Tunnel security hazard log

Log refers to work log. Below, I will share with you the tunnel safety hazard log, I hope it will be helpful to you!

How to fill in the safety log if there are potential safety hazards (one piece every 3-4 days)

1. Is there one at the construction site? The person was not wearing a safety helmet.

Corresponding corrective measures:

Construction workers must wear safety helmets correctly when entering the construction site. Provide verbal education to those who are not wearing safety helmets and ask them to go back and get them immediately.

2. Welders do not wear glasses when working.

Corresponding corrective measures:

Welders must wear protective goggles when working. Provide verbal education to welders who are not wearing eyewear and ask them to go back and get it immediately.

3. There are non-construction workers at the construction site.

Corresponding corrective measures:

Construction workers are not allowed to bring non-construction personnel into the construction site. Provide verbal education to offenders.

4. The safety distance between oxygen bottles and acetylene bottles does not meet the requirements.

Corresponding corrective measures:

The distance between oxygen bottles and acetylene bottles must be 5m.

5. Low-voltage lines in the construction site are directly tied to poles, trees, and scaffolding in areas with frequent human activities.

Corresponding corrective measures:

Low-voltage lines at the construction site must use insulated wires in areas with frequent human activities; insulated wires must not be laid overhead in bundles, and must not be directly tied to power lines. Do not drag on poles, trees, or scaffolding on the ground.

6. Distribution boxes and switch boxes lack similar warning signs such as “Keep away from danger”.

Corresponding corrective measures:

Distribution boxes and switch boxes must be installed securely for easy operation and maintenance, and similar warning signs such as "Keep away from danger" must be displayed.

7. The low-voltage lines in the construction site use insulated wires in areas with frequent human activities, but they tend to be dragged on the ground.

Corresponding corrective measures:

Low-voltage lines within the construction site must not be dragged on the ground.

8. When leaving get off work, the power supply was turned off and the distribution box was not locked.

Corresponding corrective measures:

After get off work, the power must be turned off and the door must be locked before leaving.

9. Expose oxygen bottles and acetylene bottles to strong sunlight.

Corresponding corrective measures:

It is strictly forbidden to expose oxygen bottles and acetylene bottles to strong sunlight; they must be placed upwind of the operating point to avoid explosions.

10. The distance between oxygen cylinders and acetylene cylinders and welding, cutting torches and open flames does not meet the requirements

Corresponding corrective measures:

Oxygen cylinders, The distance between acetylene cylinders and welding, cutting torches and open flames must be at least 10m.

11. The lighting wires in the employee dormitories are pulled and pulled randomly

Corresponding corrective measures:

Remove the wires that are pulled and pulled immediately and replace them The electrician will unify the wiring.

12. The storage of candles in individual employee dormitories poses a fire safety hazard.

Corresponding corrective measures:

Thoroughly inspect the employee dormitories, confiscate and destroy all candles, and provide safety warnings and education to personnel who store candles privately.

13. Some workers during the tunnel anchor drilling construction did not wear dust masks, and the dust environment seriously threatened the personal health of the workers.

Corresponding corrective measures:

Warn and educate those who are not wearing dust masks, and ask them to go back immediately to get dust masks, and wear them correctly before anchoring. Rod drilling operations.

14. The construction access roads raise a lot of dust, which seriously affects the construction environment, the image of the team and the health of the workers.

Corresponding corrective measures:

Immediately spray water to reduce dust and clean up garbage and dust to ensure a civilized, healthy and safe construction environment.

15. Workers in the steel bar processing shed play and chase each other during the steel bar processing process, which poses a huge safety hazard.

Corresponding corrective measures:

Give verbal warnings and education to those who participate in the play and play, and fines will be imposed if they offend again.

There are no safety hazards in the tunnel safety log:

1. Construction workers should wear safety helmets correctly when entering the construction site; welders should wear glasses when working.

2. Do not work under the influence of alcohol. If found, clear the site once to eliminate unsafe factors;

3. There are no construction workers at the construction site.

4. The safe distance between oxygen bottles and acetylene bottles is greater than 5m.

6. After the holes are formed, the holes that will not be used for the next process are covered with thin wooden boards for protection.

11. The low-voltage lines in the construction site should use insulated wires in areas with frequent human activities to prevent them from being dragged on the ground.

12. The distribution box and switch box are firmly installed and have warning slogans.

13. For electrical equipment, implement "one machine, one gate, one leak, one box, one lock"; the distribution box has no exposed wire joints and is well grounded.

14. After inspection, the electric wires and electrical external connections at the construction site are not damaged, exposed or aged.

15. Electrical equipment and circuits are well insulated, and there is no direct contact between wires and metal objects;

17. When leaving get off work, turn off the power supply and lock the distribution box.

19. When the electrician stops working, the welding clamp hangs up and the cable collection hangs up.

20. The distance between oxygen bottles and acetylene bottles and welding, cutting torches and open flames is more than 10m, and the distance between oxygen bottles and acetylene bottles is more than 5m, which meets the requirements.