After the putty is approved, the owner directly accepts it with a flashlight. When the oil owner saw this, he was anxious at once.

In interior decoration, it is very important to approve putty, and many families will also find professional masters to construct it when approving putty. What I want to say today is that when the owner accepted putty indoors, the owner actually took a flashlight to accept it, which made the construction master anxious. It's embarrassing for the owner to accept this. Let's find out.

First, let's see what's going on.

As can be seen from the owner's house, the acceptance method adopted by the owner is to illuminate the wall with strong light. In this way, even if there is a little scratch and a little graininess on the wall, you can see it clearly. Of course, this is also a very standard way of acceptance, and many friends know it. But in fact, although this kind of acceptance method is good, there are few masters who can reach this technical standard. Or in other words, few oil workers are willing to do so. After all, it is handmade, so it can't be all right. Moreover, the master's fee is also available, but it is a very formal market price.

Therefore, when the oil owner saw the owner's acceptance, he immediately became anxious. Because the master knows what he is doing, there must be problems, but these problems are hard to find without looking carefully, and now the master can definitely find them by testing with strong light. Finally, the master said: If the inspection must be carried out according to this standard, there is no way to do this work. Although the wall work is over now, only latex paint spraying and post-repair have not been done. I hope the owners will not be too embarrassed.

Judging from the above situation, there is nothing wrong with the owner doing this, but sometimes it is necessary to consider the actual situation and imagine. Sand the wall with hand sandpaper. How can there be no scratches? If you must make sure there are no scratches, you must repair them slowly. Few experts are willing to do this. As for the acceptance of wall engineering, as long as the overall flatness and the vertical levelness of the angle of Yin and Yang can be guaranteed, there is no obvious problem. What do you think of this?

Second, what is the acceptance standard of putty?

1, check whether the surface of putty is dry. If the putty dries before painting, it will crack easily.

2. Check whether there are cracks on the surface of putty. Cracks must be handled in time.

3. Check whether the surface of putty is complete and smooth, and check whether there is a light side on the wall. There should be no obvious unevenness on the surface.

4, check the handover between metope, metope and top surface is straight.

5, check whether there is a boundary between metope and wood products is not clear. If you scrape putty on wood products, it will affect the external light of wood products and must be removed in time. Top putty can also be accepted by the above method.

6, check the window sill, door frame and other small parts, should be smooth without scraping. Note: After the putty is approved, the surface is polished with fine sandpaper to achieve the reflective effect, which feels like a metallic reflective effect. Don't worry about paint dropping or sticking, only in this way can the paint layer be smooth and shiny.

3. What is the construction process of wall putty scraping?

1, primary treatment

Due to the floor, materials and other reasons, the smoothness of the wall surface of cast-in-place concrete is slightly poor, and there will be pores and pits. Therefore, it is necessary to repair the unevenness of the wall. For defective parts such as honeycomb, the gypsum putty shall be filled and compacted with a steel scraper, leveled and leveled. Then use a special wire brush to clean the surface impurities, keep the wall flat and dry, and then proceed to the next process.

2. Apply adhesive (fruit juice)

Do a good job on the wall before scraping putty, and mix glue and water according to a certain proportion before spraying. Spraying must be uniform, without omission. Then you can scrape putty. When scraping, pay attention to scraping back and forth, pay attention to scraping seams up and down, left and right, and no floating putty can appear.

3. Repair and polishing

After scraping the putty for the first time, you can re-check the place where it was repaired before to see if there is any problem. If there is still collapse, it is recommended to repair and level it again, dry it and then polish it with sandpaper, and then clean it.

4, putty survival

After the first putty dries thoroughly, you can directly brush the putty for the second time. Generally, scraping putty twice is enough, and the surface texture is required to be flat and consistent. There shall be no phenomenon of different shades of color, which will seriously affect the decorative effect in the later period.

For indoor construction, foundation decoration is a very basic construction step. When decorating, we should find a professional and regular construction team to carry out the construction. Attention should be paid not only to the construction steps, but also to the construction skills, to ensure that the interior looks smoother and more beautiful, and to improve the overall indoor decoration effect.