Typical speech on power safety production

Typical speech on power safety production

In our daily life and work, speech plays an increasingly important role. Speech can improve the self-confidence of speakers and help them to show themselves better. So, how to write a speech? The following is my typical speech on power safety production, which is for reference only and I hope it will help you.

Typical Speech on Safe Production of Electric Power 1 20xx 1 12. On February 8th, Lu Fang Center Power Supply Company of Jinxi Power Supply Company took the Safety Day as an opportunity to actively study accident cases. Our institute attached great importance to the study of each accident case, and all staff actively participated in it, carefully studied every accident around us and analyzed various reasons for the accident.

First of all, everyone thinks that we should attach great importance to safety ideologically, treat everything well, and do everything with our heart. Chairman Mao once said: "The word' earnest' is the most frightening word in the world. As long as you are serious, there will be no bad things in the world, and there will be no such accidents. As long as you take responsibility for everything, have a correct attitude, be strict with yourself everywhere, always alert yourself in your daily work, and believe that everything can be done well.

Secondly, as our power production work, safety is the top priority of all work. Therefore, we must strictly abide by the rules and regulations and operating procedures, and we must not violate the operating procedures just because we are familiar with them and have never done anything wrong before. 5 "and" 1. The illegal operation of "February 28th" is a vivid example. We will definitely take the lesson of their blood as the lesson of our future work and carefully analyze the direct and indirect causes of their accidents. Strengthen the safety management of our company, and put an end to illegal management and illegal behavior accidents.

Third, on-site operation must be supervised by special personnel. The person in charge of the work shall take full responsibility and operate according to the safety measures indicated on the working ticket. We can't be like them, because we are afraid of trouble, we don't do work tickets, we don't check electricity, and we don't hang ground wires. Because I relax myself, even the grounding wires will be hung in the wrong order. I must follow the electric power safety operation rules and do a good job in large-scale construction and small-scale emergency repair and maintenance. In particular, our usual elimination of defects cannot be taken lightly.

Fourth, conduct regular safety training, arm the brain with knowledge, integrate theory with practice, and let everyone know the use and operation of safety tools and instruments. Don't go to the real field, one is the first two, and you don't understand anything when you use it.

In short, learning accident cases is by no means an armchair strategist, nor is it formalism. Instead, we should keep the lessons of others in mind and always spur our daily behavior. Get into the good habit of touching your head at the construction site and see if you are wearing all the safety tools under your feet. Let the word "safety" always be deeply stationed in everyone's heart. Do every job carefully, come to work happily and go home safely.

The electric power industry is a dangerous job, but as long as we master the law of electric power operation, always keep the vigilance of safe production, prevent delays, and take every task seriously, we can completely tame the "electric tiger". The "safety regulations" and various safety measures in our hands are layers of cages and shackles designed for this vicious "electric tiger". This accident is precisely because the people involved in the work are careless about the tamed electric tiger, thinking that the electric tiger who has been arrogant for many years has really become a "sick cat". The danger of power system operation and maintenance is simply ignored, which is tantamount to opening the cage and shackles of "electric tiger" without authorization. This vicious "electric tiger" certainly won't miss any opportunity to show off.

Through research, I mainly have the following points:

1, safe production is not a slogan.

Safety in production is an epigram that we electric workers can hear or see all the time. But this is not only a slogan, but also the first criterion of our work and the only measure to ensure our personal safety. We can't ignore the danger of the future because of the previous safety. Forgetting this rule is to send yourself into the cage of an "electric tiger" with ingredients.

2, obey the command, obey the scheduling

Without all kinds of safety measures, the danger of electric power work is far greater than war. Because not everyone will die in the war, and if there is no guarantee of safety production measures in power production, no one can escape the clutches of the "electric tiger". Without strategic planning and flexible command and coordination of all arms and units, the war will fail. The same is true for electric power work. If there is no safety production measures as a weapon, if there is no strict command, it is very likely to cause self-injury, accidental injury, and even mass casualties, and at the same time cause immeasurable economic losses. No less than losing a war. Therefore, electric power work should be as disciplined and well-directed as the army.

3. The laws are not complied with and the law enforcement is lax.

With the promulgation of the Law on Safety in Production, safety in production has risen to the height of law. Yes, if you don't abide by the safety production guidelines personally, the consequences may be harm to others. This is "homicide"! It may also cause national economic losses, which is the crime of endangering national security! Even if there are no serious consequences, you have committed the crime of dereliction of duty. If the safety measures in our work, such as "two votes and three systems", are not strictly observed by the staff, but go through the formalities, that is, "the law is not complied with and the law enforcement is not strict." It is a threat to personal safety and state property, and it is a crime. "Bengbu No.5 Middle School. In the "12" accident, there were "signed" and "unsigned" work tickets, and the system of work interruption and signature handover was not strictly implemented, that is, the compliance with the safety production guarantee system was not raised to the level of legal compliance.

