There is no sound on the landline. What's the matter?

question 1: what if there is no sound on the landline? 1. first unplug the incoming line and connect it directly to a good telephone to see if it works. If the telephone is not normal, it may be a fault of the telephone, so replace it or take it to the maintenance department for maintenance (which does not rule out the problem of the communication company). If the normal side of the telephone proves the cause of the line between the separator and the telephone, first carefully check the line to see if it is broken or the connector is disconnected, and replace it or reconnect it.

2. Incorrect installation of the separator leads to or no separator, too many extensions and the separator is broken. Please make sure that a separator is installed in front of each phone, or the phones are connected behind the phone port of the separator. The modem port on the separator is connected to the "cat", the line port is connected to the household line, and the phone port of the separator is connected to the telephone. If there is a telephone extension that must be connected to the line extension between telephones from the phone port of the separator, it is best to buy another separator to connect the extension line to the phone port from the line port to answer the telephone.

3. Communication company's problem is that broadband and telephone equipment are two devices. If the port line of telephone equipment is loose, the telephone will not work, just dial 112 and ask for repair.

Question 2: There is no sound on the landline at home. If there is no dial tone, it means that the line is faulty, short-circuited, or in arrears. The telecom number is 1. If there is no sound when the landline at home lifts the microphone, but the broadband Internet access is normal, this situation is generally caused by a broken one of the telephone lines, because the telephone signal must be transmitted by two lines, and only one broadband can be transmitted (of course, the speed will be slowed down by half). Thank you.

