Installation details of foot valve squatting pan How to install squatting pan is correct.

Everyone is familiar with the decoration and installation of squatting pans. If it is a squatting pan with a bottom valve, it is necessary to determine the reserved size of the bottom valve and a series of details in the later installation. Here is a detailed installation diagram of the foot valve squatting pan, and how to install the squatting pan is the correct related content, which can be used as a reference by friends in need.

Detailed installation drawing of squatting pan with bottom valve

According to the sewage outlet of installed products, the sewer pipe is reserved at an appropriate position far away from the wall, and the distance between the entrance of the sewer pipe and the ground is determined.

The depth of the pit reserved under the ground for installing the squatting pan is greater than the height of the toilet.

Put the connecting rubber plug into the water inlet hole of the squatting pan and clamp it. Coat a layer of glass glue or putty on the outer edge in contact with the water inlet of the squatting pan, and put the glue into the water inlet to make it seal well with the rubber plug to prevent water leakage.

Coat a layer of glass glue or putty on the edge of the water outlet of the squatting pan, put it into the inlet of the sewer pipe and tighten it, and erect the toilet horizontally with cinder or other fillers.

Open the water inlet system and check whether there is water leakage at each joint. If there is water leakage, check the situation at each joint. Until the problem is solved.

How to install the squatting pan is correct.

Measure the size of the squatting pan first, and reserve the installation position according to the size. First, fill the heart with mixed mortar at the installation position, and it is forbidden to install it with cement, so as to avoid cement condensation and expansion that may crush the squatting pan. Apply a layer of asphalt or butter on the installation surface of the squatting pan to isolate the squatting pan from the water mortar and protect the product from bursting. Apply adhesive or clay to the sewage outlet of the squatting pan and the reserved opening of the downspout, and connect the sewage outlet of the squatting pan with the reserved opening of the downspout to correct the position of the squatting pan. Brick-laying fixed squatting pan should reserve a gap for filling gravel soil. When the glue dries, try to flush it into the squatting pan to see if there is any leakage at the interface. Next, fill the gravel soil between the ground and the squatting pan. It is forbidden to fill in cement concrete. Seal the gap with bricks, and then paste cement mortar and tiles outside the bricks.

Flushing valves are divided into manual flushing valves and pedal flushing valves. The installation height of the water tank should be away from the toilet water ring 1.8m, and the water pressure should be 0. 14-0.55 MPa to ensure good flushing effect. For squatting pans with water storage ports, there should be no water storage ports in the sewer pipes, so as not to affect the flushing function. For squatting pans without storage inlet, storage inlet should be set in the pipeline to prevent odor. In the environment below zero degrees Celsius, water cannot be stored in the cavity of the elbow of the squatting pan, otherwise the water may freeze and expand, crushing the toilet.

Second, matters needing attention

Put the connecting rubber plug into the water inlet of the squatting pan and clamp it. Coat a layer of glass glue or putty on the outer edge of the water inlet of the squatting pan, and insert the glue into the water inlet to make it seal well with the rubber plug to avoid water leakage. It is necessary to coat a layer of glass glue or putty on the edge of the water outlet of the squatting pan, put it into the entrance of the sewer pipe and tighten it, and use coke residue or other fillers to stand the squatting pan horizontally.

Connect the water pipe of the water inlet, insert the connecting rubber plug into the water inlet hole of the squatting pan and clamp it. Fortunately, the outer edge of the squatting pan touching the water inlet hole is coated with a layer of glass glue or mortar, and the water inlet pipe is inserted into the water inlet hole to make it seal well with the rubber plug to prevent water leakage. Don't test the water immediately after installation, wait until the cement mortar is dry.

Regarding the detailed installation diagram of the foot valve squatting pan, how to install the squatting pan is no problem, so I will take you here.