6 safety production self-inspection report forms

Safety production self-inspection report 1

In order to effectively do a good job in the safety production work of our project department, conscientiously implement the safety production responsibility system and increase hidden dangers Investigation and rectification to prevent the occurrence of safety production accidents. Our project department conducted a safety inspection and now reports the inspection status as follows:

1. Basic situation

Our project department conducted a safety self-inspection on October 20 to find hidden dangers and implement Corrective measures. Suggestions for rectification were put forward for the project's existing safety production management system, inadequate job operating procedures, special operators working without training, hazardous chemical raw material inventory not meeting requirements, and non-standard electrical appliances and wiring.

2. Problems

During this safety production inspection, the main problems found are:

1. Safety production management system and job operating procedures , The safety management organization is not sound, and responsibilities are not assigned to people.

2. The project department failed to provide adequate safety education and training for employees, and special operations personnel did not obtain special operation qualification certificates and do not receive special training as required before starting work.

3. Electrical appliances and circuits are not regularly checked, the circuits are aging, the wiring is not standardized, the temporary electricity is connected privately, the knife switch is not covered, etc.

4. Fire-fighting equipment is insufficiently equipped, expired, and not placed in a conspicuous location.

3. Rectification measures

In response to the problems detected above, our project department rectified them on time, reviewed them on schedule, and tracked and rectified them to ensure that the rectifications were in place.

1. Project department managers should establish awareness of production safety. It is necessary to strengthen measures and conscientiously implement the safety production responsibility system. Project department managers must include safety production work in their important agenda, and the top leaders must personally grasp it. It is necessary to increase the intensity of safety production work, conscientiously implement the policy of "safety first, prevention first", adhere to the principle of who is in charge and who is responsible, implement the safety production work responsibility system at all levels, and be practical and meticulous.

2. Abide by rules and laws, and establish and improve safety production rules and regulations. Establish and improve the safety production work rules and regulations, job operating procedures, and organizational structures, so that there are rules to follow, laws to follow, organization and implementation, system implementation, and measures implementation. At the same time, we must do a good job in promoting, educating and training workers on production safety, and enhance workers' awareness of production safety and legal concepts.

3. Conduct frequent inspections, carefully investigate and rectify hidden dangers. The inspection work of our project department on production safety must be regular, institutionalized and standardized, and the word "diligence" should be mainly reflected in the work. We must frequently inquire, supervise and inspect frequently. It is necessary to urge and speed up the rectification of potential safety hazards raised during inspections, nip hidden dangers in the bud, and reduce the occurrence of safety production accidents.

4. Strict discipline and serious accountability. The project department must do a good job in preventing production safety accidents and prevent the occurrence of various accidents. Once an accident occurs, the accident reporting system must be conscientiously implemented and reported in a timely manner step by step.

Safety production self-inspection report 2

In order to thoroughly implement the 165th executive meeting of the State Council and the spirit of important instructions from central leaders, learn lessons from accidents, implement safety responsibilities, and strengthen To take preventive measures, we must do a good job in the company's safety production work, effectively prevent and resolutely contain accidents, and the company's Safety Committee shall, in accordance with the requirements of the "Notice on Further Improving Safety Production Work", inspect the implementation of safety responsibilities and systems, safety publicity, education and training situation, implementation of safety responsibilities and rectification of hidden dangers, and emergency plan formulation and drills. The specific self-examination contents are as follows:

1. Implementation of safety systems and responsibilities

The company’s production safety management system filing and archiving work is complete, each system is sound, the emergency plan is complete, and drills are feasible , the assessment results of various operating procedures are good, cadres and workers at all levels consciously abide by the system and procedures, and there are no violations.

The company leaders signed the "Team Leaders' Responsibility Letter for Safety Production" with the leaders of each front-line production team. The leaders of each team have a strong awareness of production safety and earnestly implement the idea of ??"everyone is responsible for production safety". Employees conscientiously perform their respective safety production responsibilities at their posts, providing a strong guarantee for the implementation of various safety production measures.

2. Safety publicity, education and training

The company organized and carried out various forms of publicity and education activities according to the overall arrangements of superior leaders. The first is to carry out in-depth legal education and publicize and learn laws and regulations such as the "Safety Production Law" through holding safety production meetings and other forms. The second is to enrich the form of publicity activities by organizing employees to conduct safety knowledge education, participate in fire safety drills and chlorine leak drills, and use bulletin boards, banners, slogans, etc. to promote various safety knowledge and safety regulations. It enables the majority of employees to have an in-depth understanding of safety and pay extensive attention to safety, which greatly improves the safety production awareness of all employees.

