What should I pay attention to when renovating a new house and only changing the kitchen, bathroom and water and electricity?

The renovation of the new house only changes the water and electricity in the kitchen and bathroom. That's it!

However, I suggest that you simply change the living room and bedroom and move some unreasonable positions. It is best to control the living room and the bedroom, which is relatively convenient to use in this later period.

Let's talk about kitchen and bathroom first!

kitchen

The waterway in the kitchen is relatively simple, as long as the materials are used well and the pipes are hot-melted. The only high waterway is the pipeline of gas water heater, and the height I usually reserve is about 1 m2.

Waterway switch is reserved in the kitchen. Everything else is in the cupboard. The faucet in the sink is reserved with hot and cold water, the height is about 35-40, and no water is used in other places.

There are many circuits, so be sure to pay attention to the location of the socket.

Let's start with what's in the cupboard

If it is an integrated stove, it is necessary to reserve a socket in advance, calculate the position of the integrated stove, and change a socket next to it, the height is about 35-40.

The water purifier should also reserve a socket, generally under the sink, at the same height.

Dishwasher, this is next to the sink. You should also calculate the position in advance and reserve a socket beside it.

Above the cupboard

Cabinets are generally divided into washing, cutting and frying, operation desk and water heater, which are basically reserved sockets.

Let's talk about the range hood first and the check valve. Many communities are reserved, but the ground floor is relatively high. Before sticking bricks, the bricks must be moved up and placed on the ceiling. The pipes of the later range hoods are sealed at the top, which looks good.

Generally, range hoods or integrated stoves are 900 wide, and the reserved height of range hoods is generally 1.8 meters high.

Console, many consoles are under the window, so the position of this reserved socket should be calculated carefully. Bricks are generally 5 cm, and floor heating is 8- 10 cm high. The cabinet is generally 80 cm high, and the water stop is generally 4 cm high. The socket should be at least higher than the water stop.

The sockets reserved here are all bottom boxes of 1 18, and the upper edge is just under the window. If you stick bricks, it will be about 3 cm. This is very practical.

The socket of the water heater is reserved next to the water pipe.

The height of the socket shown below is miscalculated, which is inconvenient and dangerous to use later.

Bathroom waterway circuit

Let's talk about waterways (public toilets)

The bathroom is equipped with an independent waterway switch. Generally, the waterway is divided into several areas, including washbasin, washing machine, mop basin, floor drain and shower.

The washbasin needs hot and cold water, which is usually left cold and right hot, and the height is about 35-40.

Washing machine, mop pool, etc. See if the bathroom is the right size. If the space is suitable, you can make a reservation. The washing machine is a cold water pipe I usually reserve a height of 1㎡, install a special faucet for washing machine, and drain water at any time.

Shower showers also need hot and cold water, the height is generally 1 m 1, and the distance between hot and cold water pipes is generally 15 cm. Be careful not to tilt the tiles, otherwise it will be difficult to install the shower in the later stage.

Toilet circuit

There is more water here, but generally there are fewer reserved circuits. There are about five holes next to the washbasin for the hair dryer, five holes for the smart toilet, and the main light and switch. Yuba, switch.

As long as the positions of the five holes of the hair dryer do not get in the way, the height is generally the same as that of the switch, about 1350. There are also high points that can be changed.

Under the smart toilet, be sure to reserve the toilet next to it, not behind the toilet tank. It is not good to install the toilet in the later stage, and the height is generally 350-400.

Yuba, in order to change the circuit in advance, generally five wires are reserved, mostly 1.5, and the switch is placed in a suitable position, and the height is generally around 1350.

I can't remember anything else for the time being.

However, it is still recommended to install that dual control in the living room and bedroom. It's really convenient to use in the future, so just change it. Some unreasonable moves will do, and it won't cost a few dollars, but it's more convenient to use.