How to make the meter run slower?

Question 1: How to make the meter rotate slower? 3 methods for reference:

1. Tilt the vertically installed meter 15°

2. Open the wiring cover of the ammeter, and loosen one of the screws of the current wiring card on the upper left side of the terminal block (horizontal clamp) (note that there is electricity, please use an insulated screwdriver). At this time, the meter is under heavy electrical load. Counting, load hours are not counted.

3. If you are more professional, you can open the meter casing and loosen the top screw above or below the center of the rotating disk. This method is best used in conjunction with the first method.

Question 2: How to make the meter run slowly? Please don’t... The answer is: There is a screw on the left side of the watch case, which is 1CM in diameter. It is used for calibrating the meter. Yes, you can use the flat mouth to turn it clockwise, and it will run slower, but at the slowest it can only reduce the power by about one kilowatt hour per day. If you want to use only ten kilowatt hours per month or much less, you have to use the second One method is to change the situation, take a small 600-revolution watch, that is, a meter that turns 600 times to get one kilowatt-hour of electricity. The larger the number, the more times the same electricity needs to be turned. Take out the gear combination inside and follow Change the gear combination of your big watch. Your big watch must be the 200-rpm one. After changing it, haha, your electricity bill will be 1/3 of the original one. Don’t worry, the parts in the meter are all standard parts. , it is definitely worthy of it, but it is troublesome to completely remove the watch during manipulation. Once it is replaced, even if someone from the meter factory comes to check, he will not be able to find the reason unless he takes the watch back and tests it on the tester. Generally, electric power bureaus do not have this equipment.

Question 3: How to make the meter run slower. Simple, it is best not to watch. The more detailed the better What kind of meter? Mechanical watch? Electronic watch? If it's a mechanical watch, you can. Open the wiring cover. There are two small screws on the live wire. Loosen the second screw and pull out the small connecting piece. Do not touch the second screw, and the meter will not rotate. The landlord can do it after reading the meter, use it for 20 days out of 30, and then connect it, saving 2/3 of the electricity. Changing the wires is useless. A DD862-4 or other electric meter can measure even when it is reversed, nor can a magnet. The turntable is made of aluminum, so it is useless. If it is an electronic meter, haha, there is no way. It is too obvious. It is two live wires connected to one wiring hole, the first hole

Question 4: Is there any way to make the meter turn slower to tell you that it is stolen? There are two ways to use electricity. 1. Aren’t there 4 electric meter wires? Take 1 and 3 out of the meter and connect them. If it doesn’t work, use 2 and 4 in the same way. This way the meter will not rotate for a month. Just do this for a few days and it will be fine. 2. When making a plug board, do not use a plug. Connect one wire to the live wire and the other to the ground. It is best to see where there are nails buried underground. Your plug board is a stolen one. The meter will not turn, but the power is low. Look at the TV fan or something

Question 5: How can you make the meter run slowly if you don’t move the meter? Measures to prevent electricity theft with single-phase meters In order to improve production safety and economic benefits, and protect their own interests, Taiwan District Management Personnel need to conduct a comprehensive and thorough verification and cleaning of all user meters and lines in the entire jurisdiction at regular intervals. After the meter is calibrated, you need to pay attention to the following points when installing it: 1. When installing the meter, try to unify the colors of the wires, and wires of different colors are connected to different phase wires. And absolutely ensure that terminal 1 of the meter is the live wire and 3 is the neutral wire. After the incoming line is installed, in order to prevent some users from secretly disconnecting the main neutral line for private grounding purposes, use a test pen to measure whether there is any induction current at terminals 3 and 4 of the incoming line. If not, it means that the line is normal. If there is, it may be The main line to the meter has been disconnected. It is necessary to immediately find the location of the disconnection and analyze whether it was artificially disconnected based on the fracture location. If it is artificially disconnected, the user will be listed as a key inventory target. If everything is normal, connect the meter terminals. After the wires are connected, turn all the terminal screws and the meter connection screws again. And make sure it is firmly connected. 2. Cover the meter terminal cover and seal it. When sealing, thread the sealing line and tie a knot, try to shorten the sealing line, move the sealing block to the knotted area, and tie the seal. Choose a thin paper seal, write the user's name and paste it on. 3. Check whether the user's leakage protector can disconnect the power supply normally. If it is damaged, it must be replaced immediately. If normal, use a test pen to measure whether the two terminals of the outlet wire are one zero and one fire. Disconnect the power supply and connect it to the user's home wiring, then turn on the switch to see if the power supply is normal.

