What is used to clean the crystal lamp?

What is used to clean the crystal lamp?

Crystal lamps have always been very popular with people. There are many styles of crystal lamps with good decorative effect, but the installation of crystal lamps is more troublesome and there are many parts, so it is generally necessary to find a professional installation master to install them. What is used to clean the following crystal lamps?

What should I use to clean the crystal lamp? 1 1. You can wipe the crystal lamp with a towel dipped in glass water, which will wipe off the dust. 2. If there is oil stain on the crystal lamp, clean it with hot vinegar, so that the oil stain can be wiped off quickly. 3. If you want to make the crystal lamp brighter, you should wipe it with white vinegar, mix the white vinegar and water evenly according to the ratio of 1:3, then soak it with a towel and twist it into a semi-dry state, and then wipe the surface of the crystal lamp, so that the crystal lamp will be very bright after wiping.

What are the precautions when cleaning crystal lamps?

1, when we clean the crystal lamp, we must wipe it carefully, so as not to break the accessories and some decorations beside the crystal lamp.

2, and before cleaning, you should first spread a thick carpet or old clothes that you don't wear. Because when you clean the crystal lamp, it is easy to break it. If the crystal lamp falls on the floor, it will break. At this time, it will be very troublesome to clean up, and it will also prick the hand. If we take good measures on the ground, even if the crystal lamp falls and breaks, it is easy to take care of it.

3. When wiping the crystal lamp, be sure to wear gloves to avoid leaving stains and fingerprints on the crystal lamp. And when wiping, you can better check whether the crystal lamp is wiped clean.

4, but when wiping the lamp holder, be sure to clean it with a lint-free rag. If hair loss occurs, the overall aesthetics will be affected to some extent. Moreover, the water absorption of the rag must be strong, otherwise the water stains left on the crystal lamp will make the crystal lamp rust due to moisture.

What is brighter for crystal lamp cleaning? 2 Quick crystal lamp cleaning skills.

1, special cleaner

The surface of the crystal lamp can't be cleaned with ordinary detergent. For example, cleaning with clear water can not completely clean the stains on the surface of the crystal ball, but it will also affect the brightness of the crystal, because the brightness of the crystal lamp comes from its crystal clear material. If you use an incorrect cleaning agent, it will damage the surface of the crystal lamp and affect its brightness. Therefore, you must choose the appropriate cleaning agent to clean the crystal lamp.

There is a special crystal lamp cleaner on the market, which is very convenient to use. Just spray it on the surface, the dust and dirt on it will be taken away in the evaporation of the cleaning agent, and then wipe the surface of the crystal lamp with a wet rag, which is simple and convenient to clean.

2. kerosene

Kerosene can be used to clean crystal lamps. Brush the crystal lamp with an old toothbrush dipped in kerosene, and the stubborn dirt on the surface of the crystal lamp can be cleaned quickly. If the crystals can be taken out one by one, it would be better to soak them in kerosene. After kerosene cleaning, brush it with washing powder water again, and then clean it with clear water.

Step 3 add water to vinegar

Add a proper amount of water to white vinegar, then soak a hot towel in it, twist it into a semi-dry state, and gently wipe the surface of the crystal lamp, so it is easy to clean.

4, particle spray degaussing quick-drying cleaning method

This washing method is very professional. Generally, it is the equipment for cleaning professional crystal lamps. Adopt imported cleaning ingredients to clean and degauss lamps. There is no need to disassemble them in the whole process, and the cleaning speed is very fast. Washing dishes is like new.

What is used to clean the crystal lamp?

1 First, prepare necessary tools, equipment, cleaning agents, etc. If it is a large chandelier, it is necessary to prepare high-temperature steam spray guns and other mechanical tools and professional operators. Otherwise, the crystal lamp may be damaged.

2. Spray professional crystal lamp cleaner evenly on the crystal surface, and pay attention to spray it on every surface of the crystal. Then wait for about 5 minutes, and then the cleaning agent fully penetrates into the bottom layer of the surface stain, so that the stain and oil can dissolve and peel off.

3. Then clean the crystal surface once with clear water. If the crystal area is large, it can be wiped with a wet cloth. The crystal area is small and there are many crystal beads. Just put the clear water in the mist washer and spray it with high pressure to wash it.

4. After cleaning, the crystal lamp can be used after air drying. Large crystal lamps can be dried by a hair dryer to speed up drying. Precautions for crystal lamp cleaning When cleaning crystal beads, if the grade of crystal beads used before is relatively low, friends with conditions should replace them with higher grade crystal beads. The higher the grade, the better the dust-proof treatment of the product surface, which is not easy to be damaged by lampblack, and can remain crystal clear after long-term use. If it can't be replaced, it is necessary to shorten the cycle of cleaning the crystal lamp.

What is used to clean the crystal lamp? 3. Installation steps of crystal lamp

1, check

Crystal lamp has many parts, such as back strip, light bulb, light board and so on. When installing, check whether the parts are complete. In addition, installation tools, such as electric drills, screwdrivers and wrenches, should be prepared.

Step 2 fix the strap

The back strip of the crystal lamp is used to fix the lamp. When installing, you can first determine the installation position on the ceiling with the back strip, then drill holes with an electric drill, fix the back strip on the top surface with expansion screws, then fix the lamp panel on the back strip with screws, and support the whole lamp with nuts, so that the main body of the crystal lamp is fixed.

Step 3 connect the wires

Connect the crystal lamp wire with the wire reserved in the ceiling. For safety, please turn off the power switch at home when connecting the wires to avoid the danger of electric shock. In addition, neutral wire and live wire should be connected correctly and fixed with insulating tape.

Step 4 install the light bulb

Fix the light bulb on the lamp board and turn off the power supply. After all bulbs are fixed, test them to ensure that all bulbs can be used normally. If there is any problem, check the reason in time until it can be used normally.

Step 5 Install accessories

There are many kinds of crystal lamp accessories, which can be connected in series according to the drawings. As for how many strings of ornaments need to be hung and how to match their lengths, there are instructions on the drawings. You can install them according to the instructions on the drawings.

Second, the crystal lamp cleaning method

1. Prepare tools such as ladders, rags and cleaning agents, and then turn off the power. In order to prevent the ladder from scratching the floor, you can put a sponge pad under the crystal lamp.

Climb up the ladder, take down the crystal balls one by one, and put them in the basin for cleaning. Remember the position when holding the crystal ball for easy installation.

3. After the crystal ball is put into the basin, it can be washed with detergent to clean the stains on the surface.

4. After the crystal ball is cleaned, clean the electroplated lamp holder with a rag and then reinstall it.