What are the digital instructions of Sony Ericsson mobile phone?

1 and AT+CGMI give the identification of the module manufacturer.

2.AT+CGMM obtains the module identification. This command is used to obtain the supported frequency bands (GSM 900, DCS 1800 or PCS 1900). When the module has multiple frequency bands, the response can be a combination of different frequency bands.

3.AT+CGMR has obtained the modified software version.

4.AT+CGSN obtains the IMEI (International Mobile Equipment Identification) serial number of GSM module.

5.AT+CSCS selects TE function setting. This command reports the status of setting the use of ME TE. ME can then convert each letter entered or displayed. This is used to send, read or write short messages.

6. Set the status of the phone book in +WPCS. This special command reports my usage status through the TE phone book. ME can then convert each input or displayed string letter. This entrance is used to read or write the phone book.

7.CIMI obtains IMSI. This command is used to read or identify the IMSI of the SIM card. You should enter the PIN before reading the IMSI (if a PIN is required).

8.AT+CCID obtains the identification of the SIM card. This command makes the module read the EF-CCID file on the SIM card.

9.AT+GCAP capture capability table. (Supported features)

10, A/ Repeat the last command. Only/command cannot be repeated. This command repeats the previous command.

1 1, AT+CPOF shutdown. This special command stops the GSM software stack and hardware layer. The command of +CFUN=0 has the same function as +CPOF.

12, AT+CFUN to set the telephone function. This command selects the functional level of the mobile station.

13, AT+CPAS returns the active state of the mobile device.

14, AT+CMEE reports mobile device error. This command determines the result code "+cmeerror:

15, AT+CKPD keyboard control. Simulate my keyboard to execute commands.

16, AT+CCLK clock management. This command is used to set or get the current date and time of my actual clock.

17, AT+CALA alarm management. This command is used to set the alarm clock date/tiME in me. (alarm)

18, AT+CRMP ringtone melody plays. This command plays music on the buzzer of the module. There are two kinds of melodies available: incoming voice, data or fax call melody and incoming SMS sound.

19, AT+CRSL sets or gets the volume of the ringing tone.

Second, the call control command

1, ATD dialing command. This command is used to set up a telephone, data or fax call.

2.ATH hang-up command.

3.ATA answers the phone.

4.AT+CEER extended error report. This command gives the reason why the call was interrupted after the last call establishment failed.

5.AT+VTD provides users with the application of sending DTMF (Dual Tone Multifrequency) dual audio through GSM network. This command is used to define the length of dual audio (the default value is 300ms).

6.AT+VTS provides users with the application of sending DTMF dual audio through GSM network. This command allows dual audio transmission.

7.ATDL redialed the last phone number.

8. Automatic dialing (DTR) when the %Dn data terminal is ready.

9.ATS0 automatically answers.

10, AT+CICB calls.

1 1, AT+CSNS single numbering scheme.

12, AT+VGR, AT+VGT gain control. This command is used to adjust the receiving gain of the speaker and the transmitting gain of the microphone.

13, AT+CMUT microphone mute control.

14, AT+ speaker speaker/microphone selection. This special command is used to select speakers and microphones.

15, AT+ echo cancel.

16, AT+ sidetone correction.

17, AT+VIP initializes sound parameters.

18, AT+DUI dial to provide more user information.

19, AT+ huihangup additional user information.

20.AT+RUI receives additional user information.

Third, the network service command

1, AT+CSQ signal quality.

2. Selection of 2.AT+COPS service providers.

3.AT+CREG network registration. Get the registration status of the mobile phone.

4.AT+WOPN reads the name of the operator.

5. list of 5.AT+CPOL priority operators.

Fourth, safety command.

1, AT+CPIN input pin.

2. enter PIN2 at +CPIN2.

3. The number of remaining attempts at the 3.AT+CPINC pin.

4.AT+CLCK device lock

5.AT+CPWD changes the password.

Five, the phone book command

1, AT+CPBS selects phone book memory storage.

2.CPBR reads phone book entries.

3.CPBF looks for entries in the phone book.

4.AT+CPBW writes phone book entries.

5. Telephone inquiry of AT+CPBP phone book.

6, AT+CPBN phone book mobile action. This special command moves the entries in the phone book forward or backward (alphabetically).

7.AT+CNUM signer number.

8.AT+WAIP prevents all phone books from being initialized at the next restart.

9.AT+WDCP deletes the calling phone number.

10, AT+CSVM sets the voice mail number.

Six, SMS command

1, AT+CSMS selects the message service. Supported services include GSM-MO, SMS-MT and SMS-CB.

2.AT+CNMA confirmed the new information.

3.AT+CPMS priority information storage. This command defines the storage area for reading and writing information.

4.CMGF priority information format. The execution formats are text mode and PDU mode.

5.AT+CSAS saves the settings. Save the +CSAS and +CSMP parameters.

6.AT+CRES restore settings.

7.AT+CSDH displays the parameters of text mode.

8.AT+CNMI new information instruction. This command selects how to receive short messages from the network.

9.CMGR reads short messages. Read information from the memory set through the +CPMS command.

10 and AT+CMGL list the stored information.

1 1, AT+CMGS sends information.

12, AT+CMGW writes short messages for storage.

13, AT+CMSS sends information from memory.

14, AT+CSMP sets the parameters of text mode.

15, AT+CMGD deletes SMS. Delete one or more messages.

16, AT+CSCA SMS service center address.

17, AT+CSCB selects the type of information broadcast by the device.

18, AT+WCBM unit broadcast information identification.

19, AT+WMSC information status (whether read, whether sent, etc. ) correction.

20.AT+WMGO information overwrite writing.