Through various forms (warning signs, publicity boards, slogans, etc.), employees can understand the hazards and preventive measures in their positions, and clarify the rescue measures when hazards occur. Educate employees on emergency response skills for minor work-related injuries to minimize injuries. Enable employees to skillfully use labor hygiene protective equipment, reduce occupational disease hazards, and prevent the occurrence of occupational diseases. Enable employees to take self-rescue and mutual rescue measures correctly and skillfully in emergencies. The company *** organized 3 safety production knowledge trainings and held 5 safety production meetings to summarize the hidden dangers in safety production, formulate rectification and preventive measures for existing safety hazards, exchange safety work experience, and convey safety production documents , arrange relevant safety work and report safety inspection status.

3. Implementation of safety responsibilities and rectification of hidden dangers

The maintenance records of equipment, pipelines, safety protection devices, platforms, ladders, guardrails, brackets and other protective facilities are complete and effective. The surface of the equipment and pipelines is clean, without damage, cracks, leakage or leakage, and various valves and instruments are normal. Various safety fire-fighting facilities are fully equipped, qualified and effective, and operators wear labor protection equipment in accordance with regulations. Accident cabinets should be set up in toxic and hazardous places to store protective first-aid supplies that are complete and effective, and should be inspected regularly.

The installation and maintenance of electrical equipment are operated by electricians. Non-electricians are not allowed to decorate electrical equipment and lines. There are dedicated personnel to manage accident-prone electrical equipment, and everyone is responsible. When electricians are working, they can be equipped with labor protection supplies as required, work according to operating procedures, and check regularly

Lines and all electrical equipment, and all high-voltage dangerous places, are equipped with protective facilities and warning signs. Non-electrical work Personnel are strictly prohibited from entering the power distribution room or the guardrail of electrical equipment, are strictly prohibited from hanging around, and are strictly prohibited from approaching high-voltage dangerous places.

In accordance with the requirements, members of the Safety Committee team carried out four major production safety inspections in stages (Spring Festival, Spring, May Day, and Safety Production Month). We made rectification and treatment plans for various hidden dangers that were detected, and truly eliminated the hidden dangers of accidents. Conduct a self-examination every month. During the inspection process, we adhered to the principle of xx and carefully conducted comprehensive inspections on weak links and possible problems, focusing on checking whether the safety system was implemented, whether safety measures were in place, whether safety protection facilities and equipment were complete and intact, and whether hidden loopholes and hazards were corrected.

In order to prevent the occurrence of emergencies, the company's safety committee team conducted two emergency accident plan studies for department employees (fire safety study and chlorine leakage safety study). On the basis of the study, Due to the particularity of the unit's production, fire drills for sudden fires and leakage drills for the chlorination system were simulated. The drill focused on examining employees' ability to respond to emergencies, investigation and handling of emergencies, and personnel self-protection measures. Through on-site emergency plan drills, the safety awareness of employees and managers is improved, so that employees clearly understand the importance of safety in production, enhance employees' ability to respond to emergencies, gradually improve and perfect the emergency rescue plan, and improve employees' Emergency response and on-site rescue skills.

4. Existing problems:

1. The company’s safety production materials are not properly classified and organized. Although the company's safety production materials are complete, they are not classified and stored.

2. Safety production education and training are weak. There is not much effort in carrying out safety production education activities, especially the safety production education for drivers is a mere formality, and the improvement of employees' safety production awareness is slow.

3. The company’s safety hazard investigation has not been implemented thoroughly.

5. Next steps

1. Further strengthen the implementation of the classification and sorting of the company's safety production data, ensure that the company's safety production data are accurate and complete, and classify and store them .

2. Strengthen the education and training for company employees and drivers, conduct safety education and learning once a month, implement the learning and education system, continuously improve their safety awareness and sense of responsibility, and effectively maintain the safety order of road transportation .

3. Further strengthen the implementation of the company’s fire protection facility management and increase efforts to investigate potential safety hazards.