In the future, I will be strict with myself, earnestly abide by various safety guarantee systems, perform the duties of safety production, earnestly abide by the safety guarantee measures such as "two votes and three systems", and never be careless. For the happiness of my family and the prosperity of my career, I will cherish the precious lives of myself and others.

A typical speech on power safety production: a personal electric shock accident occurred in a substation in xx power transmission and transformation work area of xx Power Bureau. In view of this accident, our substation maintenance class conducted serious study and discussion.

After investigation, the work of the accident itself is very simple, that is, to pre-test the switches, ct and line coupling capacitors at interval 226 of 66kv tower line. However, our staff did not strictly abide by the relevant provisions of the safety regulations, which led to the accident. Then, we talk about "safety first, prevention first" every day, and hold the "safety regulations" exam every year. Why did such a serious accident happen? I think there are two main reasons: first, safety management is a mere formality, and some staff members have a poor sense of safety responsibility, which often leads to the phenomenon of "not being on duty"; Second, the safety technical training is not in place, and some staff members have no real safety awareness and lack self-protection awareness.

The nature of the accident is bad, the consequences are serious, and the lesson is painful! In xx Electric Power Bureau, when there was no personal electric shock accident for more than 20 years, when the safety awareness of many managers and staff gradually faded, the accident undoubtedly gave us a blow! This stick woke us up: "Ah, the danger is around us!" " Mr. Wang said: There is a problem in our work, that is, the awareness of safety is weak-"accidents don't count unless they happen in our unit, and major accidents don't count!" I think Mr. Wang is right and practical.

As the saying goes, "It's not too late to mend." In my opinion, this sentence is not suitable for our electric power department! We don't want to "make up for it", but "prepare for a rainy day"! Nip in the bud and nip all unsafe factors in the bud!

Because the accident happened to a newcomer in the inspection and reform class, and I am a novice who has just stepped into the inspection and reform work, I feel extremely sad and sorry for the accident! If I want to talk about my feelings about the cause of this accident from the perspective of a newcomer to the inspection, and recall my previous work, plus this accident, I think there are two misunderstandings in our work: First, as a newcomer who has just joined the work, I still don't understand a lot of knowledge, but sometimes I am embarrassed to ask the old worker master because of my face. Second, on the other hand, because they have just joined the work, all parties are eager to show themselves and get everyone's recognition, but they are afraid of being accused, thinking that they are joking and being looked down upon by others. So no matter what work, as long as it is assigned by the masters, we will work hard and try our best to finish it as quickly as possible. Sometimes, I don't even wait for others to speak or say hello. I think only in this way can I show my positive work and vision.

In the face of painful accident lessons, I deeply realized how important it is for a new worker to be down-to-earth and diligent! In the work, we should actively carry forward the spirit of Confucius' "not ashamed to ask questions" and "three people must have a teacher" and be diligent in learning and consulting all aspects of working knowledge; Moreover, before taking part in some work, you should actively communicate with the master, especially when working on high-voltage equipment, you should ask the live parts and personally check whether the switch and breaker are in the open state. Remember that "face is small, work is big!" ""low speed, high completion! " "Anyway, safety first! " .

Through careful reflection on the accident, combined with the usual work, from the perspective of a newcomer, I have some immature suggestions:

First, because everyone has their own way of working, in order to adapt to the inspection work better and faster, can we arrange a relatively fixed partner for the newcomers who have just joined the work? In this way, newcomers can adapt to the working style of this fixed partner as soon as possible, and avoid misunderstanding and mutual distrust in information transmission and acceptance caused by unfamiliarity at work. Old masters take young apprentices, and this "one-on-one" working mode can also enable old masters to impart their work experience to newcomers better and more completely.

Second, can we find some teachers to train us regularly, so that we can have a more systematic and scientific understanding of the inspection work. In particular, give lectures on safety knowledge to new employees, increase safety knowledge and strengthen self-protection awareness.

Third, go to other places with good working methods and work experience from time to time to learn from each other. "Develop and strengthen yourself through continuous communication and learning.

Fourth, consolidate and improve our standardized operations and coordinate mutually beneficial cooperation between operation and maintenance. "Without rules, there would be no Fiona Fang." Only by doing a good job seriously can we ensure that the work is foolproof.

;