Lightweight partition panels?

First, let’s have an intuitive impression of energy-saving and environmentally friendly lightweight partition materials. Currently, the common lightweight partition walls on the market can be divided into lightweight partition boards, lightweight brick partition walls, glass partition walls, skeleton partition walls, movable partition walls and aerated concrete block partition walls. At first glance, there are many types, but in terms of their functions, they are all for better space planning. Let’s briefly talk about the two types of lightweight partition boards and lightweight brick partitions.

▲ Cross-sectional view of lightweight partition board. As a new type of energy-saving material, lightweight partition panels not only have thermal insulation, sound insulation, breathable humidity control, and fire protection, but also have the advantages of rapid construction and reduced wall costs. During installation, you only need to stand the boards up, apply a small amount of caulking mortar on the male and female falcons and assemble them together.

▲Because the installation is very convenient and the material loss rate is low, the construction of lightweight partition boards is not difficult. Two people can carry a 1.49-square-meter wall panel easily. At the same time, move the mortared wall panels to the assembly position and stand them up, align the baseline position up and down, and use a pry to lift the wall panels from the bottom and use force to make the panels close to each other.

▲After completing the installation of the wall panels, correction and nailing are required. Use a straight ruler to check the flatness and verticality of 2 meters, adjust and correct with iron levers, and then use wooden wedges and steel bars to fix them up and down. . The connection between wall panels must be anchored with Φ6×200mm steel bars diagonally driven at 45°. After correcting both sides with 30×30mm wooden wedges, use an impact drill to drill holes in the middle of the tenon or groove surface at a 45° angle, and then anchor with Φ6×200mm steel bars.

▲The picture above is the "component" of a lightweight brick partition wall, which is water-resistant and heat-insulating: a lightweight brick partition wall is made of lightweight bricks or lightweight blocks built with a special adhesive. Non-load-bearing walls used in building partitions. Because of its light weight, high strength, water resistance, impermeability, sound and fire insulation, thermal insulation, and very fast construction.

▲The absolute dry bulk density of lightweight partition brick walls is 500~600kg/m?, which is 1/4 of ordinary concrete, 1/3 of clay bricks, and 1/2 of hollow bricks. It is similar to wood and can Float on water. It can reduce the weight of the building and significantly reduce the overall cost of the building. Fire resistant to 700 degrees, it is a Class A non-combustible refractory material. The fire resistance of a 100mm thick wall can reach 225 minutes, and the fire resistance of a 200mm thick wall can reach 480 minutes.

▲In terms of waterproofing, because the material is composed of many independent small pores, it absorbs water and conducts moisture slowly. The time required to absorb water to saturation for the same volume is five times that of clay bricks. When used in bathrooms, ceramic tiles can be directly pasted on the wall after interface treatment. If you are not very clear about the materials inside the wall, you can also read this article about red bricks, cement, wall building, and reinforcement to talk about villa decoration that you don’t know! Find out more!

▲Usually during the construction stage, new walls need to be built with staggered joints and multiple steel bars are used at the connection between the load-bearing wall to increase the firmness of the wall and avoid cracks in the corners. A new light brick wall should be added with a circle of steel bars every 50 centimeters or so. Two steel bars in each circle should be placed in parallel. The steel bars should be inserted into the old wall at the joint and be the entire length of the new wall. Moreover, the corner area must be the entire length. A steel bar bent over.

▲ Clever partitions make functional distinctions clearer without interfering with each other: After analyzing two common types of partition materials, the editor will talk about the role of lightweight partitions in differentiating functions at home. If your new home is more A large, spacious space may appear too empty if not partitioned off. You can take a look at this collection as a reference for the form of partitions: partitions are continuous, boundaries are not boundaries, there must be one suitable for you

▲Especially for the living room and dining room, if you use lightweight partitions , adding a cleverly shaped small wall in the outer area of ??the restaurant, cleverly dividing the large pattern, and the wall space is also wasted. The wall cabinets and shelves set close to the wall greatly increase the storage function of the area.

▲On the other hand, the dining room and the kitchen are in the same space. In order to block some unnecessary oil fumes, a moderately sized partition wall was specially built between the two. The entire home decoration style is simple and simple, which very well enlivens the atmosphere.