Safety production self-inspection report 3

In order to thoroughly implement the 165th executive meeting of the State Council and the spirit of the important instructions of the central leaders, deeply learn from the lessons of the accident, implement safety responsibilities, and strengthen To take preventive measures, we must do a good job in the company's safety production work, effectively prevent and resolutely contain accidents, and the company's Safety Committee shall inspect the implementation of safety responsibilities and systems, safety publicity, education and training in accordance with the requirements of the "Notice on Further Improving Safety Production Work" situation, implementation of safety responsibilities and rectification of hidden dangers, and emergency plan formulation and drills. The specific self-examination contents are as follows:

1. Implementation of safety systems and responsibilities

The company’s production safety management system filing and archiving work is complete, each system is sound, the emergency plan is complete, and drills are feasible , the assessment results of various operating procedures are good, cadres and workers at all levels consciously abide by the system and procedures, and there are no violations.

The company leaders signed the "Team Leaders' Responsibility Letter for Safety Production" with the leaders of each front-line production team. The leaders of each team have a strong awareness of production safety and earnestly implement the idea of ??"everyone is responsible for production safety". Employees conscientiously perform their respective safety production responsibilities at their posts, providing a strong guarantee for the implementation of various safety production measures.

2. Safety publicity, education and training

The company organized and carried out various forms of publicity and education activities according to the overall arrangements of superior leaders. The first is to carry out in-depth legal education and publicize and learn the "Safety Production Law" and other laws and regulations through holding safety production meetings and other forms. The second is to enrich the form of publicity activities by organizing employees to conduct safety knowledge education, participate in fire safety drills and chlorine leak drills, and use bulletin boards, banners, slogans, etc. to promote various safety knowledge and safety regulations. It enables the majority of employees to have an in-depth understanding of safety and pay extensive attention to safety, which greatly improves the safety production awareness of all employees.

Through various forms (warning signs, publicity boards, slogans, etc.), employees can understand the hazards and preventive measures in their positions, and clarify the rescue measures when hazards occur. Educate employees on emergency response skills for minor work-related injuries to minimize injuries. Enable employees to skillfully use labor hygiene protective equipment, reduce occupational disease hazards, and prevent the occurrence of occupational diseases. Enable employees to take self-rescue and mutual rescue measures correctly and skillfully in emergencies.

The company *** organized 3 safety production knowledge trainings and held 5 safety production meetings to summarize the hidden dangers in safety production, formulate rectification and preventive measures for existing safety hazards, and exchange safety work experience , convey documents on production safety, arrange relevant safety work, and report safety inspection status.

3. Implementation of safety responsibilities and rectification of hidden dangers

The maintenance records of equipment, pipelines, safety protection devices, platforms, ladders, guardrails, brackets and other protective facilities are complete and effective.

The surface of the equipment and pipelines is clean, without damage, cracks, leakage or leakage, and various valves and instruments are normal. Various safety fire-fighting facilities are fully equipped, qualified and effective, and operators wear labor protection equipment in accordance with regulations. Accident cabinets should be set up in toxic and hazardous places to store complete and effective protective and first-aid supplies, and regular inspections should be carried out.

The installation and maintenance of electrical equipment are operated by electricians. Non-electricians are not allowed to decorate electrical equipment and lines. There are dedicated personnel to manage accident-prone electrical equipment, and everyone is responsible. Electricians must be equipped with labor protection supplies as required when working, work according to operating procedures, and regularly check circuits and all electrical equipment. Protective facilities and warning signs are set up in all high-voltage dangerous places. Non-electricians are strictly prohibited from entering power distribution rooms or It is strictly prohibited to pull or hang the electrical equipment inside the guardrail, and it is strictly prohibited to approach high-voltage dangerous places.

In accordance with the requirements, members of the Safety Committee team carried out four major production safety inspections in stages (Spring Festival, Spring, May Day, and Safety Production Month). We made rectification and treatment plans for various hidden dangers that were detected, and truly eliminated the hidden dangers of accidents. Conduct a self-examination every month. During the inspection process, we carefully conduct a comprehensive inspection of weak links and possible problems, focusing on whether the safety system is implemented, whether safety measures are in place, whether safety protection facilities and equipment are complete and intact, and whether hidden loopholes and hazards are corrected.

4. Emergency plan formulation and drills

In order to prevent unexpected accidents, the company's safety committee team conducted two emergency accident plan studies for department employees, ( Fire safety learning and chlorine leakage safety learning) based on the learning, simulated sudden fire firefighting drills and chlorination system leakage drills based on the particularity of unit production. The drill focused on examining employees' ability to respond to emergencies, investigation and handling of emergencies, and personnel self-protection measures. Through on-site emergency plan drills, the safety awareness of employees and managers is improved, so that employees clearly understand the importance of safety in production, enhance employees' ability to respond to emergencies, gradually improve and improve emergency rescue plans, and improve employees' Emergency response and on-site rescue skills.

