Safety self-inspection and self-inspection report selected examples

Strengthening the prior control and management of production safety and eliminating hidden dangers in a timely manner are necessary conditions for ensuring the stable development of an enterprise's production safety. The following is a sample safety self-examination report that I compiled for everyone, for reference only.

Safety Self-inspection and Self-inspection Report Sample 1

In order to ensure the fire prevention and anti-theft safety of our company’s office environment, according to the arrangements of the company leaders, the person in charge of the comprehensive office led the relevant office personnel A safety inspection team was formed and conducted a strict inspection on the fire safety and anti-theft work of the company's office building and the open-air parking lot downstairs on the afternoon of December 12. The inspection results are now reported as follows:

1. Safety Inspecting the overall situation

The inspection team first inspected the doors and windows, electrical circuits and switches, corridor fire safety passages, fire protection facilities, environmental sanitation, etc. on each floor of the office building. Then the open-air parking lot, green belt and lighting facilities outside the building were inspected.

The inspection team conducted a comprehensive inspection and found that the overall situation was good and there were no major safety hazards.

2. Problems

1. The doors leading to the terrace on both sides of the fifth floor roof are not locked, and the door of the fourth floor conference room and an aluminum window in the conference room are not locked. The door lock on the right side of the sliding door of the reading room cannot be locked, and the door lock on the right side of the sliding door of the reading room is damaged. Outsiders can enter and exit at will, which poses a safety hazard.

2. There are piles of debris in the reading room, which are piled up in a messy manner, posing fire safety hazards.

3. The entire building is equipped with only 2 dry powder fire extinguishers, and the shelf life of the dry powder in the fire extinguishers is unknown; the fire hydrants on each floor are locked, but the keys are missing, and there is no way to check whether the fire hydrants can be used. Normal use. There are fire safety hazards.

4. Some offices on the second floor do not lock their doors after get off work, posing potential security risks against theft.

3. Corrective measures and suggestions

1. Ask a professional locksmith to install new locks for the doors leading to the terrace on both sides of the roof on the fifth floor, and for the doors and windows of the conference room and reading room on the fourth floor. The doors and fire hydrants on each floor will be replaced with new locks.

2. Classify and organize the reading rooms in accordance with the "6S" management standards to eliminate fire safety hazards.

3. Replace and purchase dry powder fire extinguishers as needed, and review the safety status of fire hydrants on each floor after replacing them with new locks.

4. Once again emphasize the requirement that the doors and windows of offices on each floor must be locked after get off work. In response to the safety hazards discovered during the inspection, the inspection team will contact relevant personnel to make timely rectifications to ensure that there are no blind spots in fire safety and no loopholes in anti-theft security, so as to create a stable and safe working and living environment for the company's employees. Safety self-inspection and self-inspection report sample article 2

Continue to carry out in-depth publicity and education activities for the "Safety Production Month" activity. According to the document requirements, our project department carried out self-inspection and self-correction activities. Through self-inspection, the safety inspection The problems existing in production management are summarized as follows:

1. Safety organization management

1. Safety production management organization

2. Safety Supervision Management Measures

3. Safety Management Emergency Plan

In accordance with the requirements, we divided the management responsibilities within the scope of the project department, clearly defined the management boundaries for some dual management parts, and eliminated dead ends. By decomposing and implementing it into people, combined with the safety contracts of their respective positions, daily inspections and management can be carried out to reduce the occurrence of accidents.

2. Basic management work

1. The project department firmly establishes the policy of “safety first, prevention first, comprehensive management”, strengthens leadership, enhances its own sense of safety responsibility, and truly Implement safe production.

2. Carefully study laws, regulations and relevant provisions, further implement the safety responsibility system at all levels, do a good job in safety disclosure of each project, strictly implement safety operating procedures, and increase safety production education and training for workers , to further improve the standardization of safety management information.

