What should be done to ensure safety when working with a forklift?

When operating a forklift, how should it be operated to ensure safety?

When operating a forklift, strictly follow the forklift operating instructions.

1. Do not use the forklift beyond the rated load capacity

2. Before using or charging the electric forklift, you need to check the battery fluid and replenish it with distilled water if it is insufficient.

3. When charging the electric forklift, keep the surrounding environment dry, well ventilated, and away from flames.

4. When the forklift is not in use, the goods on the forklift should be unloaded and the forklift forks should be lowered to the lowest position.

5. The weight of the cargo should be distributed as evenly as possible on the two forks. It is strictly prohibited to bear force on a single fork or have the center of gravity of the cargo outside the two forks.

6. When the forklift is lifting or transporting goods, it is strictly prohibited to allow people to stand under the forks. Non-operators should stay at least 600mm away from the vehicle body. How to ensure safety when meeting a car on a curve?

When meeting vehicles on a curve, the center line of the road should be used as the boundary. If there is no center line, the geometric center line of the target should be used as the boundary. A lateral distance of one should be maintained. Both vehicles should be close to the right side of the road at low speeds. travel. Forklift operator's license, forklift operator's license application guide, how to apply for a forklift in Shenzhen

The forklift driver's license is a special vehicle driver's license. You must apply for it at the forklift training base designated by the national municipal quality supervision bureau. When applying, You must bring the original and copy of your ID card, and two one-inch photos.

Application conditions

According to Article 10 of the "Measures for the Supervision and Management of Special Equipment Operators" (AQSIQ Order No. 70): Persons applying for the "Special Equipment Operator Certificate" Applicants should meet the following conditions:

1. Aged 18 years or above;

2. Be in good health and meet the special physical requirements for the type of job you are applying for;

3. Have an educational level suitable for the type of job applied for;

4. Have work experience suitable for the type of job applied for,

5. Have corresponding safety technical knowledge and skills ;(If not, training is required first)

6. Comply with other requirements stipulated in safety technical specifications. Forklift operation safety training, what are the safety precautions for forklift operation

1. When starting

1

Before starting, observe the surroundings to confirm that there are no obstacles that impede driving safety. ,

Sound the whistle first and then start.

2

When the forklift starts loading goods, the driver should first

confirm that the goods being carried are stable and reliable

.

3

. The start must be slow and steady.

2.

When driving

1

The height of the lower end of the fork from the ground should be maintained

300-400mm

, the mast must be tilted backward

.

2

Do not raise the fork too high when driving. When entering or leaving the work site or while driving, pay attention to whether there will be obstacles in the sky.

The forks are not allowed to rise too high when traveling with goods, as this will affect the stability of the forklift.

3

After unloading, lower the fork to the normal driving position before driving.

4

When turning, if there are pedestrians or vehicles nearby, a driving signal should be given first. High-speed sharp turns are prohibited.

High-speed sharp turns may cause the vehicle to lose lateral stability and tip over.

5

It is strictly forbidden to turn off the engine and coast when the forklift is going downhill. It is forbidden to brake suddenly while driving without special circumstances.

6

When the forklift is operating, it must abide by the traffic rules in the factory and must maintain a certain safe

distance from the vehicle in front.

7

When the forklift is running, the load must be at the lowest position that does not hinder the movement, and the mast must be tilted back appropriately.

Loads must not be raised except when stacking or loading.

8

The height of the load must not block the driver's sight. In special circumstances, when objects affect forward vision, drive at a low speed when reversing

9

It is prohibited to turn on a slope or cross a slope. travel.

10

, safe driving speed in forklift factory area

5

kilometers

/

< p> When entering the production workshop area, you must drive at a low speed and safely

.

11

,

When the forklift is lifting, lowering or driving,

it is prohibited for people to stand on the forks to hold items and lift items. Balancing effect.

12.

If problems are discovered, repair and report them in a timely manner, and never work while sick or conceal any problems.

3. Leaving the forklift

1

It is forbidden to unload the goods or lower the fork frame before leaving the forklift when the items on the forks are suspended.

2

. The parking brake handle is pulled or the handbrake switch is depressed.

3

. The engine stalls and the power fails.

(Except for special circumstances, such as the driver not leaving the vehicle's sight and not exceeding

1

minutes)

.

4

, Remove the key.

4. Driving parameters

1

, must be checked before driving;

2

, If you encounter someone in front of you while driving, you should send a signal

5 m

away;

3

The driving speed in the factory shall not exceed < /p>

15

km/h

, factory doors, elevators, corners, crowded areas, narrow passages, etc.

Hourly speed in other complex areas No more than

10 km/h

;

4

When driving, the lowest point of the cargo should be above the ground

0.3m~0.4 m

;

5

,

Do not turn too sharply

, to prevent

the tendency of "

free turning

"

;

6

< p> ,

Go up and down slopes slowly and at a constant speed

Do not turn on slopes

7

, Do not cross Driving on a slope, when the slope is greater than

10%

, the vehicle should be driven in reverse when going downhill;

8

Forklift personnel carry goods When driving forward, if large or heavy goods come into the driver's sight, you should reverse the vehicle

.

5. Observe the following rules during operation: /p>

"

Eight Don'ts

"

1

Single fork operation is not allowed.

2

It is not allowed to lift the goods and drive them for long distances.

3

It is not allowed to pick up the goods by using a fork to lift the pallet.

4

It is not allowed to use forks to directly transport chemicals, flammable products and other hazardous chemicals.

5

It is not allowed to use inertial force to pick up the goods.

6

It is not allowed to use braking force to release round or easy-to-roll objects.

7

It is not allowed to bring people to work on the pallet or fork. It is strictly forbidden to stand under the fork after the fork is raised.

8

It is not allowed to drive sideways on sloped roads.

Six

.

Precautions

Combined with the above basic operations and based on the use of our company's forklifts, we should pay attention to the following points

p>

1.

When driving a forklift at the entrance and exit of the workshop, you must slow down, watch and blow the horn.

2.

As a special motor vehicle, nine out of ten accidents occur quickly,

so our current forklift driving speed needs to be

Increase control.

3.

Before starting the forklift, confirm whether the load is firmly fixed and whether the forklift gear is in neutral.

4.

Dare to say no to driving without a license or driving illegally. When making an advance, how can we ensure the safety of the funds?

Just leave it to the funder. You only need to pay a service fee for the advance, which is basically less than a thousand dollars, and the funds are limited. Guaranteed, it takes about 1 week for the capital verification report to be issued

The difference between the forklift operation certificate and the safety production operation certificate

The difference between the forklift operation certificate and the safety production operation certificate:

Forklifts are special equipment, and their special equipment personnel operation certificates are uniformly owned by the quality supervision department. The safety production operation certificate is handled by the safety supervision department or the safety production management department. How to ensure safety