment in the computer room that must be installed and are easily damaged or lost, they must be installed after closed conditions are formed, and a dedicated person shall be assigned to manage them.

8) The feet of the ladders and high stools used should be wrapped with linen or rubber to prevent slipping and damaging the completed floor tiles and other floors.

5． Safety Measures for Construction of Partial Projects

Based on the characteristics of the construction of technical parts, the following safety construction measures are formulated.

5.1 When manually excavating buried pipeline trenches, grading or reliable support must be carried out in accordance with regulations, otherwise construction is not allowed. Construction workers must always pay attention to whether there are cracks or landslides on the slope. Once discovered, the work should be stopped immediately, and construction can only be carried out after treatment and reinforcement. In addition, excavation of trenches with a depth greater than 1 meter at night should be avoided.

5.2 When manually transporting pipes, valves, etc., be careful to load and unload with care, move in a consistent manner, and look after each other. Before lifting heavy objects, you must first carefully check whether the spreaders and ropes are reliable. When lifting heavy objects, no one is allowed to stand under the lifted objects.

5.3 Before installing the pipeline, the debris in the pipeline should be cleaned and inspected. When pipeline construction is stopped in the middle, the pipe opening should be temporarily blocked to prevent small branches from entering the pipe.

5.4 After the valve is installed, it should be closed tightly.

It can be opened during the pressure test and remains closed after the pressure test. The flow rate will be adjusted during debugging or trial operation.

5.5 When excavating pipe trenches, the distance between the earth and the edge of the pipe trench shall not be less than 800mm. Materials and tools used shall not be stored beside the trench. During construction, both sides of the trench wall should be regularly checked for looseness, cracks or water seepage. , if there is a possibility of landslide, protective boards and supports should be added in time.

5.6 When there is water at the bottom of the trench after rain, drainage measures should be taken carefully and live wires should be prevented from conducting electricity in the water.

5.7 During the construction process, when transporting tools, materials, etc. into the pipe trench, they should be slid slowly, and personnel in the trench should pay attention to safety and avoidance.

5.8 When assembling the pipe or moving it horizontally, it is strictly forbidden to touch the mouth of the pipe with your hands to avoid cutting or crushing your fingers.

5.9 When using a portable grinding wheel or angle grinding, you should wear protective glasses, enter the workpiece slowly, and the direction of rotation should be correct. When operating, the face and the grinding wheel should be angled, and when out of use, wait until the rotation stops. The grinding wheel can be placed in a safe place.

5.10 When hoisting pipes, the drawstrings should be tied at both ends. The position of the center of gravity should be considered when turning or rotating the prefabricated parts to prevent slipping or shifting of the center of gravity and causing injury.

5.11 When assisting the welding team to weld the pipeline, necessary protective measures should be taken to prevent arc light from hurting the eyes. The feet should be placed on dry wooden boards or other insulating boards.

5.12 ??Temporary electricity use at the construction site must be managed by the electrician, and other personnel are not allowed to connect it without authorization. Wires should be laid according to regulations and hanging on steel scaffolding is strictly prohibited. Buried wires must be cased with steel pipes. All switch boxes are locked and the derrick is equipped with lightning rods. All power tools and electrical appliances must be equipped with leakage protection devices. Electrical circuits should be regularly inspected and repaired to ensure that the leakage protection devices are sensitive and effective. Strengthen the management of night lighting to ensure lighting in construction areas.

5.13 The winch and various electromechanical equipment should be operated and used by certified personnel. Others are strictly prohibited from operating and tampering with them.

5.14 The pressure gauges used for pressure tests must be calibrated before they can be used. The number of gauges should be at least two.

5.15 When performing a pressure test on a pipeline, the tightness of the pipe and the bracket and the reliability of the pipe blocking plate should be checked. Only after confirming that there are no problems can the pressure test be carried out.

5.16 When conducting pressure tests on pipelines with high pressures, the danger zone should be demarcated and personnel should be placed on guard to prohibit irrelevant personnel from entering.

5.17 During the pressure test, the pressure increase and decrease should be carried out slowly and not too quickly. The pressure must be carried out in accordance with the requirements of the design or acceptance specifications and must not be increased arbitrarily. Inspection can only be carried out after stopping the pump to stabilize the pressure. When leakage is found, repairs under pressure are strictly prohibited. The discharge port must not be aimed at wires, foundations and sites where there are people operating.

