Tutorial on car film wrapping methods and steps and precautions for car film wrapping

Solar film installation tips Car solar film, commonly known as explosion-proof film, refers to a film that is pasted on the surface of automobile glass. It not only has the function of explosion-proof, but also can insulate and block light. High-quality explosion-proof membranes are usually made of a special polyester film as the base material. The membrane itself is tough and equipped with special pressure-sensitive adhesive. In the event of an accident, even if the glass breaks, it can be disconnected without hurting anyone. Today's car explosion-proof film also has one-way perspective and glare reduction functions. Introduction to the steps of car film wrapping: 1) First spray clean water on the inside of the clean glass, then tear off the protective film of the solar film, spray clean water on the coating surface, and then select a film of appropriate size. 2) Attach the solar film to the glass and cut along the edge. 3) After pasting, there will be many bubbles on the glass. 4) Squeeze with a plastic spatula. 5) Baking paint is finalized. 6) Do some detail processing. 7) Finally rinse the car body. Tip: After applying the film, you can put a reminder sticker in a prominent position to warn the car owner not to roll down the window for three days. Since the solar film is affixed to the inside of the car window, clean water should be sprayed into the car before applying the film to allow dust particles to sink as quickly as possible. When applying the film, although the temperature inside the car is high, do not use the air conditioner in the car. Precautions in car wrapping to avoid sand in the wrapping: (1) Many construction workers will use tap water directly when working, but there are many impurities or sand in the tap water pipes, which should be avoided without filtration or sedimentation. (2) Dust Many stores do not have a dedicated film room. Cars whizzing by will stir up a lot of dust, and sometimes there will be dust when the wind speed is high. Therefore, when there is no laminating room, all doors should be closed before laminating. (3) Work clothes When the transparent part of the insulation film is disassembled, a large amount of static electricity will be generated. Therefore, avoid wearing woolen or cotton-filled clothes when applying stickers, because static electricity will attract the cotton or wool on the clothes to the film. (4) Films whose surface has been cut are usually placed on car floor mats, seat covers, or on car roofs and engine hoods, making the internal and external environment unclean. At the same time, dust attached to its surface will also be sucked to the membrane when it is removed due to static electricity. Therefore, the transparent film must be cleaned or sprayed with water before it can be disassembled to prevent dust and sand. (5) Chair covers or decorations. Some chair covers or upholstery are made of rabbit fur, fox fur, or cotton. Due to static electricity, be careful when removing the film. And when removing the film, avoid being too close to the object to prevent dust on the object from being sucked away by static electricity. (6) When someone opens the door, opens the film or washes the glass, try to be careful not to let anyone outside the car open the door. Forcing the door open may cause outside air to enter quickly and bring in large amounts of dust or sand. (7) The wind speed of the air conditioner is too high, and it is relatively hot in summer, which is the peak season for applying insulation film. Due to the high temperature in the sun or in the car, it is inevitable that the air-conditioning film is turned on in the car. But when turning on the film, the air conditioner fan speed should be adjusted to the minimum. After peeling off the film and sticking it to the glass, increase the wind speed. (8) The bottom of the sprinkler is not clean. When in use, sprinklers are generally placed on the ground, on foot mats or chair covers, and the bottom is generally not clean. When you take the membrane apart, if the nozzle is rocking back and forth on top of the membrane, the bottom is there. Sand and pebbles will settle on the membrane, so wipe the bottom of the spray head before use. (9) After removing the transparent film by hand, you must use two fingers to pinch the insulation film. Fingerprints and sand will appear on the pinched part. The difficulty is to control the film with as little pinching as possible. (10) The wiping method is incorrect. When wiping the glass, the wiper cannot be wiped casually, or the wiper may be intermittent, or the result may be unclear. There is a fixed way of wiping, otherwise it will bring sand. (11) When the flushing wiper cannot reach (12) The next step after the film is attached to the wiping direction is wiping. Water can be scraped from top to bottom, left to right or right to left. However, in order to prevent water from flowing downward and causing sand particles to fall down, a large amount of water cannot be scraped from bottom to top.