Safety production self-inspection report 4

In order to ensure the fire prevention and theft safety of our company's office environment, according to the arrangements of the company leaders, the person in charge of the comprehensive office led the relevant office personnel to form a safety inspection The team conducted a strict inspection on the fire safety and anti-theft work of the company's office building and the open-air parking lot downstairs on the afternoon of December 12. The inspection results are now reported as follows:

1. Overall safety inspection

The inspection team first inspected the doors and windows, electrical circuits and switches, corridor fire safety passages, fire protection facilities, and environmental sanitation on each floor of the office building. Then the open-air parking lot, green belt and lighting facilities outside the building were inspected. The inspection team conducted a comprehensive inspection and found that the overall situation was good and there were no major safety hazards.

2. Existing problems

1. The doors leading to the terrace on both sides of the roof on the fifth floor are not locked, and the door of the conference room on the fourth floor and an aluminum window in the conference room are not locked. The door lock on the right side of the sliding door of the reading room cannot be locked, and the door lock on the right side of the sliding door of the reading room is damaged. Outsiders can enter and exit at will, which poses a safety hazard.

2. There are piles of debris in the reading room, which are piled up in a messy manner, posing fire safety hazards.

3. The entire building is equipped with only 2 dry powder fire extinguishers, and the shelf life of the dry powder in the fire extinguishers is unknown; the fire hydrants on each floor are locked, but the keys are missing, and it is not possible to check whether the fire hydrants can be used. Normal use. There are fire safety hazards.

4. Some offices on the second floor do not lock their doors after get off work, posing potential security risks against theft.

3. Corrective measures and suggestions

1. Ask a professional locksmith to install new locks for the doors leading to the terrace on both sides of the roof on the fifth floor, and for the doors and windows of the conference room and reading room on the fourth floor. The doors and fire hydrants on each floor will be replaced with new locks.

2. Classify and organize the reading rooms in accordance with the "6S" management standards to eliminate fire safety hazards.

3. Replace and purchase dry powder fire extinguishers as needed, and review the safety status of fire hydrants on each floor after replacing them with new locks.

4. Once again emphasize the requirement that the doors and windows of offices on each floor must be locked after get off work. In response to the safety hazards discovered during the inspection, the inspection team will contact relevant personnel to make timely rectifications to ensure that there are no blind spots in fire safety and no loopholes in anti-theft security, so as to create a stable and safe working and living environment for the company's employees.

Safety production self-inspection report 5

Regarding the requirements of the 20xx safety inspection notice issued by the Construction Office, our company’s self-inspection and self-inspection of safety officers, quality officers and construction team leaders meet the requirements. Leaders at all levels are welcome to visit the construction site to guide the work. In view of the quality and safety issues in construction projects, quality and safety involve a wide range of areas, are highly practical, have many influencing factors, and have high technical requirements. Project quality and safety are the core of project construction and the key to determining the success or failure of project construction. By grasping these two aspects of quality and safety, project construction can proceed smoothly and achieve good social, economic and environmental benefits.

In order to ensure the quality and safety of construction projects, our company adheres to the principles of "quality first" and "safety first" and adopts the "prevention first" approach to conduct dynamic management and emphasize quality and safety control. With "people at the core", we ensure project quality and construction safety, adhere to quality standards, operating specifications, and strictly inspect and accept, so that the final product reaches the best of society. Our company enters the construction stage and adopts the following methods to ensure quality and safety control measures:

1. Quality control measures

1. Quality policy: Adhere to the policy of "a century-old plan, quality first" and establish A sound and complete leadership team.

2. Quality management: all management functions of formulating and implementing quality policies.

In order to achieve the specified quality objectives, organize teams and employees to participate in relevant learning activities and assume corresponding responsibilities.

3. Quality system: implements the organizational structure, responsibilities, procedures, processes and resources of quality management, and strictly controls the on-site acceptance of raw materials and semi-finished products.

4. Quality control: Adopt operational techniques and activities, cooperate with the construction unit, supervision engineers, and quality supervision departments to eliminate the causes of problems at each stage of the quality process, and strictly control "process quality control."

5. Quality assurance: Products or services must meet specified quality requirements to achieve current quality assurance. Verify and audit production, installation, and inspection work. In order to gain the trust of the construction unit, provide necessary information and evidence to relevant departments.

