Joke Collection Website - Mood Talk - Novice fishing, girls, how to choose fishing gear, thank you.

Novice fishing, girls, how to choose fishing gear, thank you.

1. fishing rod type: refers to fishing rod without pay-off device, which is one of the most popular fishing rods in China at present. Hand lever is divided into connecting lever and inserting lever. The joint rod can be divided into long-section rod and short-section rod. According to the use category, there are three kinds: crucian carp rod, carp rod and creek fishing rod.

Most hand rods are made of plain glass fiber cloth and unsaturated polyester, also known as FRP fishing rods. The other is made of carbon fiber and unsaturated polyester, called carbon fishing rod. Because the price of carbon fiber cloth is much higher than that of glass fiber cloth, carbon fishing rod is much more expensive than glass fiber reinforced plastic fishing rod. The strength of carbon fiber is higher than that of glass fiber, but its own weight is very light. The hand pole made of carbon fiber is lighter than glass fiber reinforced plastic under the same strength condition, so it is very popular with competitive fishing enthusiasts.

Some manufacturers produce some fishing rods with mixed materials for the sake of price and performance ratio, and the inner layer and outer layer are made of different fibers; The first three sections are made of carbon fiber, and the tail section is made of glass fiber reinforced plastic. This kind of fishing rod has certain advantages in price and performance, but it is easily misunderstood as a fake carbon rod and is not accepted by fishermen.

2. Rod length: refers to the actual length of the hand lever after assembly or deployment. The length of the practical range (referring to the method of fishing with a straight rod line) is 2.7 meters, 3.6 meters, 4.5 meters, 5.4 meters and 6.3 meters respectively. At present, the competition rules of competitive crucian carp fishing in China stipulate the use of 3.6-meter-long hand poles for competition. Usually used for leisure fishing, a 5.4-meter-long hand pole is enough. It should be said that it is very difficult to catch crucian carp with a hand pole over 6.3 meters. Because the fishing rod is too long, it is very troublesome to do. The action of crucian carp eating bait was originally small, and the float was thrown too far, and many slight signals could not be recognized.

Carassius auratus must swim from deep water to the shore where food is stored in order to feed. Whether it is a river, a lake or a reservoir, the area 3-4 meters away from the shore, with a water depth of 1.5 meters and a flat bottom, will become a feeding channel for fish, and a 4.5-meter hand pole can completely reach this range. Sometimes the fishing rod is used for too long, which will make the fishing point cross the feeding channel of the fish and lead to losses.

3. Hardness of the handle: refers to the tensile force that the handle can bear. The one under great tension has high hardness, and vice versa. Crucian carp in China, whether wild or artificially raised, weigh more than 0.8 kg. Therefore, it is completely possible to fish crucian carp with a hard-tuned hand pole.

The hard adjusting rod can not only protect the fishing line by using the drag force generated by moderate elasticity, but also try to avoid tearing the fish lip because the fishing rod is too hard. Moderate tonality can also produce a good feel, which can add a lot of fun for fishermen to walk their fish. The good elasticity of the hard adjusting rod combining hard and soft can also directly fly the crucian carp weighing about 0.2 kg ashore, which saves the trouble of copying the net, and is more suitable for competition and easier for beginners to master.

4. Tonality of the pole: Tonality actually refers to the strength of the pole, which refers to how much weight the pole tip can lift and how much radian the pole body appears when the tail section of a fully unfolded pole remains horizontal. The greater the load, the harder the tonality of the fishing rod with smaller curvature. Generally speaking, the tonality of the hand lever can be divided into five grades: middle key, middle hard key, hard key, super hard key and extremely hard key.

5. Uniformity of tonality: the radian of the fishing rod with good uniformity is in a state of gentle transition after being forced to bend; A fishing rod with poor uniformity has a dead angle in its radian.

At present, it is difficult to judge the quality of hand bars sold in stores only from the appearance, and the marked hardness often does not match the actual hardness. The uniformity of tonality is good, which is difficult to detect when the fishing rod is not actually installed. It is suggested that fishing friends test the unity of hardness and tonality when buying fishing rods, and don't be deceived by some exaggerated labels and gorgeous appearance of fishing rods.

6. Weighing inspection: When selecting a hand pole, the hardness of the pole body is tested according to a practical standard instead of looking at the tonality mark on the pole. For example, if we want to choose a cutting rod for fishing crucian carp, we will make it weigh 0.3 kg and the jointing rod weigh 0.4 kg.