2 1 and AT+WUSS do not change the SMS status. Remain unread after executing +CMGR or +CMGL.

VII. Additional Service Orders

1, AT+CCFC call continues.

2. AT+CLCK call is prohibited.

3.AT+CPWD changes the password of the additional service.

4.AT+CCWA call waiting.

5.AT+CLIR call line confirmation limit.

6.AT+CLIP call line confirmation statement.

7.AT+COLP tie line confirmation statement.

8.AT+CAOC expense report.

9.AT+CACM cumulative call metering.

10, AT+CAMM cumulative call metering maximum.

1 1, AT+CPUC unit price and currency table.

Additional services related to 12 and AT+CHLD phones.

13 and AT+CLCC list the current calls.

14, AT+CSSN additional service notice.

15, AT+CUSD unorganized additional service data.

16, AT+CCUG closed user group.

Eight, data command

1, AT+CBST messenger type selection.

2.AT+FCLASS selection mode. This command sets the module to a special mode for data or fax operation.

3.AT+CR service report control. This command allows more detailed service reporting.

4. The result code of at+CRC division. This command allows a more detailed ringtone to be displayed when an incoming call is made.

5.AT+ILRR local DTE-DCE rate report.

6.CRLP wireless communication line protocol parameters.

7.AT+DOPT other radio communication line parameters.

8. Choose data compression in% c.

9. Does AT+DS allow V42 secondary data compression?

Whether 10 and AT+DR report V42 secondary data compression.

1 1, at \ data error correction selection.

Nine, fax command

1, AT+FTM transmission rate.

2.AT+FRM receiving rate

3.AT+FTH uses HDLC protocol to set the fax transmission rate.

4.AT+FRH uses HDLC protocol to set the fax receiving rate.

5.AT+FTS stops transmission and waits for a certain period of time.

6.AT+FRS receives silence.

X. Second Fax Command

1, AT+FDT transmits data.

2.AT+FDR receives data.

3.AT+FET transmits page punctuation.

4.AT+FPTS page transition status parameters.

5. 10: 30, FK ended the meeting.

6.AT+FBOR page conversion byte order.

7.AT+FBUF buffer size report.

8.AT+FCQ controls copy quality inspection.

9.AT+FCR controls the ability to receive faxes.

10, AT+FDIS current meeting parameters.

1 1, AT+FDCC sets DCE function parameters.

12 and AT+FLID define local ID strings.

13, AT+FPHCTO page conversion timeout parameter.

XI。 V24-V25 command

1, AT+IPR determines DTE rate.

2.AT+ICF determines the characteristic structure of DTE-DCE.

3.AT+IFC controls the local traffic of DTE-DCE.

At&T Company. Set the DCD (Data Carrying Detection) signal.

At&T Company. Set DTR (data terminal ready) signal.

6. AT&T Company; S sets DST signal.

7.ATO returns to online mode.

8.ATQ decides whether the mobile phone sends the result code.

9. ATV determines DCE response format.

10 and ATZ are restored to the default settings.

1 1, AT & ampw save the settings.

12。 Automatic test.

13, ATE decides whether to echo the characters.

At&T Company. F return to factory settings.

15。 V setting of display module.

16, ATI requires confirmation information. This command causes the GSM module to send one or more lines of specific information text.

17, AT+WMUX data/command multiplexing.

Twelve, special forces

Description of battery environment for 1 and AT+CCED.

2.AT+CCED automatic RxLev indication.

3. General description of AT+ wind.

4. The data encryption method of AT+ALEA between MSC and me.

5.AT+CRYPT data password mode.

6.AT+EXPKEY key management.

7. at+cPLMN information about plmn.

8.AT+ADC analog-to-digital conversion measurement.

9.AT+CMER mobile device event report. This command determines whether to allow the active sending of the result code when the key is pressed.

10, AT+WLPR reading language preference.

1 1, AT+WLPW writing language preference.

12, AT+WIOR reads the GPIO value.

13, AT+WIOW writes the GPIO value.

14, AT+WIOM input/output management.

15, AT+WAC ignores the command. This special command allows SMS, SS and available PLMN to be ignored.

16, AT+WTONE plays the melody.

17, AT+WDTMF plays DTMF melody.

18, AT+WDWL download mode.

19 and AT+WVR configure the sound rate of the communicator.

20.AT+WDR configuration data rate.

2 1, AT+WHWV display hardware version.

22.AT+WDOP shows the production date of the product.

23.AT+WSVG sound gain selection.

24.AT+WSTR returns the state of the specified state.

25.AT+WSCAN scanning.

26.AT+WRIM sets or returns the bell indication mode.

27. Does AT+W32K allow 32kHz power-off mode?

28.AT+WCDM changes the default melody.

29.AT+WSSW displays the internal software version.

30.AT+WCCS edits or displays the custom attribute setting table.

3 1 and AT+WLCK allow me to personalize on specific carriers.

32.AT+CPHS sets the CPHS command.

33.AT+WBCM battery charging management.

34.AT+WFM feature management. Whether to allow some characteristics of the module, such as bandwidth mode, SIM card voltage, etc.

35. AT+WCFM service characteristic management. Whether Wavecom special functions are allowed.

36.AT+WMIR allows you to create a customized storage image from the currently stored parameter values.

37. Change the default player of melody in +WCDP.

38.AT+WMBN sets different email numbers in the SIM card.

Thirteen, SIM card toolbox command

1, AT+STSF configuration toolbox utility.

2.AT+STIN Toolbox Description.

3.AT+STGI obtains the information of the expected command sent from the SIM card.

4. Results provided by AT+STCR: Toolbox control response.