5.18 The pipeline purge port should be set up in an open and safe area. Communication should be set up between the purge port and the gas source, and a dedicated person should be responsible for safety.

5.19 until the safe construction of the project is completed. Quality and Safety Commitment Part 3

To:

Our company is fully aware of your company's business philosophy and requirements of "quality is the life of the enterprise and safety is above all else", and strictly abides by it. In accordance with the provisions of relevant laws and regulations, the construction site shall be strictly managed in accordance with the law to ensure the safety and health of workers and others, and to ensure the quality of the project. We hereby make the following statement and commitment to your company regarding the quality and safety issues of this project:

1. Strictly implement national laws, regulations and normative documents on production safety and labor protection, and establish and improve safety production responsibilities system and on-site safety management system, and accept the supervision and inspection of administrative departments, general project contracting units, supervision units and your company.

2. Our company fully possesses the qualifications and conditions for the construction of this project. The construction methods or procedures comply with national, local and industry requirements. The construction personnel have legal qualifications and corresponding experience. The on-site construction facilities, materials and equipment It is a product of a regular domestic or foreign manufacturer and has relevant certificates of qualification. It has good mechanical properties and complete, sensitive and reliable safety protection devices. Ensure that advanced technology and advanced technology are actively adopted during the construction process.

3. Our company will fully pay attention to and ensure the safety of people and property at the construction site, strictly follow the safety production and civilized construction standards stipulated by the state and government, and do a good job in protection, and take

Effective measures such as protection and fencing, lighting, guards, guardrails, warnings, etc. will bear liability for compensation for personal or property damage caused to yourself, your company or others during the construction process.

4. The products supplied, produced or installed in your company's projects fully comply with the current national standards and the stipulations of the contract, and have no defects in raw materials, processes, production equipment and installation. This statement remains valid after the product is delivered or installed on the project, and shall not be invalidated by your company's acceptance of the product and payment of the price for the product. Implement the "lifelong system" of project quality and bear economic, administrative and criminal liability for safety accidents caused by construction projects within the quality and safety responsibility period determined by national law.

5. A rapid emergency response mechanism for engineering safety accidents has been established. We guarantee that when there are problems with project quality or safety hazards, effective measures will be taken immediately to remedy the situation, proactively or at your company's request, to eliminate safety hazards and protect the interests of your company and customers to the maximum extent possible.

6. If a major safety accident occurs due to project quality problems, our company will bear all losses caused to your company such as customer claims and reputational impact.

Party B (official seal):

Legal representative:

Supervision telephone number:

xx year, month and day

Quality Warranty

1. Warranty Scope: Party B is responsible for the warranty of all projects within the contract scope.

2. Quality warranty deposit: 5% of the total settlement price of this contract will be used as a quality deposit. After the expiration of the warranty period, Party A will confirm that there are no quality problems within 7 working days. Party A pays Party B a one-time payment, and the warranty deposit does not accrue interest.

3. Quality warranty period: detailed bidding points. If quality defects occur, the warranty period shall be extended, subject to the time determined by Party A.

IV. Warranty Responsibilities:

1. Party B must repair any quality defects that occur during the warranty period unconditionally, timely, and free of charge, and bear the responsibility for any damage caused to Party A and the house. Total loss.

2. Warranty quality must meet relevant national or industry standards.

3. Party A will bear the cost of repairs not caused by Party B, and Party B is obliged to cooperate with Party A to complete the repairs.

4. Party B promises to actively carry out maintenance outside the warranty period and only charges material cost.

5. Maintenance contact person: Party B shall determine the quality warranty contact person when the project is handed over, and his contact number shall be kept open 24 hours a day. Party A will only notify Party B's contact person by phone. If the contact number is changed during the warranty period, Party B shall notify Party A in advance.

6. If there is an emergency that affects the normal life of the residents, Party B shall rush to the scene within 2 hours; Party B shall make a decision within 1 hour after receiving the notice from Party A Respond and arrive at the scene within 4 hours; Party B shall complete the maintenance work within the reasonable period required by Party A.

5. If Party B encounters any of the following circumstances, Party A has the right to entrust a third party to perform maintenance and repairs on its behalf.

The resulting expenses, damages and related responsibilities shall be borne by Party B Responsibilities:

1. Although I rushed to the scene in time after receiving the maintenance notification from Party A, I was irresponsible or shirkable or failed to perform the maintenance during the maintenance process.

