Telecom error code daquan

China Telecom Error Code Encyclopedia and Its Meaning Error 602 Port has been opened: Dial-up network cannot be connected due to incorrect installation or use of equipment.

Reason: RasPPPoE is not completely installed correctly. Solution: Uninstall any PPPoE software and then reinstall it.

Error 605 Port information cannot be set. Problem: Dial-up network can't set the use port due to equipment installation error. Cause: RasPPPoE installation is incomplete. Correct solution: uninstall any PPPoE software and reinstall it.

Error 606 port is not connected. Problem: Dial-up network can't connect the required device port. Reason: RasPPPoE installation is incomplete and correct, cable failure, ADSL modem failure. Solution: Uninstall any PPPoE software, reinstall it, and check the network cable and ADSL modem.

Error 608 There is no problem with the device: The dial-up network connected device does not exist. Cause: RasPPPoE is not completely installed correctly. Solution: Uninstall any PPPoE software and reinstall it.

Error 609 There is no problem with the device type: the device type connected to the dial-up network cannot be determined. Cause: RasPPPoE is not completely installed correctly. Solution: Uninstall any PPPoE software and then reinstall it.

Error 6 1 1 The route is not available.

6 12 Route Unassigned Problem: Incorrect routing of dial-up network connection Reason: RasPPPoE installation is incomplete and correct. Solution to ISP server failure: uninstall any PPPoE software, reinstall it, and call ISP to ask.

Error 6 17 port or device has been disconnected.

Problem: The device connected to the dial-up network has been disconnected. Reason: RasPPPoE is not completely installed correctly, the ISP server is out of order, and the connecting cable and ADSL modem are out of order. Solution: uninstall any PPPoE software, reinstall it, call ISP to ask, and check the network cable and ADSL modem for errors.

6 19 problem: unable to establish connection with ISP server. Cause: ADSL ISP server failure, ADSL telephone line failure. Solution: Check whether ADSL signal lamps can be synchronized correctly. Call the ISP to ask

Error 62 1 Unable to open phone book file.

Error 622 Unable to load phone book file.

Error 623 Phone book entry not found.

Error 624 Unable to write phone book file.

Error 625 Invalid information found in the phone book.

Problem: Windows NT or Windows 2000 Server network RAS network component failure Cause: Uninstall all PPPoE software and reinstall RAS network component and RasPPPoE.

The modem was disconnected due to hardware failure. The link was disconnected for one of the following reasons: 1, and an unrecoverable error occurred in the modem (or other communication device). 2. There is an unrecoverable error in the communication port. 3. The modem cable is not plugged in. To diagnose and correct the problem, do the following: 1. Make sure the modem is turned on and the cable connection is reliable. 2. In order to ensure the normal operation of the modem, the command test can be conducted through the control panel.

63 1 The user disconnected the modem. An operation on the computer disconnected. Redial.

632 Incorrect structural dimensions have been detected. An internal error occurred. Restart the computer to ensure that all recent configuration changes take effect. If the error persists, please refer to the Windows 2000 error log for detailed warnings or errors.

The 633 modem is in use or not configured to dial out. If it is a dial-up network connection, the com port that the network connection is trying to use is being used by other active network connections or other processes (for example, a telephone line monitoring program such as a fax program). Quit the application that blocked the use of com port. If it is a virtual private network (VPN), you will not be able to open the VPN device that the network connection is trying to use. If the problem persists, please consult your system administrator.

Your computer cannot be registered on the remote network. The remote access server cannot register your computer name on the network, which usually appears in NetBIOS protocol, but it may also appear in tcp/ip or ipx. Typically, this error occurs when the address is already in use on the network. Please contact the system administrator.

An unknown error occurred in 635. An internal error occurred. Restart the computer to ensure that all recent configuration changes take effect. If the error persists, please refer to the Windows 2000 error log for detailed warnings or errors.

The device connected to the port is not the expected device. The hardware configuration and configuration settings used for the connection may be contradictory. If you change the communication device (such as serial port or modem), please reconfigure the dial-up connection.

637 A string that cannot be converted was detected. An internal error occurred. Restart the computer to ensure that all recent configuration changes will take effect.

The request timed out. An internal error occurred. Restart the computer to ensure that all recent configuration changes will take effect.

639 asynchronous network is not available. NetBIOS network configuration may be incorrect. Restart the computer to ensure that all recent configuration changes will take effect.