Use a counterweight prepared in advance or a plastic bag to temporarily load a weighted bait as a counterweight, tie it to the fishing rod, and then slowly lift the fishing rod. When the counterweight leaves the ground, keep the tip of the lever and the bottom of the lever handle in a horizontal line. At this time, if the curvature of the fishing rod is about half the length of the rod, its hardness is suitable for fishing crucian carp. If the third quarter is obviously bent, it will be a little soft. If you just bend to the second quarter, the third quarter will hardly deform, so it will be a little hard.

7. Insert rod: Insert rod is a kind of split fishing rod in hand rod, which is called "parallel fishing rod" according to the Chinese pronunciation of Japanese characters. When in use, the insertion rod should be inserted from the top (the tip of the rod) to the end, in order to become a complete fishing rod.

Because the parting surface reduces the space for telescopic (connecting) fishing rod, the rod body can be made thinner without reducing the strength, which is the variety pursued by competitive fishing enthusiasts.

Hard-adjusting stopper rod is used for leisure fishing, and it is more suitable to catch about 0.5 kg of crucian carp. Soft and hard tonality can not only increase the pleasure and pleasure of fishing for anglers, but also be used to catch small crucian carp within 50 grams in the competition; Because of its light weight, it can save physical strength and facilitate fishermen to maintain a good competitive state in long-term competitions. At present, the plugs sold in the market are mainly 3.6 meters long, and their tonality is mostly hard and super hard, and extremely hard-tuned plugs are rare.

8. Hook lever: Hook lever is a retractable hand lever. According to the Chinese pronunciation of Japanese characters, it is called "vibrating" hand lever. The connecting rod is divided into short section (stream fishing rod) and long section (pond fishing rod). Although the short pole is easy to carry, its strength is low, and competitive fishing enthusiasts basically don't need it.

Because of their different strengths, the length of a single joint is slightly different, but the total length of the fishing rod after pulling out is not much different. Generally, the length of the tail of the long joint connecting rod is about 100 ~ 1 15cm. In order to make the rod shrink into the tail joint in turn, the connecting rod is thicker than the inserting rod.

9. Socket: the interface between the connecting rod and the upper section. Whether the wall thickness of the socket is consistent or not and whether the cross section of the socket is flat or not is an important link to reflect the quality of the plug rod.

The way to check the socket is to slowly insert the upper section into the lower section. In this process, there should be no looseness and tightness, but the tighter the insertion. There should be no sloshing at the interface after tight insertion, the sloshing fishing rod has a seamless feeling, and there is no noise caused by friction between nodes due to looseness. The greater the vacuum force when pulling out each section, the closer the upper and lower plugs are.

10. Insertion amount: the length of the upper segment of the stopper inserted into the lower segment. The insertion amount of each section should be gradually increased from top to bottom. Generally, the insertion amount of the first section (pole tip) is not less than 6 cm.

Usually, when using the insertion rod, it should be inserted from the tip of the rod in turn and slowly from the bottom. If it is inserted too fast, it will accelerate the wear of the inner and outer walls of the pole and cause looseness. After each insertion section is in place, rotate the insertion section slightly counterclockwise to lock the socket. The rotation angle should not be too large, and it is appropriate to be about 5 degrees. When exiting, turn the lock clockwise and then pull out the upper part.

Beginners, due to poor control ability, are prone to tug-of-war when fishing big fish with a plunge rod, or suddenly use too much force to break the fishing rod, so pay special attention.

1 1. Lap joint: refers to the joint between connecting rods. For a 3.6-meter hand pole, the joint between the top and the second section is generally more than 4 cm, the second and third sections are 4 cm, and the third and fourth sections are 6 cm. The lap joint is short, which is easy to cause jointing and fracture. After a period of use, it will become shorter due to wear, so choose a longer lap joint when buying poles.

12. Upper and lower openings: the upper end of each connecting rod is an upper opening and the lower end is a lower opening. Whether the wall thickness of the upper and lower openings is the same, whether the cross section is flat, and whether the outer section is in close contact with the inner section after the inner section is tightened are all important points to ensure quality and durability. In addition, the stopper rod has only an upper opening, but no lower opening.

