Newly bought apple 5s. How to charge the battery? For example, you can't play while charging. It's best not to charge the battery when it runs out. Wait a minute. Tell me. Don't want electricity

1. Develop good habits, don't wait until there is no electricity to recharge, and don't continuously overcharge for a long time. Li-ion likes shallow charging and shallow discharging. Of course, it is very difficult for an ordinary user to always remember when to charge or turn off the software and other power-saving operations. 2 After the "fast charge" stage is completed, in fact, the charge is just about 80%, and there is still a lot of charging space for the battery; In fact, lithium-ion batteries have two processes of "continuous charging" and "trickle charging", which can be monitored by third-party battery management software to make it play a greater role at critical moments. In fact, it can also save electricity by forming a good habit of using electricity and closing some unnecessary software in time. For example, turning off devices such as WiFi and Bluetooth without a network can also extend the standby time. Many times, when the mobile phone prompts that the power is low, the power is often quite low. If it continues to be used, it is easy to cause excessive discharge, which has a great impact on battery life. Jinshan battery doctor can customize the low battery reminder and switch the power saving mode intelligently. Nowadays, almost all mobile phones use lithium-ion batteries, which have no memory effect, and need not be recharged for 12 hours. In addition, excessive charge and discharge of lithium-ion batteries will cause permanent damage to the positive and negative electrodes of the batteries. Overcharging makes too many lithium ions embedded in the negative carbon structure, and some of them can't be released, which shortens the battery life and also has potential safety hazards. The whole process of mobile phone battery charging includes three stages: fast charging, continuous charging and trickle charging. After the first two stages, although the system power showed 100%, the battery did not really reach saturation. At this time, the remaining capacity can only be supplemented by tiny pulse current, which usually takes 30-40 minutes. Only when these three stages are completed can the battery really reach a good saturation state. In order to prevent accidents caused by users' overcharge, the design of overcharge protection circuit is adopted for mobile phone batteries, that is, the charging process will be automatically terminated after charging is completed. However, the battery will start the self-discharge process at the same time, resulting in a decrease in power; After the power drops to a certain extent, it starts charging again and repeats the discharge-charge cycle. However, long-term exposure to high voltage will have a negative impact on the battery, resulting in crystal precipitation and adhesion, which not only shortens the battery life, but also has potential safety hazards. The behavior of using a mobile phone while charging will do harm to the mobile phone, people and batteries. Because the voltage of the mobile phone battery is higher when charging than when it is in standby, if you answer and make a phone call at the same time, the instantaneous voltage of talking or connecting to the network will be many times higher than usual, which will lead to the failure of the mobile phone. Secondly, the radiation of the mobile phone is higher than usual when charging. Use your mobile phone as little as possible when charging. In addition, there is no need to worry about multiple interruptions in the charging of lithium-ion batteries. Therefore, when you need to make a phone call or play a game, you can disconnect the power. Normal use is enough, but don't charge in a bad charging environment. Unstable voltage will damage the battery. Lithium batteries have no memory, like to charge and discharge lightly, and can be charged at any time. However, if the battery cannot be fully charged involuntarily, it is likely that there is something wrong with the charger or the battery itself. It is recommended to send it for repair or replacement in time to avoid danger. Although the charger of iPad is compatible with iPhone, it is best not to mix them. After all, the iPad's charging adapter can provide a relatively large amount of power, which may cause damage to the mobile phone battery in extreme cases. General factory charger, nominal output voltage DC+5V, output current1a; ; The standard output voltage of USB port of general PC is 5V, and the output current is 500mA. According to these data, as long as the computer is well grounded and the USB interface has no quality problems, it is completely feasible to charge with USB data cable, but the theoretical charging time is 1 times longer than that of the charger, which is just "slow charging".