Samsung CDMA test description test mode

A, *759#8 13580 and then enter the test mode, all commands can press # to end the command:

Command display interpretation

0 1 Pause: Some commands need to be executed first.

02 Exit the test and enter the test state, and the power off key does not work.

07 carrier on transmission carrier on

08 carrier off transmit carrier off

09 chan-0283 initial channel 2 1#0000 The mobile phone is locked and the network cannot be connected.

22 send nam displays the programming content and turns pages with *.

23 Send ver display version, and use * to turn pages.

24 send esn display electronic serial number, eight hexadecimal, use * to turn pages.

25 Backlight on Backlight on

26 Backlight Off Backlight Off

27 indicator light is on.

28 light off indicator light off

30 product information to generate mobile phone information

The vibrator began to vibrate.

49 vibrator off vibration off

50 bytes =2 18(7) battery capacity data (factory setting)

52 h/w=47f.04 Version number

53 Lock Code: 0000 Displays the lock code.

57 mic on unmute microphone

58 mic mute microphone off

59 sio mode 1 serial output mode, when it is 1, it can communicate with the microcomputer through the bottom connector.

Section 67 vai reading battery parameters

68 stby batt-XXX battery data sampling, varying with voltage.

69 talk batt-XXX battery data sampling changes with voltage, which is used as a reference for 70 commands.

70 WR Bat T-XXX reads and writes electrical data 000-255, which are stored in STO and adjusted in case of low voltage alarm.

7 1 cd txagc-XXX transmission power level xxx=000-5 1 1, stored in STO. The larger the value, the larger the transmitting battery. Do not transmit current for a long time.

72 cd txagc-XXX accepts the gain xxx=000-255 and stores it with STO.

74 Tx RAS[xx]xxx transmission power level [01-16] XXX = 000-555, and the first line shows the corresponding decibel value.

75 rd rssi shows the field strength value, about 50 is normal.

76 wd rssi field strength stored value

The 77th temperature reading battery temperature.

79 buzzer sounded

80 buzzer off the bell

8 1 pcm loop turns on pcm codec loop.

82 pcm loop off pcm codec cycle off

85 sperker on receiver on

86 speaker off receiver off

2. Press M-6-* in the standby screen to enter the system program with the password of 000000.

3. Press M-9-0 in the standby screen to enter the user lock. If it is not set, the initial user lock is 0000, and you can enter the Internet settings.

4. Press M-8-* in the standby screen to enter the test screen. The password is 1235806.

A300 instruction

-Samsung A300 manual-

*#9998*4357# List of available descriptions (that is, help, you can see most of the following descriptions);

*#9999# View the software version;

*#0837# shows the hardware version (including the software version and the hardware production date, and the sixth screen MP V 1.xxx is the hardware version);

*#000 1# displays RS232 serial communication parameter settings;

*#0324# Network detection (engineering mode);

*#0636# Memory capacity display;

*#0842# Test vibration;

*#0289# or *#9998*289# test ringtone (ringtone adjustment, ringtone frequency test/display frequency, up and down key adjustment);

*#0228# or *#9998*228# or *# 1999# displays all information of the battery, battery parameters, battery capacity, type/voltage/temperature;

*#0778# or *#9998*0778# Flip the screen to display the details of the SIM card;

*#0782# RTC display (seems to display the current clock)

*#0523# or *#9998*523# LCD contrast, use the up and down keys to adjust.

*#9998*364# shows watchdog status.

*#9998*427# Watchdog signal path setting

*#9998*746# SIM card file specification test

*#9998*0377# Software error log (EEPROM error display)

*#0638# SIM network ID

*#9998*3323# Forced collapse

(This column is estimated to be used for program debugging. Use it with caution. Some crashes can only be discharged. )

*#9998*9266# shows the receiving channel number and receiving intensity;

*#9998*786# shows the time of this startup and the time since startup.

Press-to display the latest time from this boot to now;

Press again-displays the last startup time;

Press again-displays the last shutdown time and the last shutdown time;

*#9998*5646# Change the boot display country (GSM logo set);

*2767*3855# or *9998*947# Restore the IMEI code in the mobile phone Flash to the EEPROM chip.

Re-use *#06# to check whether the IMEI has been changed;

*2767*927# This is the solution to WAP setting and surfing the Internet in Version I5;

*2767*2878# machine main reset! The phone book and phone settings in the phone will be deleted;

*#9998*76# or *#9998*0076# It will be on your mobile phone.

"Production number" prompt,

If your Samsung mobile phone is licensed, there is a string of numbers under "Numbers".

There is no parallel import;

S508 Complete Test Instructions

S500 Some commands have functions that previous models didn't have, and they are very functional. Hey?

In particular, there are two unlock instructions, no matter what lock the phone has opened.

Mobile phone lock, SIM card lock, network lock, user lock. ......

You don't need a data cable, you can immediately "cancel all" and keep the phone book as long as you enter an instruction!

*#06# shows the IMEI code of international mobile equipment identification.

#* 1200# AFC DAC value

#* 1300# IMEI

#* 1400# IMSI

#*5 1 1 1# status

#*2565# (BLOK) Unblock General Defense

#*3353# (Deco) General defense code was deleted.