13. Rod plug: a plug to prevent the inner section from slipping out after the hand lever is retracted, also called plug. The connecting rod has an upper plug (rubber or wood products) and a lower plug (generally plastic products), and the lower plug has a vent hole, which can release the water vapor in the rod. The 3.6m plug rod has two connected upper plugs, but no lower plug.

Every time you go home after fishing, try to pull out the plug on the rod and let the water vapor in the rod evaporate, so as to avoid long-term humidity in the rod and damage the paint surface.

14. Movable bottom handle: the detachable bottom handle is used to shorten the length of the hand lever. A 5.4-meter hand pole can be equipped with three movable bottom handles, so it can be changed into a hand pole with three lengths of 4.5 meters, 3.6 meters and 2.7 meters to achieve the purpose of multi-purpose for one pole.

Buy a removable bottom handle. Be sure to match the fishing rod for field test.

15. Knitting tip: a soft braided tube (a kind of chemical fiber fabric) glued to the tip of the pole to fix the big thread. After the new fishing rod is bought back, the pigtail tip should be treated. Starting from the tip of the pole, tie a one-centimeter-long knot at the braid tip, cut off the excess braid tip, and then bake the braid head with a lighter to make it naturally melt into a ball. So that the knot won't fall off again. Then use quick-drying super glue with good water resistance to drop a small drop of glue where the braid tip was originally bonded, and let the glue penetrate a little above the braid tip, about 5 mm, in order to strengthen the bonding degree between the braid tip and the pole tip and protect the braid from being worn off by the pole tip. But it must be noted that the glue must be dripped less. If the braid is completely soaked with glue and becomes stiff, it will be difficult to tighten the fishing line at the tip of the braid, which will cause the big line to fall off in use.

16. Insulated handle sleeve: made of insulating heat-shrinkable rubber, which can play an insulating role when sleeved on the handle of the handle bar, commonly known as the rubber sleeve of anti-electric handle sleeve. When buying an anti-electric handle cover, it must be about 5 cm longer than the handle at the bottom of the fishing rod, and the thickness should be as appropriate as possible. If the original bottom handle is wrapped with a layer of iron wire, it is best to remove the iron wire first and then install the anti-electric handle cover, so that the installation effect is more beautiful, and the diameter of the bottom handle can not be increased.

The thermal shrinkage of the handle sleeve should be considered during installation. After putting on the insulating handle sleeve, the handle sleeve should be flush with the end face of the handle at the bottom of the fishing rod. Then use a blower with power exceeding 1000 watt to gradually heat it until the sleeve shrinks and tightly wraps around the bottom handle, and then use a cutter to cut off the excess part. You can also heat it directly on an open flame, but quickly, so as not to burn the bottom handle.

17. fishing line: at present, the boxed fishing line sold in the market is mainly nylon line. Competitive fishing pays great attention to the collocation of lines, and the change of thickness is often between plus or minus 0. 1 number. For example, according to the fish situation of a certain bureau, the best line group is 0.4 big line and 0.2 sub-line. If the number of the 0.2 sub-line you use is actually 0.5 line, this combination will not achieve the expected effect, and the "inverted cow" configuration in which the sub-line is thicker than the large line will also cause the large line to be cut off.

When buying a fishing line, you should not only look at the brand and label, but also personally check the diameter and strength of the line. At present, there is no special detection tool for anglers in the market, and only external micrometer and spring scale can be used for detection.

When detecting the fishing line, first check the flatness, resilience and softness of the line by hand. Observe whether the transparency of the line is consistent in a bright place, and then measure the diameter and tension of the line. If the line diameter and tension are not much different from the values specified in this label, and the line diameter does not exceed positive 10% and the tension does not exceed negative 10%, the line is still acceptable (there is no fishing line thinner than the label and larger than the standard tension in the market at present).

Carassius auratus is timid and vigilant. It is best to use transparent line or shadowless line to fish Carassius auratus. The thinner the line, the better, which can reduce the vigilance of Carassius auratus.

18. Big line: also known as main line or bus, refers to the fishing line connecting the pole tip and the splayed ring, excluding the auxiliary line of the hook.