Question 3: What if there is no sound when the landline phone calls? What's wrong? Thank you! ! Find a professional one, and fix it for free.

``` On the network, without knowing the specific situation of hardware, It's hard to solve'

maintenance is the first choice''

Question 4: When the landline is picked up, there is no sound or beep in the receiver. What's the matter? It's very simple. Call the customer service with your mobile phone. Call the customer service at 1. Tell the customer service about the problem with your landline. She will arrange for someone to come to your home for maintenance or help you with it in the computer room. I have encountered this situation before. It's exactly the same. It's useless to change the battery and the line. The last call will be made. I don't need maintenance personnel to come to my home for maintenance. It's fine. I guess I did it in the computer room.

Question 5: What if there is no sound on the landline? Big brother. Looking for your telecom company. This problem is their problem. As for your saying that broadband is easy to use, it's two different things. Sometimes even if one of your telephone lines is broken. Broadband still works. Besides, your situation is definitely not disconnected. It's probably geogas or short circuit. You can't fix any of this.

Question 6: What's wrong with the incoming call from the fixed telephone? Make sure that the telephone bill has stopped. If not, check the battery of the telephone. If it doesn't work, call someone to see if there is something wrong with the external telephone line. Last time, someone else was able to get through to my home phone, but my phone didn't respond. Later, call someone to see if there is something wrong with the external line, and it will be fine.

Question 7: There is no sound on the fixed telephone, but the indicator light is on. This is obvious. There is no sound on the fixed telephone, but the indicator light is on because the microphone or network cable is not connected properly. If it is connected properly, see if the phone lock on the back is locked. Generally, there is no sound when the phone is locked.

Question 8: What's wrong with the landline phone with numbers but no sound? First, consider the part where the cat line is separated from the telephone line, and then consider the crystal head of the telephone interface.

Question 9: What's wrong with the phone picking up the microphone without sound? This is a telephone line problem. The telephone uses a low-frequency voice signal, while the broadband uses a high-frequency data signal. When the telephone line is slightly disconnected, the low-frequency signal can't pass, but the high-frequency signal can pass, which is equivalent to the principle in physics that the capacitor is a path for AC and a circuit for DC. You can directly report the trouble to the operator's customer service and have it repaired.

Question 1: What is the reason for my phone's silence? Can't get in or out: Reason: It is caused by telephone failure or line problem, switch failure, arrears and other reasons. 1, arrears users. It is suggested to pay the fee as soon as possible, and we will open it within 3 hours. 2, stop the number of users. If you need to use the telephone, it is recommended to re-open it. Pick up the phone and see if there is a current sound. If there is a current sound but you can't dial it, there will be a prompt, which will be judged by the prompt sound. If there is no current sound when the phone is picked up, it is recommended to check whether the line is connected properly, whether the line is broken, whether the crystal head is loose, and whether the phone is faulty; 2. Check whether the line is connected with a separator. If it is connected with a separator, you can take the separator away first and connect the telephone directly. If it is normal, it means that the separator is faulty; 3. If the lines are connected normally, but there is still no current tone on the phone, please call 1 to report the fault. Can only make calls, but can't call in: the phone is not hung up properly, the phone is out of order, or the phone has made a call transfer, and our exchange is out of order. 1. First of all, what are the tips if you can't get in? 1) Tip: The number you dialed is faulty: most of these faults are caused by the long-term failure of the home phone. It is recommended to check whether the phone is in place. 2) Prompt: The number you dialed is temporarily unavailable, turned off, and does not exist. Because the phone made a call transfer. It is recommended to cancel all call forwarding and try again. 3) Make sure the phone is hung up and call forwarding is not set. Please call 1 to report the fault. Operation of call forwarding: 1. Call unconditional forwarding: Registration method: *57* specified phone number #; Logout method: # 57 #. 2. Call forwarding without answering: Registration method: *41* designated phone number #; Logout method: # 41 #. 3. Call forwarding when busy: Registration method: *4* designated phone number #; Logout method: # 4 #. Can only dial in, but can't dial out: It is caused by subscriber lines, switches, arrears, or call barring. 1. Prompt for arrears: It is suggested to pay the fees as soon as possible. 2. Calling prompt is restricted: it is a stop number. If you need to use this phone, you can dial it after opening it. 3. Another possibility is that the calling authority has been restricted because of the "outgoing call restriction" function. It is suggested to cancel the "outgoing call restriction" function and try again. 4. Finally, you can check that there will be no problem. If there are no problems, please call 1 to report the fault. Loud noise: caused by problems such as lines, switches or telephones. 1. First, check whether the telephone line contact at the customer end is good. 2. If ADSL is installed, the separator must be connected. Can't connect the extension before the separator. The LINE port of the separator is connected with the incoming line. The MODEM port is connected to the MODEM device, and the PHONE port is connected to the phone. If you make sure that all the lines are in good contact, the wiring is not abnormal, and the telephone is not faulty, please call 1 to report the fault. No caller ID: The caller ID may not be enabled on the phone, the phone terminal problems, the other party's restrictions or data signals. 1. Is caller ID enabled? If not, you can bring your ID card to the business hall to enable caller ID or call 1 to apply for it. 2. Are the numbers that can't be displayed regular: 1) They are never displayed or not displayed at all. It is recommended to try changing the phone or the phone battery; If it doesn't work after trying, please call 1 to report the fault; 2) Some numbers are not displayed, and it is determined whether there are restrictions or data signals. If not, please call 1 to report the fault. Unable to make a long distance call: it may be caused by business failure, switch failure, line failure, or telephone itself. 1. First, determine whether you have applied for the long-distance function. (If you don't apply for the long-distance function, you have to bring the owner's ID card to the business hall to open it or dial 1 to apply for opening it. 2. It is impossible to make a long-distance call by using other telecom operators (for example, 17951). (Use other operators' access numbers to make long-distance calls, without opening the long-distance function. 3. If you have the function of applying for long distance and the function of applying for outgoing call restriction, you must cancel the outgoing call restriction before you can make long distance calls. 4. Some phones have phone lock function. It is suggested that you need to open the phone lock before you can dial on the phone. If the problem still cannot be solved, please call 1 to report the fault. Crosstalk/phone suspected of being stolen: it may be caused by damp telephone lines, poor contact, switch failure or phone problems. 1. First, check whether all lines are in good contact, and if there is a separator, connect the lines in the normal way. L of the separator >; >