3. Establish and implement a work-related injury insurance system. The project department handles work-related injury insurance for supervisors, organically combines work insurance with construction safety management, and further improves the safety of employees.

3. Safety supervision and management

1. Safety data management

Safety data is the focus of safety production supervision and management. The project department requires the construction unit to start every project Submit the safe construction notice and dangerous operation application form before the start of construction, and bring the dangerous operation application form with you on the day of the start of construction to check whether the on-site construction personnel are consistent with the reported materials, and sign and file after verifying the materials.

2. Construction site management

The construction site is the top priority of safety production supervision and management. Eliminating on-site hidden dangers and improving prevention capabilities are the foundation for doing a good job in safety work, so here During this event, we combined special rectification work, paid close attention to on-site organizational leadership and system implementation, investigated signs of various accidents, and implemented on-site protective measures. Focus on special management: focus on prevention and monitoring of construction sites that may cause construction collapse, scaffolding overturning, wall collapse and other accidents that may easily lead to mass deaths and injuries, as well as demolition operations, hoisting operations, overhead operations and other construction sites. Strengthen safety management of external construction workers. The project department strengthens the safety education, supervision and inspection of external construction teams, promptly discovers and corrects illegal operations and disciplinary behaviors, and resolutely reports teams that seriously violate rules and disciplines and requires them to rectify.

This "Safety Production Month" activity has achieved some results in enhancing the awareness of production safety among all employees, promoting the safety production management of construction projects in the project department, and improving the level of safety protection at the construction site. However, we are also clearly aware that there are still many problems and weak links in the safety production management of construction projects in the project department. In future work, we must increase management efforts, work hard, strive to improve the overall management level, and focus on Do the following:

1. Consolidate, develop, and improve the results of the "Safety Production Month", make a fuss about long-term management, and strive to achieve the annual safety work goals.

2. Further strengthen the improvement of ideological understanding, especially the improvement of the ideological understanding of the person with the first responsibility for safety. Supervise construction units to further improve their safety organizational structure, equip them with professional safety personnel, improve various safety management systems, and implement the safety production responsibility system.

3. Conscientiously implement the "Regulations on Production Safety Management of Construction Projects", further implement the responsibility for supervision of production safety, and form a good situation of joint management.

4. Continue to strengthen safety supervision and management to prevent vicious accidents that cause mass deaths and injuries. For engineering projects with poor safety management, we must rectify and improve them. If the rectification is not in place and the appearance does not change, we must not let go.

In future work, the project department will continue to consolidate the results. In the second half of the year, it will strengthen safety production management, implement various safety responsibility systems, strengthen civilized construction and safety supervision at the construction site, and strive to achieve this year's safety production goals. Safety self-inspection and self-inspection report sample article three

In order to thoroughly implement the spirit of the instructions of the Jilin Provincial Department of Housing and Urban-Rural Development on the "Emergency Notice on Further Strengthening the Safety Production of Urban Municipal Public Utilities and Construction Construction", we must deeply learn Learn from the accident, implement safety responsibilities, strengthen preventive measures, do a good job in the company's production safety work, effectively prevent and resolutely curb the occurrence of accidents, the company's production safety committee follows the requirements of the "Emergency Notice on Further Strengthening Production Safety in Urban Municipal Public Utilities Industry and Construction Construction" , inspect the implementation of safety responsibilities and systems, safety publicity, education and training, implementation of safety responsibilities and rectification of hidden dangers, and emergency plan formulation and drills. The specific self-examination contents are as follows:

1. Implementation of safety systems and responsibilities

The company’s production safety management system filing and archiving work is complete, each system is sound, the emergency plan is complete, and drills are feasible , the assessment results of various operating procedures are good, cadres and workers at all levels consciously abide by the system and procedures, and there are no violations.

Each project department signed the "Team Leader Safety Production Responsibility Letter" with the front-line production team leaders. The team leaders have a strong awareness of production safety and earnestly implement the idea of ??"everyone is responsible for production safety" , employees conscientiously perform their respective safety production responsibilities in their positions, providing a strong guarantee for the implementation of various safety production measures.