There are two ways to tie the big thread: one is to fold back from the thread end 10 cm, tie a fast knot next to the thread end, and then tie a double-buckle fast knot from the head end 1 cm after folding. Then pull out a scissors buckle with your thumb and forefinger, tie it to the tip of the fishing rod, measure a line 15 cm longer than the fishing rod, and then put on the accessories in the following order: put on two space beans first, the first one is used to reset the float, and the second one is used to limit the upward movement of the float. Wear one or two space beans (if the space beans are tight, wear one) to limit the downward movement of the float after wearing the floating seat. Then, the upper limit block is installed to limit the upward movement of the lead cover, and the lead cover seat and the limit block limit the downward movement of the lead cover seat. Finally, measure the length of the pole line, tie the 8-shaped ring, and cut off the redundant thread head, and the big line will be completed.

Another way to tie the thread is not to measure the thread first. After all the accessories are put on in the above order, take the 8-shaped circle as the head, measure the line 10 cm longer than the fishing rod, cut and tie it in the above way, and complete the production of the big line.

19. Wind line: When fishing, the big line floating on the water surface or in the air from the tip of the pole to before the big line enters the water is called wind line. It is wrong for some people to confuse the wind line with the big line.

20. Waterline: Waterline is composed of some big lines and sub-lines, and the line from the floating foot to the underwater hook is called waterline.

2 1. Water depth measurement: refers to the method of measuring water depth with the waterline. Adjust the length of the waterline to ensure that the hook drops to the bottom. When the float comes out of the water and is vertical to the waterline and the hook, the height from the lower hook to the intersection of the float and the water surface is the actual water depth of the fishing point. Some fishermen ignore the length of the float when calculating the water depth, so there will be no small error.

22. Secondary line: A fishing line with one end hooked and the other end tied to the 8-shaped ring of the big line is called secondary line. The auxiliary line for competitive fishing consists of double lines with different lengths. Besides being as thick as the big line, the fishing drift line is generally 0.2 to 2 times thinner than the big line, and its length is within 15 cm, which is shorter than the sub-line of Taiwan Province fishing. The sub-line is thinner than the large line to protect the large line from being cut. The thinner the sub-line, the less alert the fish is, and the thin and soft sub-line is more conducive to the fish sucking the bait into their mouths.

The method of making the special auxiliary line for competitive fishing is troublesome and requires some patience and care.

First, determine how long the sub-line should be tied, and then make a line Zhi Zi with cardboard, which is 2 cm longer than the planned sub-line. Then according to the number to be done, wind the thread around the Zhi Zi, and make a circle with one Shuang Yi and two. After cutting off the thread from the top of Zhi Zi, the same length of thread is finished. In order not to mess up the thread, you can clamp the thread together with a clip.

Draw two straight lines on the auxiliary line board where the auxiliary line is hung, according to the set hook distance and the length of the auxiliary line, so that the hooks are aligned. After putting a hook at both ends of the sub-wire, hang the double hooks on the upper and lower horizontal lines of the sub-wire board according to the preset hook distance. After smoothing the double thread, tie a double knot at the thread end, insert a steel needle (the thickness of sweater needle) at the knotted hole that has not been pulled to death, move the knotted hole up and down with the steel needle, and then gradually tighten the knot after determining the position, and slide out from the steel needle, so that the knotted sub-thread has the same length, the same hook distance and even the same knotted position. If you hook with a hook device, the line will be longer.

23. Hook distance: refers to the gap between the long and short sub-lines. In bottom fishing, the hook distance of double hooks should not be too large, generally within one and a half hook distance, but not less than half hook distance, otherwise it will affect the food intake of fish. When fishing and drifting, the hook distance of double hooks can be as large as three hook distances. If the hook distance is too small, the chances of middle-tailed and double-tailed fish will be reduced.

24. Space beans: rubber particles with strong elasticity and holes in the middle. Pull the bus bar in with its own thin steel wire. Using its elasticity and convergence, it can not only limit the movement of the floating seat and the lead seat, but also change the position of the floating seat and the lead seat. Space beans are divided into different models in order to suit fishing lines with different thicknesses. Competitive fishing generally uses the tightest and smallest space beans. In order to avoid the attention of fish, it is best not to use colored ones, but only black ones.

25. Floating seat: made of rubber with good elasticity. One end passes through the bus, and the other end can be inserted with a float, which can move freely on the bus to adjust the waterline length. Strong and elastic floating seats are most suitable for competitive fishing.

26. Lead holder: A plastic product with a hole in the middle, two tapered ends that can move on the bus, and a slot in the middle for winding the lead. There are also lead leather seats made of metal, because line loss is rarely used. Competitive fishing enthusiasts generally choose a black plastic lead seat with a slot width of 1.5cm and a head thickness of 3 mm.

