Ask for a driver's license subject 2 exam process

First, log in:

1. Candidates must hold their ID card and admission ticket and go to the waiting hall 30 minutes in advance to check their fingerprints according to the appointment date and examination times and get the sign-in number;

2. The sign-in number is the certificate of boarding test. During the exam, the examination room only calls the number, not the name.

Second, to be tested:

1. After entering the waiting hall, candidates should abide by the discipline of the examination room and must not make noise or walk around at will. If they need to leave temporarily while waiting, they need to apply to the staff for departure registration;

Please pay attention to the call number broadcast in the lobby and the information displayed on the lobby screen. The voice prompt of the call is "Please take the exam from * * * to * *";

3. Take the corresponding exams as soon as possible.

Third, get on the bus:

1, quickly adjust the seat, rearview mirror and fasten the seat belt after getting on the bus;

2. After everything is ready, verify the fingerprint and enter the corresponding road test according to the voice prompt.

After entering the exam channel, take all the exams in turn and complete the exams as required.

Extended data

Contents and skills of subject 2 examination

begin

1. "Start the exam, please start", and then move on. When the front of the car enters the right induction line of reversing storage, the voice broadcast: "Reversing storage" stops immediately when the right induction line is aimed at the driver's seat.

Back to the warehouse

2. Back the car into storage, put it into reverse gear, and enter the next exam through the right induction line after backing it into storage in the right garage. When the car comes out of the right induction line, it will hear the voice broadcast "This project has been completed". It is not allowed to press the corner to compact the line (from the starting point) and other parking spaces. You should enter the next exam through the back door.

quarter turn

3. Right-angle turn, when the preceding vehicle approaches the guide arrow, broadcast "You have entered the right-angle turn test project" and report "Project completed" when turning out. When entering the right-angle turning area, the vehicle speed should be slow, and the right front wheel should aim at the triangle of the guide arrow of the road sign on the ground and run over it. The left corner of the front is next to the left line, or the gap in the front cover presses the left line and moves slowly forward. (Observing the front of the car) After adjusting the direction, swing your head to the right.

Slope fixed point

4. Stop and start at a fixed point on the ramp. For example, after completing the exam at a right angle turn, enter the ramp and stop at a fixed point. You can climb slowly by stepping on the semi-clutch, adjust the direction in advance, help the preceding car climb, and turn on the left turn signal immediately after stopping at a fixed point. Start going uphill in 30 seconds. If you pass the specified parking performance on an uphill slope, you will hear a "clang". Don't turn off the engine when starting, don't slide backwards, and don't rush forward.

Tandem parking

5. Stop at the roadside. When you hear the sound: you have entered the side parking, stop immediately and put into reverse gear to complete the side parking. After parking in place, it will make a "clang". When moving the car, pay attention to stop when the right corner is exposed, and don't press the front line. When the left rear wheel approaches (or presses) the green paint edge line about10cm, hit all directions to the left. Put in first gear after parking! Ten points will be deducted for outbound line pressing.

curve

6. When you hear the computer voice broadcast: You have entered the corner. At this time, enter the entrance to the right corner of the curve, and make sure to keep a distance of 30 to 50 cm from the left corner or drive slowly and evenly from the middle, while making a 90-degree circle to the right. When driving to the middle of the curve, the left circle will return to the flat direction, then make a 90-degree circle to the left while driving at a constant speed in the left curve, and then make a 90-degree circle to the right.

End the exam

7. After the curve is completed, the computer will broadcast "Project completed" by voice, and park the car in the waiting area to wait for the voice broadcast "The test result is qualified and the result is being uploaded". You can only get off the bus if you pass the exam. Don't loosen your seat belt in a hurry.

Refer to Baidu Encyclopedia-Subject 2