Joke Collection Website - Mood Talk - How to drive auto start Jr

How to drive auto start Jr

Automatically start Jr:

A, the preparation work before start-up.

Carefully check the situation around the vehicle and pay attention to whether there are obstacles under and around the vehicle body. The engine needs to be warmed up when the cold car starts, and the warm-up time depends on the temperature. Generally, it is required to restart after the idle speed returns to normal. Be sure to fasten your seat belt and see if the driver's seat and rearview mirror are in the right position. If not, adjust it.

Key points:

First, the method of wearing a seat belt

1. Don't twist the seat belt.

2. The shoulder strap of the seat belt should cross the clavicle position, and the belt should be placed on the hip.

The seat belt should be close to the body.

Reminder: Airbags are also called seat belt auxiliary protection systems. If you don't wear a seat belt, the protective effect of the airbag will be reduced.

Second, the adjustment of sitting posture.

Driving in a good sitting position is not for posing, but is closely related to safe driving and ride comfort. A good sitting posture requires the driver to put his hands on the steering wheel naturally, put his back lightly on the back of the chair, look straight ahead, and put his feet on the pedal naturally. You can't bend over and drive. Sitting facing the center of the steering wheel, the weight of the wrist is naturally placed on the steering wheel, leaving enough room for elbow and knee.

Third, the adjustment of rearview mirror.

1. When the rearview mirror is adjusted, the vehicle body is in a natural driving state.

2. Put the scene in the center of the indoor rearview mirror, revealing a small part of the rear of your vehicle, so as to help judge the distance between the car body and the rear car.

3. Adjust the outdoor rearview mirror so that the horizon is in the horizontal center of the rearview mirror, and display a small part of its own body.

B, the initial steps.

After confirming the surrounding traffic safety, turn on the left turn signal, and set the gear lever to 1 (put the automatic transmission in the driving gear). Release the hand brake when the rear is safe. Seize the opportunity to start, loosen the merger and come on.

According to the traffic conditions, take appropriate acceleration methods, merge into the driveway as soon as possible, and drive normally.

Basic elements:

First, pay attention to observe the surrounding situation.

When you are ready to leave, be sure to confirm the surrounding traffic conditions. Besides looking at the left rearview mirror, you'd better turn your head and look back, because the rearview mirror has a blind spot.

Second, turn on the left turn signal.

Tell the pedestrians around you that you are leaving and remind them to avoid.

Third, grasp the starting time.

Always pay attention to the space between traffic flows, start decisively without affecting other people's traffic, and quickly enter the normal driving state.

C, special circumstances to start.

Steps for starting the ramp: Tighten the handbrake, put on the brake, and put into first gear. Release the brake, refuel quickly and lift the clutch. When the clutch is in semi-linkage state, release the brake. Come on, completely release the clutch pedal.

Key operation points:

1. Grasp the timing of semi-linkage of vehicles.

2. When the ramp starts, the throttle should be bigger than usual, and the steeper the ramp, the bigger it is.

3. Be sure to be in the clutch semi-linkage state, and release the brake after the car has a forward trend.

4. the starting action should be done in one go.

Reminder:

If the vehicle slides backwards when climbing a hill, don't worry, immediately step on the clutch brake and tighten the handbrake, and then start according to the procedure.

If you don't have time to step on the clutch or don't refuel enough uphill and the engine stops, it's just to restart the vehicle. Don't be timid, start all over again.

If the ramp is not steep, and there is no car behind it, and there is no danger of starting slightly backwards, you can start without holding the hand brake, but the starting action needs to be faster.

Start on a slippery road with snow and ice.

The steps are the same as normal startup. The key is to lift the clutch slowly and refuel slowly. If the road surface is too slippery, you can start from the second gear to reduce the torque output and avoid wheel slip. Of course, owners with traction control system (TCS) or electronic stability program (ESP) can start normally, and the electronic system can help control the torque output and ensure the smooth start of the car on wet roads.