Site safety inspection

It is necessary to conduct on-site safety inspection according to the on-site safety inspection system. The following are the main points and systems of on-site safety inspection that I have compiled for you. Let's have a look!

? Key points of safety inspection on construction site

? 1. Construction site fence: closed with hard materials or brick masonry (the wall height of main sections in urban areas is 2.5m, and that of general sections is 1.8m), and the wall surface shall be plastered and painted to be firm, flat, neat and beautiful. There should be a wall cap around the brick and a propaganda slogan on the wall. It is not allowed to pile materials or soil against the wall. If conditions permit, color pressed steel plates can be used.

? 2. Site gate: battlements and gates. Set a light box above the door with the name of the enterprise and the name of the project on it. The guard room should have a guard system and be placed at the gate. Construction is important, and idle people are not allowed to enter. ? And then what? Safety helmet must be worn on the construction site. ? Brand. There are seven pictures and three cards hanging in the door.

? 3. Ground of the site: hard ground with good drainage (the main roads in the hardened site are not less than 20m, and not less than 5m outside the site), and it is equipped with a washing table.

? 4. Personal protection: wear a safety helmet and fasten your seat belt, and hang it high and use it low. Sambo? There must be production license, product certificate and quality inspection certificate.

? 5. On-site access: A protective shed shall be erected at the entrance of the access, with the shed being wider than the crossing, and scaffolding shall be erected at the top of the shed. The shed length should be greater than 3m; Buildings with a height of more than 24m should be provided with double-layer protection, with the spacing not less than 60㎝ and the shed length exceeding 10m.

? 6. Elevator wellhead: a fixed grid or two-way fence with a height not less than 1.2m(60㎝ one, 120㎝ one) shall be set, and a flat net shall be set every 10m in the elevator room.

? 7. Edge protection: Two protective fences with heights of 60㎝ and 120㎝ shall be set for the edge facilities such as balcony, roof, floor, stairs and unloading platform, and columns shall be set with a spacing greater than 2m.

? 8. Scaffolding: It is forbidden to mix steel and wood in material selection, and the material meets the standard. Before the scaffold is dismantled, it is not allowed to dig the foundation on the side.

? 9. Reserved holes: holes larger than 25㎝ are protected by fixed cover plates, and holes larger than 50㎝ are surrounded by two horizontal railings not less than1m.. For the hole larger than 1m, two horizontal railings and a safety net must be set under the hole.

? 10. hazardous area: should the hazardous area be hung on site? Forbidden? 、? Warning? Wait for the danger signal.

? Safety inspection system

? Safety inspection is an important means and measure to eliminate hidden dangers, prevent accidents and ensure safe production. In order to continuously improve the production conditions and working environment, so that the working environment can reach the best state. In order to take effective measures to eliminate unsafe factors and ensure safe production, this safety inspection system is formulated as follows:

? 1. Safety inspection content: check the implementation according to the grading standard of safety inspection on the construction site issued by the Ministry of Construction; Protection of the base groove edge; Construction electricity, safety facilities of construction machines and tools, operation behavior, correct use of labor protection articles, safety and fire prevention, etc.

? 2. Safety inspection methods: regular inspection, surprise inspection, professional inspection, seasonal inspection, inspection before and after holidays and regular inspection.

? Three, the project department construction site inspection once a week, organized by the project manager; Each construction team carries out daily inspection, organized by the construction director, and the production team insists on daily self-inspection of the working procedures in their respective environments to eliminate unsafe hidden dangers at any time.

? 4. Surprise inspection: In the event of major casualty accidents, equipment accidents, traffic accidents and fire accidents in the same industry or brother units, in order to learn lessons, preventive measures are taken and surprise inspections are organized according to the nature and characteristics of the accidents.

? 5. Professional inspection: in view of the sudden problems existing in the construction, such as construction machines and tools, temporary electricity consumption, etc. , organize individual inspections and carry out special treatment.

? Six, seasonal and holiday inspection: according to the climate characteristics, such as winter, summer and rainy season may bring harm to the construction, in advance to do four prevention in winter, summer heatstroke prevention and cooling, flood control in rainy season; Before and after major holidays, it is necessary to do a good job in safety education and implement safety precautions to prevent employees from being lax in discipline and thinking paralysis.

? Seven. Regular inspection: safety functional personnel, project management department and safety officer on duty should often go deep into the construction site to carry out preventive inspection, find hidden dangers in time, eliminate hidden dangers and carry out standardized construction normally.

? Eight. Handling of hidden dangers of accidents: All inspections must be careful and meticulous, leaving no dead ends. An accident hidden danger account should be established. For major accidents, it is necessary to fill in the accident hidden danger instruction book and designate a special person to make rectification within a time limit.