How to set up Great Wall Broadband?

Question 1: How to set up the Great Wall Broadband Internet access? Just use the dial-up connection that comes with XP to enter the account password.

If the system does not have a dial-up icon, create one yourself. Very simple

Question 2: How to set up wifi for Great Wall Broadband? Debug the router directly and enter the account password. Debugging method: Plug the wired broadband network cable into the WAN port of the wireless router, and then use a network cable to connect directly from the LAN port to your laptop (or desktop). Then open the browser and enter 192.168.1.1 or 192.168.0.1 (see your manual). Enter the management account and password, which is usually admin. Enter the setup wizard and fill it in step by step. Select PPPOE as the dialing method. Then fill in the username and password. For data and wireless network security, you go to the special wireless column to activate the key. Generally, choose WEP mode and fill in the key you want to set. Pay attention to the number of digits in the key and read the prompts on your page, and then Select the route to restart in the router, instead of manually cutting off the power, then it will be fine. The mobile phone and computer will find the routing signal. Enter your preset password and you can access the Internet

Question 3: Mobile Great Wall Broadband Wireless Router How to set up the router:

1. Enter the management address - enter 192.168.1.1 or tplogin in the address bar of the browser (the new TP router has a management address marked on the label on the back of the router);

2. Set a management password - you need to set a management password for the router, and then use this password to log in to the interface.

Start the setup wizard and select PPPoE dial-up (ie, broadband dial-up Internet access);

3. Enter the broadband account password. Enter the broadband account password provided by the operator (broadband service provider). Be sure to enter it correctly and it is case-sensitive and special characters;

4. Set up the wireless signal - Set the wireless signal name (SSID) and wireless password (PSK password) respectively. Please do not set Chinese or special characters;

5. The setting is completed - some routers prompt to restart the router, just click Restart. At this point, The router is set up.

Note: After the setting is completed, the mobile phone can access the Internet normally. If other terminals need to access the Internet, the wired computer uses a network cable to connect to any LAN port of the router

and the wireless terminal searches for a signal connection. That’s it, no other settings are needed:

Question 4: How to change the network password of Great Wall Broadband? Go to the computer, click Network Management, Network Password, Modify,

Question 5: What is used at home? Great Wall Broadband, how to set up the wireless network? You also need to enter the router settings, select PPPOE as the network access type, and fill in the broadband account password.

External network plug the network cable into the WAN port of the router, then plug one end of the network cable into the LAN port and the other end into the computer.

Question 6: How to set Great Wall Broadband to automatically connect to the broadband when it is turned on? First right-click on Network Neighborhood → Properties, then right-click on Broadband Connection, Properties 2 Options → Uncheck the second and third dial-up options.

Just drag the networking icon to the start, program, and start it.

This is what I do in my house!

Question 7: Great Wall Broadband router setting problem Great Wall Broadband is generally a network cable that enters the home. If you use an all-in-one machine as a router, it will be more troublesome.

You need to connect the broadband network cable to the lan4 port, connect the computer to other lan ports, and then enter 192.168.1.1

In the network parameters--Ethernet access settings, check to enable LAN Access

Next, select the access type as pppoe, fill in the long and wide account and password, and check the automatic connection option

After saving and restarting, see if you can access the Internet normally.

If the connection is wired, it will be connected wirelessly. Set the wireless parameters yourself.

It is best to reset the 89741n before setting it up

Question 8: How to set up the router after re-opening an account with Great Wall Broadband. The router setting methods are generally similar, and the main thing is to follow the prompts. You can refer to the following method to set up

The setting method for the wireless router is as follows:

1. Connect the broadband bus (the network cable from the modem) to the WAN port of the router.

2. Connect one end of the network cable to any LAN port of the router, and the other end to the computer, start the computer and router device;

3. After starting the device, open the browser and enter in the address bar 192.168.1.1 Enter the wireless router setting interface.

4. An account and password for logging into the router will appear on the setting interface. Enter the default account and password admin

5. Follow the step-by-step setting wizard and select the Internet access method. Usually ADSL users Select the first item PPPoE. If you are using other network service providers, select the following two items according to the actual situation. If you don’t know how to choose, just select the first item to automatically select it, which is convenient for novices to operate. After selecting, click Next One step;

6. Enter the account number and password applied for from the network service provider, and go to the next step after completing the input;

7. Set the wifi password, try to make the alphanumeric combination as complex as possible It’s not easy to get caught online.

8. After the input is correct, you will be prompted whether to restart the router. Select Yes to confirm to restart the router. After restarting the router, you can access the Internet normally.

Question 9: How to set up the Great Wall Broadband Fiber Router Router installation steps:

1. Change the local connection to automatically obtain an IP address.

2. Connect the broadband network cable to the "WAN" port on the router, and any one of the router's ports (1, 2, 3, 4) to the network cable port on the back of the computer host.

3. Open the browser and enter 192.168.1.1 or 192.168.0.1. The router’s password is admin

4. Enter the router settings screen, select PPPOE (ADSL virtual dial-up) mode, and enter yourself Home account and password, confirmed.

5. Then set the SSID, encryption method and password.

6. Save and restart. The router is set up.

Question 10: How to set up a broadband connection (Great Wall Broadband) in win7? The two computers are WIN7 systems. Great Wall Broadband does not have a MODEM to connect to the home, and only has one network cable. It requires pppoe to set up. My Tietong network cable is also directly connected to the home, and does not require a modem. However, I can use the PPP dial-up method of the router