6. Quality objectives: On the premise of ensuring the realization of enterprise quality objectives, the quality system enables the enterprise's operating mechanism to be in the best combination of quality and cost. Only by effectively following the principle of adapting to the environment and achieving the enterprise's objectives , the principle of adapting to the characteristics of construction projects, establish and improve the company's quality system, adapt it to various environments, adapt to various project types and construction characteristics, obtain the best cost, fully achieve corporate goals, and make the company neutral in market competition Stay in an invincible position and gain maximum corporate and social benefits.

2. Safety management technical measures

Safety management at the construction site focuses on the control of unsafe behaviors of people and unsafe conditions of objects. The management purpose is to eliminate all accidents, avoid accident injuries and reduce accident losses.

1. Implement the safety responsibility system and implement responsibility management

(1) Establish and improve the safety production leadership organization headed by the project manager, and carry out safety management activities with organization and leadership.

(2) Establish a safety production responsibility system for personnel at all levels and clarify the safety responsibilities of personnel at all levels. Pay attention to the implementation of the system, pay attention to the implementation of responsibilities, and regularly inspect the implementation of safety responsibilities.

(3) Establish a safety production responsibility system where all employees assume responsibility for safety production. Do it vertically to the end, without missing a link.

(4) All management and operating personnel shall sign safety agreements with the construction project department and make safety guarantee contracts to the project department.

2. Safety education and training

The project department conducts safety education and training regularly and at designated locations to improve safety production knowledge and effectively prevent people from unsafe behaviors.

(1) For all management, operators must have basic conditions and high quality, and hold certificates to work.

(2) All construction and operating personnel must have legal labor procedures. Temporary personnel must sign a labor contract and receive entry education before they can enter the construction site and work positions.

(3) New workers must complete three-level safety education before entering the company, focusing on general safety knowledge, production organization principles, production environment, and production discipline. Emphasize the non-independence of operations. Mainly based on production organization principles, environment, discipline and operating standards.

(4) Mobilize all employees to carry out self-inspection, and combine self-inspection with system inspection to form a situation of self-inspection and self-correction, and inspection and correction at the same time. All employees can be improved in discovering risk factors, educated in eliminating factors, and trained in safety inspections.

3. Civilized Construction

(1) The significance of civilized construction: Civilized construction is an important symbol of modern construction, a basic management work for construction enterprises, and an important part of enterprises. window. Adhering to civilized construction is of great significance.

(2) Measures for civilized construction: The construction site is established with the project manager as the team leader, a sound management individual position responsibility system is established, and the responsibility is divided into pieces according to profession, position, area, and building number, and self-inspection, Mutual inspection and handover inspection system. Achieve self-produced and self-cleaned, daily clean-up every day, clean-up after completion of work, and standard management.

(3) Environmental protection measures: Strengthen the monitoring of dust and noise at the construction site, eliminate dust and sewage pollution, strengthen contact with local environmental protection departments, and contribute to the good environmental benefits of the enterprise.

Safety production self-inspection report 6

In order to further strengthen and improve the safety work of the project department, respond to the call of the institute, effectively protect the life safety and property safety of the majority of employees, and ensure the normal construction of the project Order, combined with the actual situation of the project department, our department conducted a careful and detailed inspection of the safety work at the construction site, and carried out hidden danger inspection and management activities at the construction site. The self-inspection and rectification situation is summarized as follows:

1 , safety management aspects

1. Establishment and improvement of safety organization structure

The project department has established a safety management network and safety production responsibility system and safety management with the project manager as the first responsible person. system. A full-time safety officer is assigned to be responsible for on-site safety inspections and safety inspections at the construction site, forming a top-down safety assurance system.

2. Implementation of safety management system and responsibility system

(1) At present, the project department’s safety regulations are complete and highly operable. Continuously improve the execution of safe and civilized construction systems to strengthen safe and civilized construction management and prevent accidents.

(2) In order to ensure safe production, the project department formulated safety target indicators according to the company’s relevant requirements and decomposed them layer by layer, clarified the safety responsibilities of personnel and departments at all levels, and carried out safety inspections during the construction process. Supervision is implemented in place.

The project department signed a "Safety Responsibility Letter" with the heads of each construction team, and strictly implemented the safety production responsibility system at all levels and the safety accident liability investigation regulations. The quality and safety department of the project department Supervise, inspect and assess the implementation of the system, promptly remind and educate those who violate the responsibility system, and provide rewards and punishments based on assessment results.

