How to install ceiling lamps? Installation methods and maintenance skills of ceiling lamps

Ceiling lamps may be used in living rooms, bedrooms, kitchens, and bathrooms during home decoration. So how to install ceiling lamps? The following editor will tell you in detail:

How to install LED ceiling lamp?

1. Turn off the power supply switch of the lamp.

2. Open the lamp shade, and use screws and expansion tubes to fix the induction lamp to the wall or ceiling.

3. Connect the power supply cord and the lamp power cord. First, peel off 5-7mm long wire ends from the power supply cord and lamp power cord, then twist the exposed metal wires together and wrap them with electrical insulating tape.

4. Align the lampshade with the lamp and buckle it on the lamp, push it in hard and fix the lampshade on the lamp.

LED ceiling lamp maintenance methods:

1. After buying the lamp, do not rush to install it. You should carefully read the mark of the lamp and read the installation and operation instructions, and then Install and use lamps according to the instructions in the manual, otherwise danger may occur.

1. Replace the aging lamp in time according to the light source parameters provided by the sign. If you find that the ends of the lamp are red, the lamp is black or there is a shadow, or the lamp fails to light up, you should replace the lamp in time. tube to prevent unsafe phenomena such as ballast burnout;

2. During cleaning and maintenance, be careful not to change the structure of the lamp, and do not replace the parts of the lamp at will. After cleaning and maintenance, you should Install the lamps as they are, and do not miss or install the wrong lamp parts;

3. When using LED lamps, try not to turn them on and off repeatedly, as this will greatly shorten the service life of the LED lamps.

How to install a kitchen ceiling light?

1. First drill a hole in the cement ceiling of the kitchen, and then knock the plastic gecko into the ceiling hole (if it is a suspended ceiling, it can be placed directly on the ceiling Fix the ceiling plate with screws)

2. Connect the power to test the lamp. After normal operation, remove the test light wire, and connect the power cord to the original test light wire position of the ceiling plate. Make sure that the power cord Valid connection, pay attention to distinguish between zero and live wire.

3. Put the flat washer on the screw, and screw the screw clockwise through the hole in the floor into the plastic gecko compression ceiling plate.

4. Buckle the lampshade onto the ceiling plate, and rotate the lampshade clockwise until the lampshade is fixed on the ceiling plate.

How to clean the kitchen ceiling lamp:

After using the ceiling lamp for a period of time, you should pay attention to cleaning. Cleaning and maintenance can extend the service life of the ceiling lamp. The biggest problems in the kitchen are oil smoke and moisture, so you should pay attention to the following points when cleaning the ceiling lamp:

1. The kitchen is humid, which may cause the ceiling lamp to leak electricity, so be sure to turn off the power first and pay attention Do not wipe the lamp holder with a wet cloth.

2. When cleaning the ceiling lamp, you should put light-colored cotton socks or cotton gloves on your hands, gently wipe the lamp, and do not move the parts inside the lamp at will.

3. Cleaning the lampshade can be carried out according to the material. If it is made of glass, it can be wiped carefully with a small soft cloth. If it is made of plastic, it can be removed and cleaned.

4. To clean the dirt on the lamp holder, you can first remove the dust on the surface, and then wipe it with cotton cloth dipped in toothpaste. Do not let moisture stay on the lamp holder.

How to install the ceiling lamp in the living room?

1. The two wires connected to the power supply line of the ceiling lamp in the living room should have good electrical contact, and should be wrapped with black tape respectively, and Keep a certain distance, and if possible, try not to put the two wire ends under the same piece of metal to avoid short circuit and danger.

2. Rooms with higher floors or ceilings with vibrations are suitable for installing ceiling lights. When installing ceiling lamps in masonry structures, embedded bolts should be used, or expansion bolts, nylon plugs or plastic plugs should be used to fix them; wooden wedges should not be used. And the load-bearing capacity of the above-mentioned fixings should match the weight of the ceiling lamp. To ensure that the ceiling lamp is firmly fixed and reliable, and to extend its service life.

3. If a screw lamp holder is used in the ceiling lamp, the following two points should be paid attention to when wiring: the phase wire should be connected to the terminal of the center contact, and the neutral wire should be connected to the threaded terminal. Above; the insulating shell of the lamp head should not be damaged or leakage to prevent electric shock when replacing the bulb.

4. Educate children not to throw balloons and other objects at lamps indoors to prevent hanging decorations from falling and injuring people or affecting the decorative effect of the lamps. When installing a ceiling lamp, special attention should be paid to the reliability of the connection between the lamp and the installation. The connection must be able to withstand a suspension equivalent to four times the weight of the ceiling lamp without deformation.

Living room ceiling lamp maintenance tips:

1. When installing the ceiling lamp, you must consider the roof condition of the home. If it is a masonry roof, use embedded bolts. Or use expansion bolts, nylon plugs, plastic plugs, etc. to fix them. Wooden wedges cannot be used. Do not hang too many decorations on the lamps, otherwise they will fall down and injure people if they exceed the carrying capacity.

2. Pay attention to the indoor temperature, especially crystal ceiling lamps, which often stipulate a specific ambient temperature. Too high or too low a temperature will affect its life, so the temperature must be kept appropriate.

3. Lamps should be checked regularly. If the lamp pins have poor contact or the starter is loose, they should be reinstalled and adjusted in time.

4. Although the ceiling lamp is close to the ceiling, some electromagnetic reactions will still absorb dust in the air when the light is turned on. Lighting can also attract mosquitoes to fly into the lampshade, so remember to maintain a clean home environment and clean lamps frequently to prevent the lights from dimming.

5. Be careful not to let hard objects touch the lamp, otherwise it will easily scratch the surface of the lamp, or even cause the lamp body to break. If you want to move the lamp, you must maintain balance and be careful not to let the ceiling lamp fall to one side.