How to set up a wireless gsm security alarm to make a phone call?

If you use Kelixin KS-899, simply program the following KS-899 series to enter the programming: Automatic login function: When using the GSM alarm module for the first time, the GSM alarm module will be powered on and initialized, that is, after the host GSM light is on, turn on the automatic login function within 30 minutes, dial the phone number of the SIM card installed on the module, and hang up after hearing the phone ring for more than 3 times. After that, the GSM alarm module will confirm this operation by replying to the power-on SMS, and this phone will be registered as the first programmed phone number, which will be used as the phone number for Chinese SMS and alarm by default. At this time, the GSM alarm module can simply set the alarm operation function and set the instruction format of programming telephone number: programming telephone number 1: deleting programming telephone number x: deleting programming telephone number x (Note: x is any number between 1 ~ 3, representing 1 ~ 3 groups of programming telephone numbers. Set the command format of alarm telephone number: alarm telephone number x: t and specific telephone number (Note: X is any number between 1 ~ 8, representing 1 ~ 8 groups of alarm telephone numbers, and each group of telephone numbers has at most 20 digits. T is the type code of the alarm telephone number, and its definition is shown in the following table. Each group of telephone numbers (including a *) can be up to 20 digits long. ) Digital phone type Note 0: This group of phones is disabled 2. Call the police number 3. The "*" symbol 4 cannot be entered in the SMS alarm phone. Contact ID alarm center 5. Instruction format for deleting alarm X telephone number for regular communication telephone: delete alarm X (Note: X is any number between 1 ~ 8, representing 1 ~ 8 alarm telephone numbers. Description: Delete the X alarm phone number in the alarm phone list. Instruction format for setting alarm mode: Alarm mode: [SMS] [Dial] [Dial first and then SMS] [SMS first and then dial] Instruction description: Alarm mode refers to the working mode used by GSM alarm module to inform users of alarm situation when it occurs. Users can set one of the following four ways: SMS: GSM alarm module only sends SMS alarm to users in the phone list of SMS alarm users, and does not make calls. Dialing: GSM alarm module only calls users in the dial-up alarm user phone list, and does not send SMS alarm. Dial first, then SMS: GSM alarm module will send SMS alarm to users in SMS alarm user phone list first, and then call users in dial alarm user phone list. SMS first, then dial: GSM alarm module will call users in the dial-up alarm user phone list first, and then send SMS alarm to users in the SMS alarm user phone list. Command format for enabling/disabling sending startup Chinese short messages: startup short messages: Description of the command: When startup Chinese short messages are enabled, the GSM alarm module will send startup Chinese short messages to the set phone number every time it is turned on. If the time and date of GSM alarm module are not automatically calibrated, a Chinese short message with calibration time will be automatically added. Default value: Enable/disable sending information Chinese SMS instruction format: SMS: enable/disable instruction description: When you enable SMS in Chinese, the GSM alarm module will send an information Chinese SMS to each set SMS alarm phone number every time an alarm occurs, such as AC power failure, low battery power, low battery power recovery, anti-disassembly/loss recovery, etc. Default value: it is forbidden to set the number of circular dialing. Instruction format: number of circular dialing times: XX Instruction Description: XX is the number of circular dialing times to be set, which can be selected from 03 to 15 times, and must be two digits; When the GSM alarm module makes alarm dialing, it will call from the first dialing type to the last dialing type. When the GSM alarm module reaches the number of times you set, the GSM alarm module will stop dialing immediately. Default value: 03 Set the command format of sector name: sector [X]X name: X is less than 12 Chinese sector names (Note: x is any number between 1 and 16, representing 1 to 16 sectors. Note: Each sector can be assigned a name separately, and the name of sector X can be set as the name of the detector or sensor, or as the site name of the sector. Note 1: If a zone name is set, an alert message will be sent to the user using the zone name instead of the zone number. Note 2: If you don't enter specific sector name characters, just enter "Sector X Name:", the original setting name will be deleted, and the sector number will be used instead of the sector name when giving an alarm. Instruction format of factory reset value: factory reset: DDDDDD (Note: DDDDDD stands for remote programming password, which is fixed as 6 digits, and "d" is any number between 0 and 9. Instruction Description: Restoring factory set values refers to restoring the user set values of all the above programming operation instructions to factory set values. When the entered remote programming password is correct, the GSM alarm module will perform the operation of restoring the factory setting value. After the operation is completed, the GSM alarm module will delay 10 second, and then the system will restart.