How to modify the access control password?

How to modify the password of glass door access control? There is no 5 in the manual.

(Any setting of the controller must be made in the programming state. )

(1). Enter the programming mode:

Press [*]+[6-digit programming password] and beep twice, (the red light flashes and the green light is always on. The factory programming password is 990 10 1. The user must modify the programming password after enabling the access control equipment. If there is no programming instruction within 20 seconds, the system will automatically exit the programming state. )

(2). Modify the programming password:

Press [0]+[6-digit new programming password]+[Repeat 6-digit new programming password] and beep twice; Indicates that the setting was successful.

Give it a try! If not, find the manufacturer who installed the access control for you before! !

How to modify the password of this entrance guard? 5 points

1. First, you must know the programming password. The default programming password should be 12345.

2. Modify the password to open the door:

1) enters the programming state:

Press * to enter the administrative password, then #.

2) Press 5 to enter the new four-digit password, press #, then enter the new four-digit password again, press #, and then press * to save.

Note: The password is an arbitrary four-digit number.

How to change the access control password

Hello, I'm glad to answer your question:

Password access control machine setting modification method 1

1. Initial password: the programming password is 9999, and the use password is 1234.

2. Enter the programming state: function setting (in the programming state). Door state monitoring needs to cooperate with door magnetic switch. When this function is turned on, it has the following two functions: first, if you forget to close the door after entering the correct password, the buzzer will beep to remind the user to close the door; Second, if the door is illegally opened, it will start the alarm signal output and the buzzer will give a warning. The factory sets this function to off.

3. Usage: Under normal working conditions, you can open the door by reading a valid card; If you need to read the card and add a password, you can enter the correct password to open the door within 10 second after reading the card; If the user forgets the password of the card, he needs to delete the card, add the card again and modify the password himself. If you forget the programming password, you can use the jumper switch "reset" on the motherboard to restore the factory settings. Before turning on the power supply, turn off the power supply and turn the jumper switch to the "ON" position. After the buzzer rings for three times, turn the jumper switch back to the "OFF" position to restore the factory settings. Please turn off the power supply before installing the wiring, and do not operate with electricity! Under normal circumstances, the electric lock is connected from the power controller.

Password access control machine setting modification method 2

1. Enter the programming mode: press [*]+[6-digit programming password] and beep twice, (the red light flashes and the green light is always on. The factory programming password is 990 10 1. The user must modify the programming password after enabling the access control equipment. If there is no programming instruction within 20 seconds, the system will automatically exit the programming state. )

2. Modify the programming password: press [0]+[6-digit new programming password]+[Repeat 6-digit new programming password] and beep twice; Indicates that the setting was successful.

3. Set the door opening mode: card or general password: press [1]+[0] and beep twice; Card plus personal password: press [1]+[1] and beep twice;

4. Set the door opening time: press [2]+[TT] and press it twice; TT indicates the opening time in seconds, and TT = 03； if the unlocking time is 3 seconds;

5. Set/modify the universal door opening password: press [3]+[4-digit new universal door opening password] and buzz twice, and the original 4-digit universal door opening password will be overwritten; Press [3]+[0000] and beep twice to clear all "common passwords";

6. Forced recovery of the factory programming password: remove the controller, short-circuit J2' s two feet, and then release it (power-on). The controller will make a beep first, then make two beeps, and the controller can restore the factory programming password.

I hope my answer is helpful to you. . .

How to modify the access control password

Press #, enter the system password 12345 or 123456, press 1 after entering, then enter 5 digits to modify the system password, and press 60+# to enter 8 digits card number+# to delete the single card.

How to modify the password of access control integrated machine

Every company's all-in-one settings are different. It's too easy for you. It is almost like a fairy. It is easy to change the model after reporting.

How to change the password in the access control system?