A NetBIOS-related error occurred in 640. The modem could not negotiate the connection at the set speed. Set the initial speed of the modem to a lower value, and then redial. You can also try to disable modem compression and software compression. If the connection cannot be established, try adding ipx/spx and NetBIOS protocols to the connection.

64 1 The server could not allocate NetBIOS resources needed to support the client. Ask the system administrator to increase the resource capacity of remote access server or stop some unimportant services, such as messenger service and network DDE.

The NetBIOS name of the 642 computer has been registered on the remote network. Another computer with the same name has logged into the remote network, and each computer in the network must be registered with a unique name to verify the following items: 1. The computer with the same name as yours is not in the network you are connecting to. 2. The computer is not physically connected to the network you are trying to connect to.

The network card on the server side is out of order. Please report this error to the system administrator.

You will not be able to receive network pop-up messages. Another computer connected to the network is using your computer name, and the mail sent to you will be sent to that computer. If you want to receive information from a remote workstation, you must remember to log off the office computer before dialing into the network next time. This error does not affect messages sent by outlook, outlook express and exchange.

645 An internal validation error occurred. An internal error occurred. Restart the computer to ensure that all recent configuration changes will take effect.

This account is currently not allowed to log in. Configure an account to restrict access to this network. If you need to access the network at different times of the day (instead of the currently configured time), ask the system administrator to change the settings.

This account has been disabled. The user account is disabled. This may be due to multiple failed login attempts, or because the system administrator has disabled the account for security reasons. Ask the system administrator to enable this account in local users and groups.

The password for this account has expired. If you connect through a network and dial-up connection, you will be prompted to change your password. If you use rasdial connection, you can change the password by 1, press Ctrl+Alt+Del 2, click "Change Password", and then follow the prompts. If you are a system administrator, but your password has expired, you can't change it yourself, only another administrator can change it.

Account number 649 has no permission to dial in. This account does not have dial-in permission for the following reasons: There is a valid account in the selected domain, but the account does not have access to the remote network. Ask your system administrator to enable dial-in permissions for user accounts, or enable dial-in permissions in routing and remote access. The account has expired, been disabled, locked or the dial-in access is locked. You tried to connect outside the allowed server login time limit, or you tried to connect outside the allowed dial-in access time limit, or the policy applied to the account may not allow dial-in access. The caller's ID rules may prevent the connection, for example, you need to dial an account from a specified number. The remote computer may only allow local accounts to connect. An authentication protocol is required, and the computer cannot negotiate it, or the computer tries to use a protocol that has not been verified by the policy on the remote computer. If you have an account with dial-in permission in another domain, please do the following to use the account in that domain. 1. Right-click the connection, and then click Properties. 2. On the Options tab, select Prompt for Name, Password, Certificate, etc. And the Windows login domain check box. 3. In the Security Measures tab, clear the Automatically use my Windows login name and password (and domain, if any) check box, and then click OK. 4. Double-click the connection, and then click Dial. 5. Specify the appropriate user name, password and domain.

The 650 remote access server is not responding. This error may be caused by any of the following conditions: 1. The remote access server is not running. Please contact the system administrator to ensure that the server is running. 2. The line noise is too loud, or the modem cannot negotiate correctly with the modem of the remote access server at the selected speed. In any case, you should reduce the initial speed (bps) of the modem and redial. 3. Check the hardware compatibility list to ensure that your modem is listed. 4. It may be necessary to replace the serial cable of the modem. 5. The authentication settings used to connect may be incorrect. Please contact your system administrator to ensure that your authentication settings meet the requirements of the remote access server. 6. Software compression of remote access server and hardware compression of modem can be enabled at the same time. Generally, remote server software compression is enabled and hardware compression is disabled.

The 65 1 modem reported an error. The modem (or other device) reported an error. If you have a dial-up connection and use a supported external modem, turn off and restart the modem. Close and restart the network and dial-up connection, and then redial. If your modem is not supported by your network and dial-up connection, switch to a supported modem. Please ensure that the modem for remote access is configured correctly. If it is a virtual private network (VPN) connection, an incorrect TCP/IP address may be specified in the connection configuration, or the server you are trying to connect to is unavailable. To determine whether the server is available, please consult your system administrator.

652 has an unrecognized response from the modem. The message returned by the modem (or other device) is not listed in one or more script files (Pad.inf, Switch.inf or filename.scp). If you use a supported external modem, turn off and restart the modem, and then redial. If the problem persists, try connecting at a lower initial speed.