2. Failure to arrive at the site within the agreed time.

3. Arrive at the scene beyond the agreed time.

4. Cutting corners.

5. Failure to meet quality standards.

6. Exceeding the normal maintenance time.

7. Failure to fulfill commitments to Party A and residents.

8. The behavior of maintenance personnel caused complaints from owners.

6. For emergencies such as water leakage and electricity leakage due to project quality problems that affect the normal life of the owner,

Based on actual needs, Party A can arrange repairs on its own and notify Party B in a timely manner. , the relevant costs shall be borne by Party B.

7. National or industry-related quality warranty regulations.

Party B (official seal): Legal representative: Supervision phone number:

Year, month and day quality and safety commitment letter 4

In order to ensure the quality and safety of vegetables on the market, in The following commitments are made to the safe use of agricultural inputs in the vegetable production process:

1. Ensure that the inputs used in the vegetable production process comply with national standards and resolutely eliminate methamidophos and methyl, which are expressly prohibited by the state. The use of five highly toxic and high-residue pesticides, including parathion (methyl 1605), parathion (1605), monocrotophos, and ammonium phosphate, as well as other prohibited chemical substances.

2. Choose high-efficiency, low-toxicity, low-residue pesticides and strictly implement the safe interval between pesticide use.

3. In accordance with the principle of balanced fertilization, use organic fertilizer as the main fertilizer, apply base fertilizer more heavily, and apply top-dressing fertilizer sparingly and early. For leafy vegetables that are received at one time, it is guaranteed not to apply chemical nitrogen fertilizer 20 days before harvest.

4. Ensure that only registered pesticides such as 40 Thiabendazole wettable powder, 4.3 high fluorocyanine plus Avitamin emulsifiable concentrate are used in the production of edible fungi, and their use in post-harvest preservation of edible fungi is prohibited. Color-protecting agents, fluorescent whitening agents and other prohibited additives.

5. Establish a vegetable safety production record ledger, and record in detail the names, amounts and dates of agricultural inputs in each growth period of vegetables.

6. Ensure that vegetables are qualified for listing and trading. If you do not operate in accordance with the above commitments and a food poisoning incident occurs, you (the company) will bear all financial and legal responsibilities for the consequences.

Signature of the promisee (unit):

Year, month and day quality and safety commitment letter 5

Project name:

Project team Group:

Construction location:

Project planning period: year month day to year month day

Construction unit:

It is a strict project Management of safety, quality, progress, and cost, supervising the entire construction process, strictly controlling project quality, and ensuring the rights and obligations of both the construction unit and the construction unit. The following provisions are specially formulated, and the construction unit must strictly abide by them.

1. Before the start of the project, a start-up report and construction safety technical measures must be obtained. The project can only be started after it has been approved by the leaders in charge of the production department, safety supervision department, and center and reported to the manager for approval.

2. During the construction of the project, safety work on site must be carried out strictly in accordance with the requirements of safety technical measures. If construction does not follow the measures, the on-site person in charge of the construction unit has the right to stop the construction immediately and make rectifications within a time limit. Work can only be resumed after on-site inspection by relevant personnel until it is qualified.

3. Operators of special types of work must hold valid certificates issued by relevant units to work with certificates.

4. To enter key parts of the five pipes such as pools and pump rooms, you must have a letter of introduction issued by the center. (The letter of introduction must indicate the reason for entry, the name and provincial certificate number of the person entering, the name and contact information of the person in charge of the site)

5. When there is recycling of waste materials during project construction, the construction unit shall be responsible for recycling, and Return all materials to the construction unit, and the Central Material Supply Department will be responsible for unified recycling. The construction unit shall not dispose of them at will.

6. The person in charge of on-site safety of the construction party has the responsibility to check the safety of the construction site and rectify any hidden dangers immediately if any.

7. The team and construction site representatives have the right to promptly require the construction unit to make rectifications within a time limit for safety and quality problems existing during the construction process, otherwise they have the right to stop the construction. All consequences shall be borne by the construction unit itself.

8. After the above matters are approved by both parties, they will be signed and sealed to take effect.

Construction unit: Construction unit:

On-site construction leader: Site representative:

Contact information:

Signing time: Year Month Date Quality and Safety Commitment Chapter 6

On September 1, XX, the company's production department promoted the quality service system and promised to bear the responsibility for quality problems if the following problems occur during the advertising construction and during the use period. related liabilities and financial compensation caused.