27. Lead skin: a lead product rolled on a lead skin seat and used as a lead pendant. When buying lead leather, you must buy it according to the groove width of the lead leather seat. If you can't buy the right one, you can buy a wider one and cut it into the right width. It is best not to use narrow ones, so as to avoid the lead skin moving freely on the lead skin seat and reduce the accuracy of the float signal.

In addition, the lead skin is too thick to be rolled, which is not convenient to adjust the float and is not conducive to the fine adjustment of the float. Lead skin is too thin, and it is easy to be washed away by water pressure in use. If there is a small adjusting piece inside, it will be lost, thus changing the adjustment of the float. 0.25 ~ 0.3 mm thick lead skin is better to use.

28.8-shaped ring: metal connecting ring, with one end connected to the bus and one end connected to the sub-line, and the two ends can rotate freely, which is very small. The length of the 8-shaped ring used for competitive fishing of crucian carp is generally within 1 cm.

29. Duckbill ring: It has the same function as the figure-eight ring, except that one end of the tether is a duckbill-shaped clip. Just pull the buckled tether in. Duckbill ring is famous for its rapid change of secondary line, but it was abandoned by many people because of the injury of secondary line.

30. Hook: It is forbidden to use barbed hooks in domestic competitive crucian carp fishing competitions. In fact, as long as you master the correct lifting action and properly control the fishing rod after catching the fish, you don't need to use a barbed hook in any occasion. The barb of the fish hook is easy to cause harm to the human body, and it is difficult to take it off after hooking clothes. Moreover, the fish will tear its mouth if it moves a little. It is recommended that you use a barb-free hook, even for leisure fishing.

Too big a hook is a common problem for beginners, and they are always worried that the hook is too small to catch big fish. For the hook of crucian carp, the width of the hook door is preferably about one-third of the diameter of the fish mouth. When the width of the hook door is more than half, it is difficult for fish to suck the bait ball with hook into their mouth.

Non-barbed hook and pill hook are widely used in competitive fishing. Other side hooks can be used to catch crucian carp as long as the hook door is wide, the hook handle is short and the hook tip is long. When the fish situation is normal in the competition, a thicker hook is generally used. One is firm, and the other is that the weight of the hook is relatively large, which can increase the influence on drift displacement. Gold and silver hooks will alert fish, so it is best not to use them.

In addition, when buying a hook, check the rigidity of the hook. It's best not to buy a hook that opens its mouth when you pull it.

3 1. Float: a sign that can float in the water to convey fish information to fishermen. Floating can also be called floating and floating. At present, the main floats used by competitive fishermen are made of peacock feathers, balsa trees and reeds. This float consists of three parts: foot, main float and indicator. Floating feet are used to fix floating feet, including bamboo feet, carbon feet and FRP feet. The outer surface of the main floating body is coated with waterproof paint to maintain the buoyancy stability of the floating body. Markers painted with various colors are also called marker poles, floating seedlings, floating tips and floating tails. Indicators are generally divided into solid and hollow. The solid is made of glass fiber reinforced plastic products, and the hollow is a double-layer plastic pipe.

In order to meet the needs of different water depths and different fishing methods, floats are made into different shapes and sizes by manufacturers. Whether the float is practical or not, and whether its performance is excellent or not, depends entirely on the float manufacturer's understanding of the sport of fishing crucian carp, the choice of manufacturing technology and the pursuit of quality.

32. Long-body float: A float with a slender main float, a slender indicator and a moderate floating foot length, which is specially used for bottom fishing, bottom fishing and deep water fishing. This kind of float has small resistance to water when moving in water, good stability, uniform and slow secondary sinking after standing, and long stroke, which is especially suitable for capturing the signal of crucian carp "intercepting" from the bottom of the water. It is extremely sensitive to the slight tension and reaction caused by fish sucking bait at the bottom, and is an essential float for fishing bottom.

There are two kinds of long body drift: long body and long tail (index) and long body and short tail. The long tail can reach 12 mesh to more than 20 mesh; The short tail is within 12 mesh, and if it is soft, it is about 7 mesh.

The longer the floating body is, the thinner the indicator is, and the more sensitive it is. However, if the fishing tackle is not properly adjusted, it will also reduce the sensitivity or be too sensitive, and false signals often appear.