3. Safety inspection and hidden danger investigation

In addition to daily safety inspections, the project department also purchases various safety warning signs and construction signs according to the on-site conditions. During construction Corresponding warning placards should be placed at site entrances, passageways, near electrical equipment and other places to remind staff to pay attention to protect themselves and others and eliminate potential safety hazards.

4. Safety education and training

(1) The project department conducts timely safety education and training for new site managers and workers from time to time. The main contents of the training include: corporate rules and regulations, basic safety knowledge, construction safety precautions, various relevant safety technical measures and operating procedures, emergency rescue plan learning, etc.

(2) Participate in safety technical training and certification for electricians, welders, loader drivers and other special operations personnel as required.

(3) Each construction team conducts its own team safety education activities.

2. On-site construction safety conditions

1. Temporary facilities

(1) Temporary facilities are planned in strict accordance with the requirements and the layout is relatively reasonable.

(2) Temporary facilities meet technical requirements such as fire protection, rainproofing, and heat preservation. Personnel are arranged to patrol the living and office areas, construction areas, warehouses, and mechanical equipment parking areas 24 hours a day to ensure the safety of on-site supplies and materials.

2. Safe use of electricity

The construction site ensures "one machine, one gate and one leak" for electrical equipment, ensuring the safety of electricity; warning signs are placed on power supply equipment . Lighting fixtures and power supply lines shall be installed as required. Electricians on duty will conduct regular inspections and deal with hidden dangers in a timely manner to prevent accidents.

3. Special equipment

A dedicated person is responsible for the daily operation, maintenance, shift handover records, etc. of major mechanical equipment. During the use of equipment and transportation vehicles, regular inspections, repairs and maintenance should be carried out, and equipment operation, repair and maintenance records should be filled in. Immediately stop work, rectify or remove equipment with potential safety hazards. Scaffolding construction

4. Fire management

The project department has formulated a fire management responsibility system and implemented it in place. Developed and improved fire emergency plans.

The project department has stepped up inspection and monitoring of fire-prone areas.

(2) There are no violations in work areas or parts where fireworks or smoking are prohibited.

5. Safety protection facilities

During construction, safety management personnel can formally wear and use protective equipment such as safety helmets and safety belts; protective facilities and safety equipment are set up at cave entrances and dangerous locations. Obvious warning signs; fire-fighting facilities are installed near electrical parts and flammable materials.

3. Problems in safety management

1. Individual personnel have weak safety awareness, and habitual violations still occur at the construction site.

2. The layout of construction power lines is chaotic and needs further regulation.

3. Equipment is regularly inspected and various systems are improved; however, the inspection data and records of the equipment themselves are incomplete; further improvements.

4. Some safety protection facilities have not kept up with the progress of project construction, causing safety protection to lag behind during construction.

4. Rectification measures taken:

In order to ensure the safety of project construction and eliminate various safety hazards, the project department proposed the following rectification measures for the main problems existing during the self-inspection process:

1. The project department will strengthen supervision and carry out safety education in batches, using daily inspections, inspections, meetings, safety education and training, bulletin boards, newspapers, documents and other methods to educate employee cadres on safety knowledge, Education and publicity on laws and regulations, etc., to improve employees’ safety awareness and sense of responsibility, and to prevent the occurrence of safety accidents.

2. We will continue to pay attention to the issue of electricity consumption in construction, strictly investigate the illegal use of electricity in workers’ dormitories, and conduct unified and standardized layout of on-site wiring.

3. Strengthen the supervision of habitual violations. To strengthen safety education, management supervision and punishment, we must ideologically improve the safety awareness of employees.

4. Improve and perfect the system to ensure that comprehensive safety management work is well-organized and implemented. Strictly implement the responsibilities of all levels and departments in accordance with the safety responsibility system.

5. Carry out safety inspections and hidden danger inspections and management on a regular basis in accordance with the regulations of the project department in a timely manner, and do a good job in finding and rectifying safety hazards at the construction site.

In short, through this major inspection, some shortcomings and omissions in the safety work of the project department were discovered. The project department made timely rectifications and brought them under effective control, but safety work is a long-term task. The project department will continue to pay close attention to safety, consolidate the basic work of safety management, improve the safety awareness of the majority of employees, enable various tasks and requirements of safety management to be better implemented, further enhance their awareness of safety responsibilities, and clarify their respective responsibilities. Responsibilities to provide safety guarantee for the smooth progress of project construction.