The macro required by the modem could not be found in the 653 device. INF file section. A command or response in a device. The INF file partially refers to an undefined macro. No macros were found in the device. INF file section.

Macros in the device. The INF file section contains undefined macros. 657 Unable to open the device. INF file. The device name in the device. INF or media. The INI file is too long. 659 media. The INI file refers to an unknown device name.

660 equipment. The INF file does not contain a response to the command. 66 1 equipment. The INF file is missing a command. An attempt was made to set a macro that is not listed in the device. INF file section. 663 media. The INI file refers to an unknown device type.

The system cannot read the media. INI file. Usage parameters in 669 media. The INI file is invalid. The 670 system cannot read some names from the media. INI file. 67 1 The system cannot read the device type from the media. INI file. The system cannot read the device name from the media. INI file. The system cannot read the usage from the media. INI file. The 674 system cannot read the maximum connection rate (bps) from the media. INI file. The 675 system cannot read the maximum operator connection speed from the media. INI file. The 68 1 modem reported a general error. A configuration file for network and dial-up connections may contain invalid information. If your modem is not supported by the network and dial-up connection, you should switch to a supported modem.

The system is out of memory. The system is out of memory. Close some applications and redial.

The modem is not configured correctly. If another connection is using the device, it should be disconnected. Modify the connection to use other devices.

The 666 modem is not working properly. The modem (or other device) did not respond for the following reasons: 1. The external modem is turned off. 2. The modem is not firmly connected to the computer. Make sure that the cable is securely attached to the modem and computer. 3. The serial cable does not meet the requirements of "Network and Dial-up Connection". 4. The modem has hardware problems. Turn off the modem and restart it after 20 seconds.

The 668 connection was terminated. Redial the connection. If you continue to receive this message, you should slow down the initial speed of the modem and turn off the advanced features of the modem. If you dial manually, you should make sure that you are connected before clicking Finish. If Operator-Assisted Dialing is selected in the Advanced menu of the Network and Dial-Up Connections folder, it is a manual dial. Telephone line 676 is busy. Redial the number. Implement automatic redial in the Options tab of the connection properties. If it is a virtual private network (VPN) connection, please check the host name or IP address of the target server and try to connect again. Also contact the system administrator to verify that the remote server is running.

677 was answered by a person, not a modem. The modem or other device is not off-hook. Check the number and dial again. If it is a virtual private network (VPN) connection, please check the host name or IP address of the target server and try to connect again.

678 didn't answer. The modem or other device is not off-hook. Check the number and dial again. If it is a virtual private network (VPN) connection, please check the host name or IP address of the target server and try to connect again. Also make sure that the phone line is plugged into the correct slot of the modem.

The carrier cannot be detected by the 679 system. The modem or other device is not off-hook. Many modems will return this error if the remote modem is not off-hook. Check the number and dial again. If it is a virtual private network (VPN) connection, please check the host name or IP address of the target server and try to connect again. In the "Options" card of connection properties, automatic redialing can be realized.

680 has no dial tone. The telephone line may not be properly connected to or disconnected from the modem. The phone number needs a prefix, such as 9, to dial an outside line, or the number is too long. Make sure that the telephone line is plugged into the correct slot of the modem. Also make sure that all special access numbers connected to the outside line are added, such as prefix 9 followed by a comma. For example: 9555-0 100. Check the telephone line for intermittent sounds, which means there is voice mail. Many modems cannot dial more than 34 digits. When a long number is encountered, these modems divide it into two or more strings and dial only the first string (incomplete). This happens in robots and multi-technology demodulators. The only known way to solve this problem is to use another brand of modem.

69 1 Access is denied because the user name and/or password are invalid on this domain. The user account is not registered in the listed domain, the password has expired, or the information entered is incorrect. If no domain is specified, the remote access server will try to verify the user name and password in the domain to which it belongs. Please re-enter the user name, password and domain carefully. If you are not sure about this information, please consult your system administrator.

The 692 modem has a hardware failure. The modem (or other device) is not responding for the following reasons: the modem is turned off, has a fault, or is not reliably connected to the computer. To solve this problem, do the following: 1) Reset the modem. Refer to the hardware documentation for details. 2) If you use an external modem, please make sure that you use an appropriate serial cable and the cable connection is reliable. You may want to try replacing the modem cable. Similarly, if you use an adapter to connect an external modem to a serial port, make sure that the adapter is wired correctly so that the modem can communicate. For example, the mouse's 9-pin to 25-pin adapter does not work properly in a serial network connection. 3) Test the serial port or multi-port adapter and replace it if necessary. 4) Make sure that the handshake option of the modem is configured correctly. Consult your hardware documentation for information about the different handshake options available to your modem. 5) If your modem is not supported by the network and dial-up connection, please switch to a supported modem. 6) Verify that other applications (for example, "HyperTerminal") are not using the communication port. If you are using this port, starting a network and dial-up connection may cause this message to appear.