If the leakage protector fails to close, it means there is a problem with the wiring in the user's home, and the user's wiring should be checked. Don't not install it because you are afraid of trouble, otherwise two results may occur, and both of these reasons will cause the Taiwan District General Insurance to be unable to be put into operation: (1) The user's home is privately installed with ground wires to steal electricity. (2) A fault in the user's home wiring may cause a safety accident. 4. For stations that do not have leakage protectors installed, they should prepare their own leakage protectors to check user lines. 5. Check the meter box to see if it is intact or defective. If it is not sealed. When sealing, thread the sealing line and tie a knot, try to shorten the sealing line, move the sealing block to the knotted area, and tie the seal. Choose a thinner paper seal, write the user's name, the location number of the station and the electricity usage slogan and paste it on. And promote some basic knowledge about electricity usage to users. 6. After the meter is cleaned, it is time to conduct monthly inspections. As a Taiwan area manager, the task is not completed just by collecting the electricity bill. The most important thing is to manage the station area well to improve line losses and ensure safety. Make time to visit the Taiwan area more often, especially at night when the phenomenon related to drought relief is more serious. Try to make as much noise as possible in the jurisdiction to let users know that you are not only reading meters and charging fees, so that electricity thieves will not dare to steal electricity blatantly. 7. When reading the meter every month, focus on checking whether the lead seal and paper seal of the meter are damaged. Is there anything on the main line that shouldn't be there? It would be best if several Taiwan area managers could be joined together to set up a mutual aid group to go to the Taiwan area to check lines and deal with power thieves. This is both safe and a deterrent to electricity thieves. We strive to capture one electricity thief in each district and send them to the judicial department to serve as a warning to others. Several people joined forces and went to various stations to cut down green trees and clear obstacles, and clean porcelain bottles on electric poles. Do the opposite!

Question 6: How can I make the meter run slower? The speed of the electric meter is set by the manufacturer according to the power consumption. You can't adjust this. Besides, even if you can adjust it yourself, it is illegal and constitutes electricity theft.

Question 7: A simple way to make the meter run slower. What kind of meter? Mechanical watch? Electronic watch? If it's a mechanical watch, you can. Open the wiring cover. There are two small screws on the live wire. Loosen the second screw and pull out the small connecting piece. Do not touch the second screw, and the meter will not rotate. The landlord can do it after reading the meter, use it for 20 days out of 30, and then connect it, saving 2/3 of the electricity. Changing the wires is useless. A DD862-4 or similar electric meter can measure even when it is reversed, nor can a magnet. The turntable is made of aluminum, so it is useless. If it is an electronic meter, haha, no idea, it is too obvious, just two live wires connected to one wiring hole, the first hole

Question 8: How can I make the meter run slowly and use less electricity, or not Electricity usage

Question 9: How can I make the electric meter run slower? One is to disassemble the meter and adjust it by changing the resistor on the circuit board that is specially used to adjust the speed of the meter (the normal practice in the meter calibration room). The other is to steal electricity, and check the stolen electricity online, but it is risky. , you steal a lot, they have district meters and can compare your behavior,

Question 10: How to make the meter run slower and use less electricity

Development Some good electricity usage habits can save electricity

The meter will run slower

Best wishes