33. Short-body float: a special float that stands quickly after entering the water and is suitable for fishing. Some people also call it jujube pit bleaching. Short body, short tail, short feet, total length 10 cm, and short body drift that is not too thick are more suitable for fishing in the upper water layer. Short body, long tail and long feet are not suitable for fishing.

At present, the short-body floats sold in the market are basically used for drift fishing and ice fishing. Although it can also be used for competitive crucian carp fishing, it is not ideal. Many competitive fishing enthusiasts have changed their soft tail and short body drift, leaving only four eyes for marking and short feet for drifting.

34. Sudden shoulder floating: also known as blunt shoulder floating. Because the root of the main floating body of the float is an umbrella-shaped inclined plane, when the float loses traction in the water and floats up, the water has great resistance to its end face, which makes it unique and especially suitable for catching slippery fish with fast bait.

35. Big belly float: A float with short body, long tail and short feet. Because of the relationship between materials and processing technology, this float is partly made of wood products. Dadu drift has low center of gravity, fast standing speed, and relatively long pause time before secondary sinking, so it has advantages in fishing middle and lower crucian carp.

36. Soft floating: At present, it refers to the floating of peacock feathers with shells used for fishing crucian carp. This kind of float can be slightly bent, its buoyancy is greater than that of peacock feathers with the same volume of shells, its sensitivity is high, and it is easy to break if used improperly.

37. Hard floating: In the past, peacock feathers floated with shells. Now it generally refers to a float that cannot bend. Floats made of peacock feathers, wood, reeds and porcupine spines are all hard floats.

38. Fishing box: fishing tackle necessary for competitive fishing. It can not only store bait, food basin and other items, but also be used as a seat, or as a connector for placing poles, food boxes and fish protectors.

Fishing boxes are plastic products, which are sized according to the volume (liter). When buying a fishing box, you must choose the size according to your height. It is advisable to sit on your lap at an angle of about 70 degrees.

39. Fishing box fittings: refer to fittings fixed at different positions at the front end of the fishing box with metal screws to connect the placing rod, the food box and the fish guard. It is an essential accessory for competitive fishing. There are two kinds of accessories: plastic and stainless steel. Due to the different materials and processing difficulties, the prices of the two types of accessories are quite different.

40. Fishing box accessories: Like the umbrella frame installed behind the fishing box, it can be used as an adjusting foot to adjust the stability of the fishing box. Cushion installed on the fishing box cover, folding with backrest, and rod hanger installed on the side of the fishing box for temporary rod insertion are all accessories. These accessories are not necessary and can be installed according to personal hobbies and needs.

4 1. Hook puller: a slender metal or plastic product with a front fork. When the hook hangs deep in the mouth of the fish and can't be taken down by hand, jack it down.

42. Fishing device: a slender stainless steel brazing rod installed on the fish guard ring. Hang the fishhook with fish on the drill rod, and pull the auxiliary line to make the fishhook rotate downwards, so that the hook tip is downward, and the fish will automatically slide down from the barb-free fishhook and fall on the guard plate.

43. Bait-pulling tray: The center of the tray is stuck with electroplated strong magnetic sheet or magnetic strip, which can independently absorb auxiliary appliances convenient for bait-pulling with double hooks. There are many kinds of bait plates, and you can also make them yourself because they are simple. At present, the popular bait tray only sticks a strong magnetic strip 5 cm long. Some fishermen can still pull out beautiful bait particles without pulling the bait tray.

44. Fish protection: competitive fish protection requires a large mouth protection, a length of two meters (to ensure that all kinds of fish can enter the water), and a protective net of no more than 1 cm. Don't be too bright in color, so as not to scare the fish.

45. Copy the net: The net for competitive fishing should not be too big, just about 30 cm. The net bag should not be too deep, otherwise it is easy to break the string and it is also troublesome to fish. The total length of the net is l.8 ~ 2 meters. Some net-copying handles are exquisite but too short, and it is inconvenient to copy fish when the water level is low, which affects the game.

46. Fishing glasses: Although fishing glasses are also sunglasses, they must have a polarizing effect, and try to filter out the reflection of water waves, so as to facilitate observation of drifting in the sun.

47. Fishing hat: The biggest difference between fishing hats and other sports hats is that the brim is very long, which is more conducive to shielding the sun. In addition, an extra hat belt will not blow the hat away when there is wind. Japanese fishing hats, those with hats are sea fishing hats, and those without hats are freshwater fishing hats.