The machine is not started.

The 696 state machine has been started.

The response loop did not complete.

The response of the 699 modem caused a buffer overflow. An internal error occurred. Restart the computer to ensure that all recent configuration changes will take effect.

Extended commands in 700 devices. INF file is too long. The command in the script file cannot exceed 256 characters. The command is decomposed into multiple commands.

COM driver does not support the connection speed used by 70 1 modem. The modem tried to connect at a speed that the serial port could not explain. Please reset the initial speed to the next lowest standard bps speed.

The 703 connection requires user information, but the application does not allow user interaction. The server you are trying to connect to requires user interaction. Rasdial commands, or applications used to try dialing, do not support user interaction. If possible, try to connect using an existing connection in the Network and Dial-up Connections folder. If you use a scripted connection, try using a dial-up connection with the Terminal feature configured. The terminal window can realize the required user interaction.

The 704 callback number is invalid. The callback number specified for customer is invalid.

The 705 authentication status is invalid. An internal error occurred. Restart the computer to ensure that all recent configuration changes will take effect. If the error persists, please refer to the Windows 2000 event log for detailed warnings or errors.

707 has an error related to the X.25 protocol. The X.25 connection returned an error. Ask the X.25 provider to explain the diagnostic information given.

708 account expires. Ask your system administrator to reactivate your account. Error changing the password on the domain. The password may be too short or the same as the previous password. Please try to change the password again. If you continue to receive this message, please report it to your system administrator.

7 10 detected a sequence overflow error when communicating with the modem. You should slow down the initial speed of the modem (bits per second) and redial.

7 1 1 Remote Access Service Manager failed to start. Additional information is provided in the event log. The Remote Access Connection Manager service may not be running. Modify the service to start automatically. Restart the computer to ensure that all recent configuration changes will take effect. If the error persists, please refer to the Windows 2000 event log for detailed warnings or errors. For more information, please visit the Personal Support Center (/) on the Microsoft website. There may be a problem with the modem or the modem cable. Try replacing the modem cable.

7 12 dual port is initializing. Wait a few seconds before redialing. This error occurred on a connection configured to receive calls (duplex connection). This error may also occur when the server dials out while initializing the connection to receive the call. Network and dial-up connections will be redialed in a few seconds.

7 13 has no active ISDN line available. Please make sure that the ISDN cable is inserted correctly and the terminal resistor is installed correctly (refer to the documentation of the ISDN card), and then redial. If you still receive this error, please contact the customer service of ISDN provider or ISDN telephone company.

7 14 has no ISDN channel to dial. All available ISDN channels are busy. Generally speaking, ISDN provided at BRI ("Basic Rate Interface") service level provides two channels through which voice or data calls can be made. If both channels are in use, the network and dial-up connection cannot be dialed out. Hang up a channel and redial.

7 15 There are too many errors due to the poor quality of the telephone line. During authentication, there were too many asynchronous errors on the telephone line. Try again. If the problem persists, you should lower the baud rate and disable all functions of setting up the modem.

7 16 remote access service IP configuration is not available. There is a problem with the TCP/IP configuration on the remote access server. For example, the connection is requesting an unavailable TCP/IP address from the server. Please contact the system administrator to verify the TCP/IP settings of the server.

7 17 There is no IP address available in the static pool of IP addresses of the remote access service. Try to use an IP address that will not cause remote network conflicts. If possible, use DHCP to avoid address conflicts.

7 18 The connection waiting for a valid response from the remote computer timed out. The PPP session was started, but it was interrupted because the remote computer didn't respond within an appropriate time. This may be due to poor line quality or problems with the server.

The 7 19 connection was terminated by the remote computer. The PPP session started, but was interrupted at the request of the remote computer. There may be an error in the server. The connection attempt failed because the PPP control protocol between your computer and the remote computer is inconsistent. PPP network control protocol is not configured for this connection or the corresponding network protocol is not installed. This error may occur when the network protocol type changes during the product upgrade.