# * 7222 # (SCAC)-Class C GSM

# * 7252 # (SCLB) Class B GPRS

#*727 1# (SCS 1) multi-slot class 1 GPRS

# * 7274 # (SCS 4) Class 4 multi-slot GPRS

#*2787# CRTP on/off compulsory detection of battery temperature on/off.

#*3737# status, AFC value

#*5 132# (L 1DA) status

#*5 133# (L 1DE) status

# * 7288 # (satt) GPRS connection/disconnection GPRS connection/release.

# * 7287 # (sats) GPRS att/det status GPRS promotional materials @

#*7666# (RNMO) status

#*7284# (SBTG) Set Class B to GPRS.

#*2256# (BALO) Kalibu. -Information

#*2286# (BATA) data battery data

#*7352# BVMC set 0h debugging battery

#*2558# Time to debug the battery

#*2474# cmd set debugging battery

#*2527# GPRS switch 4, 8, 9, 10

#*2679# Copy function on/off

#*3940# External loop test 9600bps

#*394 1# external loop test 1 15200bps

# * 4263 # (Manual) Hands-free mode on/off Hands-free function on/off.

#*4700# (HR00) Half-rate On/Off is turned on by default.

It is recommended to turn it on to increase the continuous talk time of the mobile phone.

# * 3370 # (efr0) eft On/Off Enhanced Full Rate On/Off

It is turned on by default. It is recommended to turn it on to improve the call quality.

#*7462# (SIMA) SIM card function type in SIM stage

#*7983# Voltage/Frequency On/Off

#*7986# Voltage On/Off

#*7693# (SMXD) Sleep Act/Deact power saving mode switch

#*8462# Sleep state power saving mode state

#*7683# (SMVE) Sleep variables

# * 5176 # (l1pn) l1sleep state

#*7632# (SMDB) Debugging of sleep mode cancels power saving mode.

#*7673# (SMRE) Sleep Mode Reset Power Saving Mode Reset

#*8466# Old time-sleep, SMReq, wake up

#*2255# Call Failure Mode ...

# * 5187 # (l1tr) l1c2g tracking

#*5376# Restart?

#*6837# Official software version Official software version?

#*7524# KCGPRS

#*7562# LOCI GPRS

#*7638# RLC On/Off

#*2337# Permanent registration beep

#*2834# Audio PathOpen the audio path.

#*3270# (DCS0) DCS supports on/off support 1800M on/off.

#*3282# Data On/Off

#*3476# EGSM On/Off

#*3676# All phone books need to be deleted after the flash volume is formatted and used.

# * No.4674 IMSI

#*4760# GSM, activated/deactivated

# * 5171# (l1p1) status

#*5 172# L 1P2

#*5 173# L 1P3

#*7326# Accessories: vibrator

#*7762# (SSMB) SMS carries CS, activated/deactivated.

#*8465# (TINL) time is in L 1

#*9795# Wtls key reset

#*2252# (CALC) Current calibration

#*2836# AVDDSS management on/off

#*3877# Dump Spy Tracking

#*2677# (AMRS) AMR status: none/half price/full price.

*#2255# (Call Record) displays the call record.

*#8999*324# (DAG) Netmon network reception status

*#8999*377# (ERR) Error Log Mobile phone error record

*#8999*636# (MEM) Memory Status Mobile phone memory status

*#8999*8378# (test) test mode test mode

Display version (hardware version, software version, IMEI), hardware test (vibration test, audio setting (speaker gain,

Microphone gain, music gain, speaker volume (normal, mobile phone, hands-free, earphone), key tone (normal, mobile phone,

Hands-free, headset), tone calibration gain, speaker volume (headset), battery information), lock status, SIM card information (SST, CPHS, phone book, exit, SMS, language, IMSI) and product information.

* # 4777 * 8665 #(GPRS * tool) GPRS settings

* # 8999 * 523 # (LCD) Brightness adjustment of main screen in main LCD brightness.

* # 8999 * 3825523 # (eTallcd) Photometric adjustment of external lcd screen

*#9999# Firmware Version Software Version

*#8999*8376263# Firmware Details describes all software versions in detail.

*#8888# H/W version shows the hardware version.

* # 8377466 #(VERSHNO)S/W & amp； Hardware version

#*6420# (Microphone 0) Microphone off

#*642 1# (MIC 1) The microphone is on.

#*6422# (MICA) The microphone pair receives data.

#*6428# (MICT) Microphone Measurement

#*3230# Tracking, enabled

#*323 1# DCD, enabled

# * 3232 # Display DCD/ Tracking Mode DCD/ Tracking Status

#7263867# Memory Dump On/Off

*#7465625# All locked states Mobile phone locked states

* * * The following instructions are not recommended, otherwise you need to unlock the phone!

* 7465625 * 638 # (SIMLOK * NET) network lock is enabled to open the network lock.

# 7465625 * 638 * # Disable network lock with password and close network lock.

*7465625*782# (SIMLOCK*SUB) Subnet Locking Enabled

#7465625*782*# Unlock subnet

*7465625*77# (SIMLOCK*SP) Open the SP lock.

#7465625*77#

*7465625*27# (SIMLOCK*CP) Open the CP lock.

#7465625*27*#

*7465625*746# (SIMLOCK*SIM) Open the SIM card lock.

#7465625*746*#

*7465625*228*# (SIMLOCK*ACT)

#7465625*228*#

*7465625*28638# (SIMLOCK*ATNET) Network lock automatically opens.