Safety management system of electricity consumption in shopping malls

1. Basic knowledge of safe electricity use for staff in specialty stores and shopping malls:

1, all electrical equipment must have safety certification, and regular safety inspection.

2. In any case, it is not allowed to identify whether the conductor or equipment is charged by hand, and a test pen can be used in the 380/220 volt system;

3, replace the fuse or safety inspection, maintenance of electrical equipment, should first cut off the power supply, to avoid live work, fuse can't be replaced by copper, iron wire.

4. Install and regularly check the contact and leakage protection switch.

5. When moving electrical equipment, turn off the switch of the electrical equipment and cut off the power supply.

6. Don't pull, pull or change wires, patch panels and sockets without permission, don't change or repair electrical equipment without permission, don't install or use unauthorized appliances (from heating equipment to mobile phone chargers) without permission, and don't hang things on wires or dry clothes.

7, change, mobile electrical appliances, equipment, wires, mobile live display cabinets, island cabinets, cabinets, should be reported to the electrician to assist in the completion.

8, cleaning the live equipment, should replace the equipment switch, cut off the power supply cleaning, pay attention to check whether the wire is damaged, if any, it must be repaired immediately.

9. The ground wire is very dangerous. After the wire is squeezed, trampled, rubbed, pulled and soaked after landing, it is easy to leak electricity and cause danger.

10, do not wet or soak electrical appliances, lines and plugs.

1 1. Note that wet weather in rainy season will reduce the insulation performance of electrical appliances, lines and plugs, thus increasing the risk of electric shock.

12, plug, socket, electrical appliances, equipment, lines, etc., must immediately cut off the power supply at the same level or higher level, and immediately report to the electrical department for processing.

13. It is dangerous to touch electrical appliances with wet hands. Unplug the plug and touch the electrical appliances and wires with wet hands, which may lead to electric shock due to the degradation of insulation performance. Do not wipe live equipment with a wet cloth.

14. Sufficient safe passages and working spaces should be left around electrical equipment and electrical lines. Flammable, explosive and corrosive articles should not be stacked near electrical devices.

15, electrical equipment shall not be covered with clothes, towels, newspapers and magazines, cartons, plastic sheets, sundries and other items at will.

16. loose connection between plug and electrical equipment was found; When the plug is not firmly connected with the seat and the seat is not firmly connected with the fixture, it should be repaired in time. Keep electrical equipment ventilated and cool. If you smell burning, and find that the wires are damaged, the appearance of electrical equipment is damaged, and the equipment is abnormally hot and noisy, you should immediately cut off the power supply and report the maintenance and inspection. Do not use it with faults.

17, electrical appliances, lines, etc. In case of fire, cut off the power supply as soon as possible, call the police immediately and use dry powder or carbon dioxide fire extinguisher nearby to put out the fire. Most electrical fires after cutting off the power supply can be put out as ordinary fires.

Note: Never use water to extinguish the fire of live equipment.

18. Before closing the store, the exit salespeople cut off the electrical equipment of the store in charge, turn off the display cabinets and counter lights, and cut off the counter power supply. We must know that a small oversight may lead to a disaster.

19, cooperate with the acceptance of electricity inspection work, and do not push the Committee or make things difficult for inspectors.

20, master the knowledge of electricity safety, in the work to protect the interests of shopping malls and employees, leaving no security risks, do not hurt yourself, don't hurt others, protect yourself from being hurt by others.

2. Power operation procedures

1. Open the main brake before opening it.

When power is cut off, disconnect the sub-brake first, and then disconnect the main brake.

2. The use of master switch and leakage protector

The "T" test button should be pressed once a month. When pressed, the protector will trip automatically, and the black reset button will stand out, indicating that the leakage protector is normal and can play a protective role. On the contrary, the leakage protector doesn't work and needs to be replaced. When reclosing, the prominent black reset button must be reset, otherwise the brake will not close.

3. The use of metal halide lamps

When the metal halide lamp is powered off, it must wait 15 minutes before it can be powered on again. It is forbidden to use it immediately after cutting off the power supply.

References:

/view/239503 196 BD 97 f 192279 e99a . html？ From = rec&pos = 4 & weight = 2 & final weight = 2 & count =5.