Different access control systems have different ways to modify passwords. I have 1 machine here. Press * 123456# to enter, and press 5 to modify the door opening password. You try

How to modify this electronic access control password? 100 point integral

CR-3 105A access control integrated machine working power supply: DC+ 12V static current: 50mA ambient temperature; -10℃-55℃ relative humIDity: 20%-90% RH identification frequency: id type 125 khz(EM or compatible card). IC type 13.56 MHz(MF 1 or compatible card) door opening mode: card or universal password programming mode: key valid card: 1000, Appearance dimensions: 15 mm * 76 mm * 22 mm general password: 1 card reading distance: id type 5- 12 cm IC type 3-8 cm signal output: relay output/level output button interface: 65433 WIEGAND26 format valid card personal password: 0000 unlock detection door magnetic state:. Key +252005 (default programming password): Enter the programming mode 1+ 1: Card plus password opening mode 1: Card or password opening mode 2: Set the locking time 3: Modify the general password (key 5678 opens the door) 4+0: Turn off the tamper alarm 4+/kloc-0. 7+3-digit digital code /7+ induction card: delete valid card 6+0: effective instruction for unlocking (detecting door magnetic state when unlocking) 6+ 1: effective instruction+door magnetic closing (multi-door interlocking or anti-stalking) 8+0: door magnetic alarm function 8+ 1: door magnetic alarm function 82+TT (.

How to modify the community access control password?

Press #, enter the system password 12345 or 123456, press 1 after input, and then enter 5 digits to modify the system password.

Press 60+# to enter an 8-digit card number+# to delete a single card.

If this method doesn't work, please ask the property for help.

How to change the password after the password of access control programming is changed?

88 10C inductive Carmen controller

operation instruction

I. Product introduction:

This kind of induction card access controller is specially designed for various electronic door locks and security systems. It is one of the most advanced access control systems in modern times. It uses the latest central processing unit (CPU) and large-capacity storage chip, and all data will not be lost due to power failure; With the latest technology and powerful functions, there are three ways to open the door: induction card, induction card plus password and pure password.

Perfect safety measures such as door state monitoring, output alarm, anti-disassembly, induction card and password combination make users safer; Powerful functions such as door opening button, doorbell, normally open or normally closed can make users more convenient.

This product provides a safe and automatic access control mode, and is an ideal device for commercial institutions, offices, factories, houses, communities and other places.

Second, the technical parameters:

Serial number item index

1 working power DC: voltage 12V 10% current "0. 1A"

2 Maximum load alarm output: 100mA Electric lock output: 5A

3 External dimensions116mm×116mm× 20mm.

4 weight180g

5 Ambient temperature -20℃-60℃

6 Relative humidity 20%-90%

7 Storage capacity: 500 user cards and 500 passwords.

8 reading distance 5- 15cm

9 reader type EM or EM compatible card

Three, sound and light instructions:

LED indicator:

Events are red and green.

The normal state flashes once every second.

Read the valid card and flash it twice continuously.

Reading illegal card lights

Unlock and light.

The typing key lights up.

Enter the programming light and flash quickly.

The programming confirmation light is on.

Warning flashing

Built-in buzzer:

The incident is clear and sounds clear.

Double-click to read the valid card.

Illegal cards that have been read for a long time-

The key is valid within a short beep.

Enter a password that is valid after two short clicks.

Incorrect password input, a long sound-

The alarm status keeps ringing-beep-beep-

Fourth, set the usage method:

1, initial password: the programming password is 88 10, and the use password is 0000.

2. Password modification (non-programming state): Press * to read the user card, and the green light flashes. Press the password, and then press # to enter the password modification program. Enter a new four-digit password, then press # and then press # to save.

3, enter the programming state:

Press * Programming Password # to enter the programming state.

4. Function setting (in programming state):

（ 1）

Press 0 New Password # Repeat New Password #

Note: The password is any of 4-8 digits.

② Add user card:

Press 1 to read the card and enter the card code #

Note: The code of the card is 00 1-500, which is a non-repeatable three-digit number. You must enter the code, otherwise the card will be invalid.

If you need to add continuously, you don't have to press # to read the second card directly after entering the three-digit code.

(3) Delete the user card (there are three methods):

A, press 2 0 0 0 # to delete all user cards;

B, press 2 card reading # to delete the card reading;

C, press the card code # of 2 to delete the lost card;

④ Set the door opening mode:

Press 3 0 0 # to read the valid card to open the door.

Press 3 0 1 # to read a valid card and enter the correct password to open the door.

Press 3 0 2 # to read the valid card or enter the correct password to open the door.

Note: the factory setting is to open the door immediately after reading the valid card;

If you set a password to open the door, you must change the password, and the initial password cannot be opened directly.

⑤ Set the opening hours:

Press 4 X X #

Note: XX is 0 ... ";

How to modify the general password of mg236b access control?

Change the programming password:

[0]

+[6-digit new programming password]

+【 Repeat 6-digit new programming password 】