How to open the OP bathroom heater?

Question 1: How to remove the Opp bathroom heater and wash it? If it is an integrated bathroom heater, pick a corner of the bathroom heater's mask and pull it off. If it is a non-integrated bathroom heater, just find the circlip or hidden screw location.

Question 2: There are lights, ventilation, blower, heater 1 and heater 2 on the Opp bathroom heater panel. How to use it. Don’t know how to turn on the order? Not to mention the lights, turn on the blower first, and then turn on the heater 1 and heater 2 according to the indoor temperature. After use, first turn off the heater 1 and heater 2. Leave the blower on and let the blower cool down the heat pipe (after 3-5 minutes). Then turn off the blower and turn on the ventilation to blow out the moisture in the room.

Question 3: How to use Opp’s bathroom heater? Needless to say, lighting and ventilation

Air heating 1 and air heating 2 are PTC heating wires, such as 1500W divided into 2 levels, one button and one level 750W.

Before turning on the fan heating, you need to turn on the blow button, so that the wind can blow down and you can get real fan heating. Otherwise, the PTC heating block will only heat up and not blow down.

It will burn out. (Of course the wiring is correct. If you don’t press the hair dryer button, the air heater button will not have electricity)

Question 4: How to install the Opp bathroom heater purchased online? How to install the bathroom heater

Confirm the installation of the bathroom heater After installation, the height of the lowest bulb of the bathroom heater from the ground should be between 2.1 meters and 2.3 meters. In order to achieve the best heating effect, the bathroom heater should be installed on the suspended ceiling directly above the center of the bathtub or shower room. For suspended ceilings, please use materials with better strength and less noise. If the ceiling is too high or too low, the effect will be affected. (Warm reminder: Generally, when using the bathroom heater, keep your back close to the bathroom heater. Do not point your head directly at the bathroom heater, which will affect your health.)

Install a ventilation window. Put one end of the ventilation pipe on the ventilation window, and the other end of the ventilation pipe. One end is fixed from the outside of the wall along the ventilation window at the air outlet of the exterior wall, and the gap between the ventilation pipe and the ventilation hole is filled with cement.

Children’s shoes with air outlets and ventilation fans at home should not need to do this step. The air outlets should be opened in front of the ceiling. Installing a ventilation fan requires an air outlet to suck out the indoor air, even on cold days. Need some fresh air. Children's shoes without a suspended ceiling can refer to the requirements and methods for reserved installation openings according to different gusset plates. The following air outlet sizes are listed. The standard aluminum gusset plate ceiling bathroom heater opening size is 300mm*300mm or 300mm*600mm (you can leave a piece of 300* The position of the gusset plate of 300 is not installed). The size of the bathroom heater installation opening should be reserved before suspending the ceiling. For waterproof gypsum board ceilings and sauna board ceilings, because you need to confirm the position of the keel, please also determine the size of the opening for installing the bathroom heater when installing the buckle board.

Reserve wires. Bathroom heaters are generally divided into lamp-heated bathroom heaters and air-heated bathroom heaters. Different bathroom heaters have different standards for leaving wires. For example: air-heated bathroom heaters: five sets of wires are reserved, including one for lighting. , a set of internal circulation hair dryers, a set of PTC heating sheets, a set of negative ions, and a set of ventilation. Light heating type bathroom heater: four sets of wires are reserved, one for lighting, two for lighting and one for heating, and one for ventilation.

Fix the bathroom heater and remove the mask, unscrew all the light bulbs, detach the spring from the ring of the mask and remove the mask and then connect the wires. Connect one end of the interconnecting soft wire to the switch panel, and the other end to the switch panel. Pull the power cord together from the ceiling opening, open the terminal cover on the box, connect the wires as shown in the wiring diagram and terminal marks, cover the terminal cover, and fix the terminal cover with screws. Then stuff the excess wires into the ceiling so that the box can be stuffed into the hole smoothly.

To install the bathroom heater, first connect the ventilation pipe, pull out the end of the ventilation pipe that goes into the room and put it on the air outlet of the centrifugal fan cover, then push the box into the hole, and select according to the position of the air outlet. Insert the bathroom heater box into the hole in the correct direction; then use four wood screws with a diameter of 4 mm and a length of 20 mm to fix the box to the wooden rails of the ceiling.

Question 5: Does the wire that comes with the OP bathroom heater control switch need to be replaced? If replaced, how to open this control panel? What about prying open the shell? Urgent need, thank you, this is an open box, open the protective cover, use a small flat screwdriver to pry up the notch on the right, remove the fixing screws and take it out.

Question 6: How to remove the Opp bathroom heater lamp? The lamp cover is a plastic part with a buckle. Use a pen or screwdriver to pry it off.

Question 7 : Why is the three-on switch of Opp bathroom heater connected to four wires correct? There are four wires in one and three out

Question 8: Why does Opp bathroom heater turn on the heating lamp and exhaust fan when it is turned on? It may be the wires in your home. There are fewer pre-embedded ones, and one switch controls two sets of circuits

Question 9: The Opp bathroom heater and air heater cannot be used with the 5-point power supply. Blow warm air. This air heating button is controlled by the blowing button. Only when the blowing is turned on will the warm air PTC be heated and warm air can be blown out. Otherwise, it is easy to burn out. If you press the blowing/ventilating button, the warm air heating will be cut off, so there is no Warm air.

Question 10: How to solve the wiring diagram of Opp bathroom heater switch 4-on? I don’t know what kind of bathroom heater switch you use. Generally, the switch under the bathroom heater has five wires, which are two for heating, one for lighting, and one for lighting. exhaust. The remaining one is the common line connected to the neutral line, and the neutral line and the power supply neutral line are connected in parallel. The four-position switch live wires are connected in parallel with the four small switch modules, and then the two control lines for heating, lighting, and exhaust are connected to the corresponding wiring holes.