Tips on wall painting standards and follow-up inspection

Painting the wall is a project that must be implemented in the decoration process, and the quality of painting the wall is directly related to the living environment of the residents. In order to build a comfortable house, the requirements for wall brushes are strict, the wall powder and wall brushes are fine in workmanship, and the standard quality inspection of painted walls is very strict, thus ensuring that the walls are beautiful, durable, healthy, harmless, comfortable and livable. Let's take a look at the standards of wall painting and the tips for follow-up inspection.

Standard 1 for painting walls:

Check the walls. Is the distance from the wall 1.5? M away, confirm with the naked eye whether the paint on the wall is saturated and clean. If you want to see the situation better, you can take a flashlight along the wall to confirm whether the wall is uniform and the color is consistent. The wall surface should be painted evenly, firmly bonded, without leakage, endless surface and corrosion. At the same time, a comprehensive inspection of wall coatings is also necessary. The coating effect of low-quality wall coatings is greatly reduced.

Mural standard 2:

Thoroughly check the surface quality of wall paint. The wall is smooth, symmetrical, delicate and uniform, and the touch is suitable for the human body's sense of beauty. Secondly, the wall color of every other room must be consistent, and the wall should be even and smooth. In general, the basic treatment after wall painting is small nitrolacquer 8? ~ 12 times, if polyester paint is not applied for 3-6 times, the number of brushing will be reduced during the construction process, which will affect the decorative effect. This is one of the important standards for painting walls.

Standard 3 for painting walls:

When you brush, you should know the standard of wall painting, accept dry paint completely, and check it by hand or visually. The paint on the wall is smooth and delicate, and there are no obvious traces of painting. It is required that the color of the brush is roughly the same as that of the wall, and the brush is not allowed to shed hair, peel, mottle or fall off.

Standard 4 for painting walls:

Paint mixing should be carried out after the paint is completely dry, but on-site inspection can be carried out through vision and touch. Manufacturing accuracy 1m? M steel plate can be measured, and the bidirectional electrical assembly line within 5m can be measured with the main inspection benchmark. The standard of painting the wall requires that the wall surface should be flat and smooth, and there is no obvious pass, so it should be removed or the rust prevention phenomenon should be ended.

Point 1. Inspection of substrate structure:

Wall engineering can often run through the whole process of decoration. If there are walls or shapes, you can enter the early stage of construction. If it's just paint powder, work from the middle and second half. However, for the construction of wall topcoat, the paint must pass through the nozzle, putty, polishing and topcoat, especially in road engineering. If the engineering specifications are not strict and the wall paint is not enough, it may not be possible to wait together with before.

Second, material inspection:

Wall powder involves the whole room, so the quality of paint affects the whole family environment and human health. For example, when choosing paint, it is not poor quality, but indoor decoration problems such as spots are prone to occur. Water for bed paint should be used with moderate concentration and should not be used too lightly.

Third, the painting process inspection:

The inspection of brush technology is also related to the quality of wall painting. For example, shave at least three times when you are tired. Moreover, boredom cannot be too strong again and again. Wait until it's completely dry every time. If you start to apply opaque milk paint, the wall will break easily. When you are tired, use sandpaper to smooth all the walls. If the wall is desired, the latex paint exposing the brush is shallow and unsightly. Primer, large brush, corner brush, at least 3 times, each time after drying.

The above are the main points of wall painting standards and wall engineering inspection.

Tubatu Online provides you with "every decoration quotation, 1-4 local decoration companies, 3 sets of decoration design schemes" and the decoration pit avoidance strategy for free! Click this link:/Zhu Ye /zxbj-cszy.php? to8to _ from = SEO _ zhidao _ m _ jiare & amp； Wb, you can get it for free ~