2. Safety education and training

The company organized and carried out various forms of educational activities according to the overall arrangements of superior leaders.

The first is to carry out in-depth legal education and publicize and learn the "Safety Production Law" and other laws and regulations through holding safety production meetings and other forms. The second is to enrich the form of publicity activities by organizing employees to conduct safety knowledge education, and using bulletin boards, banners, slogans, etc. to promote various safety knowledge and safety regulations. It enables the majority of employees to have an in-depth understanding of safety and pay extensive attention to safety, which greatly improves the safety production awareness of all employees.

Through various forms (warning signs, publicity boards, slogans, etc.), employees can understand the hazards and preventive measures in their positions, and clarify the rescue measures when hazards occur. Educate employees on emergency response skills for minor work-related injuries to minimize injuries. Enable employees to skillfully use labor hygiene protective equipment, reduce occupational disease hazards, and prevent the occurrence of occupational diseases. Enable employees to take self-rescue and mutual rescue measures correctly and skillfully in emergencies. The company *** has organized many safety production knowledge trainings, and often holds safety production meetings to summarize the hidden dangers in safety production, formulate rectification and preventive measures for existing safety hazards, exchange safety work experience, and convey safety production documents. Arrange relevant safety work and report safety inspection status.

3. The "three types of personnel" and special operations personnel at the construction site must hold valid certificates to work, and the certificates must be consistent. The mechanical equipment such as tower cranes and construction lifts have been re-inspected and passed the inspection.

4. Implementation of safety responsibilities and rectification of hidden dangers

The maintenance records of equipment, safety protection devices, loading platforms, guardrails, scaffolding and other protective facilities are complete and effective. Various safety fire-fighting facilities are fully equipped, qualified and effective, and operators wear labor protection equipment in accordance with regulations.

The installation and maintenance of electrical equipment are operated by electricians. Non-electricians are not allowed to decorate electrical equipment and lines. There are dedicated personnel to manage accident-prone electrical equipment, and everyone is responsible. Electricians must be equipped with labor protection supplies as required when working, work according to operating procedures, and regularly check circuits and all electrical equipment. Protective facilities and warning signs are set up in all high-voltage dangerous places. Non-electricians are strictly prohibited from entering power distribution rooms or It is strictly prohibited to pull or hang the electrical equipment inside the guardrail, and it is strictly prohibited to approach high-voltage dangerous places.

In accordance with the requirements, members of the Safety Production Committee carried out multiple safety production inspections in stages. We made rectification and treatment plans for various hidden dangers that were detected, and truly eliminated the hidden dangers of accidents. Conduct a self-examination every month. During the inspection process, we adhered to the principle of "safety first, prevention first, and comprehensive management", and carefully conducted comprehensive inspections on weak links and possible problems, focusing on whether the safety system was implemented, whether safety measures were in place, and whether safety protection facilities were in place. Whether the equipment is complete and intact, and whether the hidden dangers have been corrected.

5. Emergency plan formulation and drills

In order to prevent the occurrence of emergencies, the company’s production safety committee team has conducted several emergency accident plan studies for department employees. On the basis of learning, we simulated emergency safety accident drills and fire firefighting drills based on the particularity of the unit's production. The drill focused on examining employees' ability to respond to emergencies, investigation and handling of emergencies, and personnel self-protection measures. Through on-site emergency plan drills, the safety awareness of employees and managers is improved, so that employees clearly understand the importance of safety in production, enhance employees' ability to respond to emergencies, gradually improve and improve emergency rescue plans, and improve employees' Emergency response and on-site rescue skills.

6. During the inspection, some individual safety hazards were found, and the company ordered the project department

to make immediate rectifications

1.

2.

3.

4.

Signature of the construction unit: >>> More "Safety Self-inspection and Self-inspection Report Sample" on the next page