1. Due to the construction quality and the falling off of the billboard, the structure of the billboard is damaged, causing damage to the human body and public property.

2. Improper handling of the construction site or improper protection of the waterproof layer will cause leakage in the house and cause economic losses to Party A.

3. Unsafe installation of advertising cards and light boxes can lead to electrical failures, resulting in personal and other damages.

4. During the construction process, construction personnel did not manage well and violated regulations causing losses.

5. During the warranty period, Party A will notify the billboard of repairs and ensure that the treatment is completed within 48 hours.

This commitment letter is an attachment to the production contract. If there is any conflict between the contents of the commitment letter and the terms of the contract, the terms of the commitment letter shall prevail. This commitment letter and contract are legally binding and will come into effect upon signature and seal. The project and overall safety are guaranteed for two years.

Pledger:

Date: Year, Month, Day Quality and Safety Commitment Part 7

Name of construction unit: ____________________________

Name of project ：____________________________

Name of construction unit: ____________________________

Construction start time: ___ year ___ month ___ completion time: ___ year ___ month ___ day project Content: ____________________________________________

____________________________________________________________

Our unit solemnly declares: As of the date of application for the construction license for the above-mentioned projects, all the projects built by our unit have not been in arrears with project payments. . Our company promises to pay the construction fee for the project in accordance with the construction contract between the two parties. If the project payment is not paid in time and in full according to the construction contract, or if our unit illegally contracts the project business, resulting in disputes over the arrears of project payment or worker wages for the project, our unit is willing to accept the resolution of the construction administrative department in accordance with relevant regulations. handle everything and bear corresponding legal responsibilities. Quality and Safety Commitment Part 8

If our unit is lucky enough to win the bid for the Aksu Economic and Technological Development Zone Expressway Ramp Greening Project (BT Project), we will do our best to ensure the quality of the project (construction period, safety) during the implementation of the project. The following commitments are made:

1. Construction period: The construction period shall be completed within 60 calendar days specified by Party A (March 17-May 17, 20xx) to ensure scientific construction. Organize and complete reasonable measures, implement progress management, and fully manage other coordination processes and construction progress. Solve the factors that delay the construction schedule in a timely manner and ensure that the construction is completed on time.

2. Quality: According to the drawing design and Party A’s requirements, strict quality control is required to ensure that the quality is qualified.

3. Safety: No major liability accidents and no personal casualties.

Bidder: (official seal) XXXXX Co., Ltd.

Legal representative or authorized agent (signature and seal)

Date: June 14, 20xx Quality and Safety Commitment Chapter 9

1. Strictly establish and improve business files and implement purchase and sales ledger records;

2. Purchase goods from legal production enterprises and control the quality of purchased goods;

3. Do not deal in agricultural inputs banned by the state or fake and inferior agricultural inputs;

4. Introduce scientific, reasonable and safe usage knowledge to buyers;

5. Bear legal liability for safety accidents directly caused by the agricultural inputs sold by itself.

(This letter of commitment is made in 2 copies. One copy is deposited with the County Agricultural Bureau; one copy is promised to be kept by myself)

Promisor:

April 20xx 20-Day Quality and Safety Commitment Part 10

Our company () has had no breach of contract in the past three years, no bad reports, no arrears of wages to migrant workers, and no fraud in the past three years

Problems such as winning bids, serious breach of contract or major project quality and safety production accidents. Our company promises: If the above content is false

Our company and the staff participating in the bidding are willing to accept penalties in accordance with national laws and regulations and other relevant provisions.

(Official seal of the bidding unit) June 27, 20xx

Project Manager Commitment Letter

Our company solemnly promises:

In Jun During the construction of the river management project in the county's Junnei River City area

, our company guarantees to do the following:

1. Participate in this bidding activity with fair competition.

2. If our company wins the bid, the project manager proposed in the bidding document will guarantee to work on-site on legal working days every month, and other members of the project department will guarantee to carry out construction management on-site during the construction period, without any prior approval from the owner. If allowed, the project manager and management personnel may not be replaced, otherwise the entire performance bond will be deducted, and the owner has the right to unilaterally terminate the contract, and the contractor will be responsible for all losses caused thereby.

Project manager (signature):

(Official seal of the bidding unit) June 27, 20xx