What should I do if the cartridge of Canon mp288 printer is unrecognizable?

What should I do if the cartridge of Canon mp288 printer is unrecognizable?

At present, the identification of the original ink cartridge is carried out by reading the chip on the ink cartridge. If there is poor contact between the contacts on the printer and the ink cartridge chip, the ink cartridge may not be recognized. The following is my unrecognizable solution to Canon mp288 printer cartridge, I hope it will help you!

Canon mp288 printer cartridge can't recognize 1. What should I do?

Problem 1: The ink is blocked and cannot be output normally.

Although the price of printers has fallen into the era of low prices, it is undeniable that the technical content of this industry is still very high, especially the core technologies in the fields of ink and printing are still in the hands of a few manufacturers. Because there is no core technology of modification and continuous supply, the quality of ink can't be guaranteed, which leads to more impurities in the use of ink, and because the use environment is in an open state, dust falls in and the ink volatilizes, which eventually leads to ink deterioration. At the same time, the dissolved bubbles in the ink will also cause the print head to be blocked, leading to various problems.

In addition, because the modified printer is often plugged in and out, after repeated maintenance, the ink cartridge will not be recognized by the printer and the decoding chip will not be decoded. Only professional decoding software can be used for soft decoding, or the chip can be replaced in the repair shop, which greatly reduces the use efficiency of the modified continuous supplier and affects the working mood of users.

Problem 2: the ink pressure is unstable, and the ink leakage is serious.

After using this device, I found that the printed pattern was a little off-center and the color was dark. Sometimes the printed proofs are still insufficient in color, and there are big ink drops on the proofs, which leads to the rejection of the manuscript and can only be reprinted. Mr. Li, who just used a modified continuous supply printer, said. The above situation is closely related to the unstable ink supply pressure of the modified continuous ink supply machine.

As we all know, it is necessary to manually adjust the height of the ink cartridge to maintain the balance of ink supply pressure when modifying the ink supply amount of the continuous ink feeder. Therefore, in daily use, users often encounter ink overflow due to excessive supply pressure, which leads to printing failure and pollution. In addition, some users will encounter ink backflow, abnormal ink supply and color loss caused by insufficient ink cartridge pressure.

Problem 3: It is inconvenient to carry and easy to spill ink.

Miss Wang works for a small book company. Every day, a large number of samples are typed out and sent to the publishing house for review. In order to control the printing cost to the maximum extent, a month ago, we began to use the modified continuous supply machine. One day, she found a lot of ink on the printed sample. After careful inspection, it turned out that there was ink leakage under the machine. In less than a month, the desk where the printer was placed has changed beyond recognition, and it is very troublesome to clean it up.

In fact, the root cause of Miss Wang's ink overflow lies in the modification of the connection mode between the ink box and the fuselage of the continuous ink supply machine. The modified continuous ink supply machining is rough and rough, and there is no effective setting to control the ink supply, which is very easy to cause ink leakage and backflow during handling, resulting in printer failure and ink leakage. In addition, the waste ink pad of the continuous ink supply system is easy to be filled.

Of course, because the ink conveying pipeline of the modified continuous ink supply machine is long and random, when the printer cleans the nozzle, it also greatly increases the generation of waste ink, which makes the waste ink pad easily occupied. Moreover, due to the unbalanced pressure of the continuous ink supply system, ink will leak from the print head to the waste ink pad, and the ink will accumulate and leak out and even flow to the desktop for a long time.

Question 4: Without after-sales service, service is not guaranteed.

BMW cars are equipped with tractor engines. Should the BMW tube or tractor factory repair the problem?

This joke accurately describes the psychological fear of users who modify the continuous supply machine, especially the fear of machine problems. Once there is a problem, the user will be sent to the manufacturer's repair station, and the manufacturer will push the user to the modified supplier in the way that the user no longer enjoys the warranty after modification and needs to find a third-party service. The manufacturers who modified the continuous supply pushed the users to the original manufacturers because of their limited technology. The reasons of both sides are also very sufficient, putting users in a fair and reasonable embarrassing situation.

This is the biggest dead hole of the modified continuous ammunition feeder. No after-sales, no guarantee. In order to reduce the cost of subsequent use, many users took the risk of equipment damage to DIY, and finally found that they didn't spend less money and gas. Therefore, it takes some luck and psychological endurance to modify the' users' of the continuous supply machine. Otherwise, maybe you will become one percent of the experiment.

Troubleshooting of mp288 ink cartridge of inkjet printer

I found the reason why we need a piece of paper to block it. In fact, it is to thicken its edge. The specific thickness is about 1 mm, which should be enough according to the actual situation!

Sometimes, due to too many times of adding ink, the label of the ink cartridge is too loose, and the ink cartridge cannot be recognized because of curling. At this time, just stick the curly part with transparent glue. However, it should be noted that the transparent adhesive force is greater than the original ink cartridge label sticker, which may lead to air hole blockage, stripe printing, and nozzle pattern inspection showing a pattern similar to nozzle blockage.

Also, be sure to pay attention to the original ink cartridge when filling ink, because the filter screen and nozzle are under the sponge directly below the air hole, and if the needle sticks to the end, it will directly damage the nozzle.

My basic point of view is that this kind of ink cartridge is a self-destructive ink cartridge, which burns itself constantly under certain trigger conditions, and finally burns until the nozzle can't spray ink. It seems to be a blockage, but it is actually self-immolation, which can't be cleared by boiling water or other methods. In the end, it was E5 fault, so it couldn't be used any more, so we had to throw it away. The key is this trigger condition. Some people say it's the number of on-off and on-off. Try to reduce the number of on-off times, or don't shut down, and you can't turn off the ink monitoring software. It is said that there is a trap. In this way, although the two lights flash together, they can still be used continuously. Based on my experience, I want to put forward another hypothesis. The tolerance of ink adding is not on the switch, but the number of times the platen is lifted when the power is turned on, that is, the number of times the electric ink box is removed. This operation will trigger a program to detect the number of times the ink box and writing ink box are removed, such as burning the ink box after the ink box is removed for 50 times.

It has been about half a year since mp288. * * * Changed two sets of ink cartridges. The first set was bought because the black and blue could not be washed clean. Yesterday, I found that the blue was blocked again, and repeated cleaning was ineffective. So I removed the ink cartridge, unplugged the elbow connected with the connecting pipe, sucked some clean water with a syringe, pressed it on the hole of the elbow, and filled the ink cartridge with water. Find a container to receive water below. When the ink cartridge is full of water, it will spray a thin water column from the nozzle, like a fountain. At this time, if you look closely, you can see where the water curtain is blocked and you can't spray it out. So I repeatedly suppressed it, but I didn't expect to get through! Put it on the printer and test it. Because the ink box is full of water, after connecting the pipe, I sucked it with an ink suction clip, and finally cleared the serious jam! But the ink just installed on the machine is a little pale (probably because there is clear water in the ink box), but it doesn't matter, just play for a while.

;