Key points of safety inspection and data inspection on construction site?

1. Key points of safety inspection on the construction site

1. Site fence: closed with hard materials or brick masonry (the wall height of the main road section in the urban area is 2.5m, and that of the general road section is 1.8m. ) wall plastering and whitewashing, so as to be firm, smooth, neat and beautiful. Brick enclosure should have a wall cap, and the wall should have propaganda slogans. Materials or soil are not allowed to be piled up against the wall. Color pressed steel plates can be used if conditions permit.

2. Gate of the construction site: there are battlements and gates. There is a light box at the top of the door with the name of the enterprise and the name of the project. The guard room should have a guard system. At the gate, "Construction is important, no idle people are allowed to enter." And "safety helmet must be worn on the construction site." Brand. There are seven pictures and three cards hanging in the door.

3. Site floor: hard floor with good drainage (the main road in the hardened site is not less than 2m, and it is not less than 5m outside the site) and equipped with a washing table.

4. personal protection: wear a safety helmet and fasten your seat belt. the seat belt should be hung high and used low. the "three treasures" must have production license, product certificate and quality inspection certificate.

5. On-site access: a protective shed is set up at the entrance of the access, the shed is wider than the crossing, and the top of the shed is covered with scaffolding. The shed length should be greater than 3m; A building with a height of more than 24m shall be provided with double protection, with an interval of not less than 6㎝ and a shed length of more than 1m.

6. elevator wellhead: a fixed gate fence or a double-way fence with a height of not less than 1.2m (one for 6㎝ and one for 12㎝) shall be set, and a flat net shall be set every 1m in the elevator room.

7. limb protection: balcony, roof, floor, stairs, unloading platform and other limb facilities shall be provided with two protective fences with a height of 6㎝ and 12㎝ respectively, and columns shall be set up with a spacing greater than 2m.

8. scaffolding: it is forbidden to mix steel and wood in material selection, and the material meets the standard. It is not allowed to dig the foundation on the side until the scaffolding is dismantled.

9. reserved openings: openings larger than 25㎝ are protected by fixed cover plates, and openings larger than 5㎝ are surrounded by two horizontal railings with a height of not less than 1m. In addition to two horizontal railings, a safety flat net must be set up below the hole with a hole greater than 1m.

1. Dangerous areas: Danger signs such as "No" and "Warning" should be hung in the dangerous areas at the site.

11. Material stacking: classified and stored neatly, marked, and provided with a site plan.

12. storage of gas cylinders: oxygen cylinders and acetylene cylinders are more than 5m apart, and 1m away from open flames, so they cannot be exposed to the sun, and acetylene cylinders cannot be laid flat.

13. Construction pit (trench): When the depth of the pit (trench) is more than 1.5m, slope or reliable support must be added; when the depth is more than 2m, two guardrails with a height of 1.2m must be set around, and the distance between vertical poles should not be more than 2m. The upper and lower passages should be erected stably and non-slip. No soil, materials or machinery are allowed to be piled up within 1m of the pit (trench).

14. Project license: business license (original copy), enterprise qualification (original copy), safety license (original copy), safety qualification certificates of enterprise legal person, safety leader in charge and person in charge of enterprise safety, safety management network diagram, safety production guarantee system, safety production responsibility system at all levels, safety production responsibility certificate (signed step by step until workers), qualification certificate of full-time safety officer in the project department, and post status, and safety officer of the team.

15. On-site fire prevention: The floors of carpentry room, canteen, dormitory area and operation area must be equipped with fire-fighting equipment, and signs of no smoking fire are hung in dangerous places.

16. Life logistics: No people are allowed to live in the project under construction, urinals are set in high-rise buildings, it is forbidden to urinate anywhere, and clothes are not allowed to hang on scaffolding or wires. On-site canteens should comply with regulations, operators should have physical examination health certificates, raw and cooked foods should be separated, and canteens should have screen windows, screen doors, gauze covers, hygiene licenses and hygiene responsibility systems.

2. Key points of enterprise safety data inspection

1. Enterprise safety production license (original and copy);

2. enterprise safety production management responsibility system;

3. Rules and regulations of enterprise safety production;

4. enterprise safety production operation procedures;

5. The leading group, organization and staffing of enterprise safety production management;

6 .. safety assessment related materials of "three types of personnel";

7. List and management of special operators;

8. proof of risk of mortgage's payment for enterprise safety production;

9. Pay relevant materials for industrial injury insurance and accidental injury insurance;

1. Safety production input list and related bills;

11. Special construction plan approval and expert argumentation data;

12. enterprise safety production education and training files and related materials;

13. enterprise safety inspection data;

14. Emergency rescue plan for production safety accidents of enterprises and relevant records of drills;

15. Enterprise production accident account and accident related information;

16. mechanical equipment management information;

17. Relevant information on the management of subcontractors and suppliers by enterprises;

18. Relevant information on labor protection articles management and occupational disease prevention and control;

19. Relevant information on identification, evaluation and control of hazard sources;

2. Relevant information on the implementation of documents and notices issued by the competent authorities and formulated by enterprises themselves;

21. Other relevant information.

III. Key points of on-site safety data inspection

22. Copy of enterprise safety production license, copy of assessment certificate of enterprise legal person, enterprise manager, production manager, safety department (division) chief, project manager and project full-time safety officer;

23. enterprise safety management rules and regulations;

24. Operating procedures for each type of work;

25. Monthly report of employee casualties, industrial accident registration form, some related records of industrial accidents, statistical account of accidents and events, industrial accident reports, industrial accident files and industrial accident handling records;

26. Handle the relevant documents of accidental injury;

27. Copy of on-site safety investment account and shopping documents;

28. Safety production education and training, annual training plan for employees, list of trainees, training account and training records;

29. Record cards of three-level safety education for new workers, records of educational contents, and examination papers of division of labor;

3. List of special operators and copies of special operation certificates;

31. Construction organization design and special construction scheme;

32. Scheme of expert argumentation review and argumentation review report

3. Safety sign plan and drainage plan;

34. List of major hazard sources on the construction site;

35. Safety inspection records;

36. Notice of potential accidents;

37. Organization design, safety technical disclosure and acceptance record of temporary electricity utilization;

38. grounding resistance test record, leakage protector test record and electrician patrol record;

39. "Three treasures" and "four ports" protection, safety helmet, safety belt, safety net certificate and test report;

4. Safety technical disclosure and acceptance records;

41. Foundation pit supporting scheme, safety technical disclosure, acceptance records, monitoring or observation records;

42. scaffolding construction scheme, erection safety technical disclosure, acceptance record (hierarchical acceptance), demolition safety technical disclosure;

43. formwork engineering construction scheme, safety technical disclosure for erection, formwork acceptance record (layered acceptance), concrete strength report, and safety technical disclosure for formwork removal;

44. Special construction scheme of tower crane, safety technical disclosure of installation, acceptance record and safety technical disclosure of demolition;

45. Safety technical disclosure, acceptance records and maintenance records of construction machines and tools;

46. Lifting construction scheme, safety technical disclosure and acceptance records;

47. Construction scheme, safety technical disclosure and acceptance record of material hoist;

48. External elevator installation scheme, safety technical disclosure, acceptance record, inspection record and demolition safety technical disclosure;

49. On-site emergency plan, emergency drill record and emergency situation (accident) handling record;

5. Procurement plan, distribution account, certificate of approval and test report (or record) of labor insurance supplies;

The above are collected and sorted by Zhongda Consulting.

For more information about engineering/service/procurement, please click on official website Customer Service at the bottom for free consultation:/#/? source=bdzd