What are the report words for subject three of the driving license test?

Subject 3 (road test) report words: ?

1. Report to the teacher, xx driving school student XXX has completed the inspection of the car and requests to get on the car. ?

2. After the indoor inspection, the working readings of all components and instruments are normal, and the angles of the left, middle and right rearview mirrors are adjusted appropriately, please start.

Starting requirements: Adjust the seat and fasten the seat belt. Turn on the left turn signal and shift into first gear. Sound the horn. Observe, (right, middle, left, then left) start,

Parking requirements: Observe, turn on the right turn signal, pull over 30 centimeters from the edge of the road, pull the handbrake and engage neutral.

3. Report to the teacher: The operation is completed, please get off the car. ?

Requirements for getting off the bus: first stretch your head to observe and then open the door and get off.

4. Report to the teacher and ask for a summary. (Wait until the teacher concludes: "Thank you, teacher")

Basic test items for subject three: preparation for getting on the bus, starting, driving straight, changing lanes, passing intersections, pulling over, passing crosswalks, passing school zones, Passing the bus station, meeting, overtaking, turning around, driving at night;

Before getting on the bus: (go around, look, drive). "Go around" means to go around the car once, "look" means to look behind the car after going around the car and before opening the door to make sure there are no cars coming from behind to ensure safety; "open" means to open the door and get on the car.

Start off

Turn on the light, put the handbrake in gear, release the handbrake, look in the mirror, turn your head, accelerate, turn the body upright, turn the steering wheel, kick the accelerator, and put the second gear in. Explain: "Turn on the light" means turning left. "Looking at the mirror" refers to the inner and outer rearview mirror, then turn your head to look to the left and rear, then slowly lift the clutch, turn off the turn signal when the car body is turning, and shift the oil into second gear.

(1) Before starting the engine, candidates should close the door, adjust the driver's seat, rearview mirror, check the instruments, fasten the seat belt, and report: "Ready" after starting the engine. After the examiner determines that it is safe, he should issue instructions to the candidates: Start.

(2) After the examiner approves, step on the clutch, shift into first gear, turn on the left light, honk the horn, look at the left mirror, release the handbrake and drive. If there is a car behind you, you can go straight for a while and then merge. If there is no car, turn left and merge, then go straight. When starting, do "one step on the clutch, two on the gear, three on the steering wheel, four on the horn, five on the rear mirror, six on the brake, slowly lift the clutch, light on the gas; shift to second gear and turn off the steering."

Driving in a straight line:

When driving in a straight line, candidates must ensure a safe speed and safe distance from the vehicle, understand the driving speed of the vehicle, pay attention to the road conditions, and take corresponding measures. There should be no swinging left or right or unstable direction.

Change lanes:

Observe and judge the traffic flow conditions behind the vehicle, to the sides and in the lane to be changed, and after confirming that a safe distance is maintained from other vehicles, turn on the turn indicator. . 1) Before changing lanes, observe the traffic conditions behind you through the interior and exterior rearview mirrors. 2) Use the turn signal correctly and turn the steering wheel after turning on the turn signal for 3 seconds. 3) When changing lanes, the safe distance between vehicles should be correctly judged, the driving speed should be controlled, and the normal driving of other vehicles should not be hindered. 4) When changing lanes, it is not allowed to continuously change more than two lanes, long-term riding lane dividing lines, riding lane center solid lines or lane edge solid lines.

Passing through intersections:

When passing through intersections, candidates must slow down, sound the horn, and make obvious sideways movements of looking left and right to accurately observe the surrounding situation.

Passing the crosswalk, passing the school area, passing the bus station:

When receiving the three instructions, candidates must slow down, sound the horn, and look left and right. When encountering a pedestrian crossing a crosswalk, you should stop and give way. Candidates must strictly implement the principles of safe driving, ensure even distribution of attention and reasonable shift of sight.

Meeting cars:

When vehicles are driving on a road with no center separation or center line to meet cars, the examiner issues the "Meeting cars" instruction, and candidates should strictly abide by traffic safety laws. Follow the laws and regulations to ensure civilized driving and courtesy. During the meeting, keep a safe distance laterally.

Overtaking:

After hearing the "overtaking" command, candidates must observe the traffic conditions behind and on the left through the interior and exterior rearview mirrors, and accurately choose the timing of overtaking and the safety of the overtaking and overtaken vehicles. distance to ensure safe overtaking. (Note: In the actual test, there is no car to overtake. Just like changing lanes, just remember to turn on the lights.) During the overtaking process, you must reasonably shift your sight, comply with regulations, and drive safely, etc.

U-turn:

After hearing the "U-turn" instruction, candidates must accurately choose the timing and location of the U-turn based on the principle of safe driving. During the U-turn, candidates must not interfere with other vehicles driving normally. Vehicle and pedestrian traffic.

When you see a U-turn sign, remember to turn on the left turn signal (the rule is to turn on the light within 100 meters to 50 meters, it is better to turn on the signal sooner rather than later). Slow down and downshift to second gear before approaching the U-turn point. Pay attention to the left mirror to observe the traffic conditions behind you. Also pay attention to the traffic conditions on the other side. Be careful not to rush. If the lane is narrow, you can hit it right and then hit it left, so that you don't You will hit the edge of the road, turn around and go back to the right direction.

Pull over:

Step 1: When you hear the command "Pull over", first determine the location of the pull over, then turn on the right turn signal and turn to the right Steering wheel, angle is 90 degrees.

Step 2: When the center of the front of the car coincides with the curb, quickly turn the steering wheel to the left. The angle is greater than 180 degrees.

Step 3: When the front 1/3 of the car coincides with the curb, return the steering wheel to the straight position. If the car deviates at this time, always keep the front 1/3 of the car and make slight adjustments to the car.

Step 4: When the vehicle body is parallel to the curb, stop 10 to 30 cm away from the curb.

Conclusion: After selecting a parking space, be sure to turn on the right turn signal first. Points will be deducted for not lighting up.

Driving at night:

When assessing night driving, the main assessment is whether the candidate can comply with the provisions of the Road Traffic Safety Law and Implementing Regulations, and whether the lights and lights can be turned on correctly during night driving. Use lights.