Functional characteristics and installation instructions of induction shower head

In fact, the shower is composed of sensor and solenoid valve nozzle, and the induction shower can also be divided into two specifications: hidden and exposed. The following large rabbit edge show you the main functions and characteristics of the induction shower.

Main functions and characteristics of induction shower:

1, saving water, automatically sensing people coming and going, and the water saving effect is very obvious, reaching more than 30%-50%.

2. Hygiene, water comes out when people arrive at the nozzle, and water comes out when people leave, effectively preventing bacterial cross-infection.

3, waterproof, completely sealed with epoxy resin, long service life.

4, anti-fog, anti-fog technology in winter, especially suitable for places with low temperature in the north.

5, near objects, patented near object blocking function, to avoid artificial near object blocking caused by continuous water.

6. The maintenance is convenient, and the nozzle has strong anti-scaling and anti-fouling functions. A filter screen that is easy to disassemble is installed at the water inlet, which can be easily maintained by non-professionals.

7, intelligent, the sensor is controlled by a microcomputer, and the sensing range has been set before leaving the factory, so manual debugging is not needed.

8. Safe. This product adopts 24V safe DC power supply, which is safe and reliable. The shower elbow is designed with a water outlet, which is fixed by a special bracket to prevent malicious pulling and damage.

9, easy to install, suitable for all kinds of newly built or rebuilt baths.

Installation and use of induction shower;

Steps: Design water supply pipeline →→→→ Install water supply pipeline → Set power supply circuit → Flush pipeline → Fix bottom plate → Connect power supply line → Test water and adjust it → Use.

1, the power supply of the induction shower must be dry, pay attention to safety, make it easy for people to press it, and the distance of the power supply should be

2. When the main power cord passes through the tee junction box, a 4 cm long U-bend shall be left. After peeling, the randomly distributed power cord should be connected with red, black and negative electrodes. The connector should be tightly wrapped with waterproof tape, and the end of the power cord with waterproof plug should be thrown out for use.

3. When installing the induction shower, be sure to fix the bottom plate. It is best to mark the outer edge of the bottom plate at the fixing hole, and then punch 4-6 holes, with the hole depth. 29 mm? , and then fix the bottom plate. Remember to stick tape around the hole when knocking on the tile to avoid damaging the tile and ensure that the hole is straight.

4. Straighten the fixing seat 25cm above the bottom plate according to the position of the center of the outlet pipe, then make two Ф 6 holes and insert the Ф 6 plastic expansion plug.

5. If the power supply is open wire, constant temperature water supply: Install φ 16mm PVC conduit under the tee junction box, and its length should be aligned with the upper edge of the bottom plate. Thread the power cord into the conduit and connect it with the main water pipe, and the water inlet pipe is connected to the machine; Then the fixed seat is sleeved into the water inlet pipe and the line pipe in turn, and then the fixed seat is fixed on the wall with two M4×30 stainless steel self-tapping.

6. Insert the power cord through the PVC conduit into the bottom plate from the notch at one side of the water inlet pipe of the bottom plate, and then connect the two plugs of the controller with the power cord and the solenoid valve respectively. Because it is used in humid environment, please be sure to plug the waterproof plug tightly. Fasten the shell from top to bottom, screw in two M4×8 stainless steel tapping screws at the lower end of the shell and fix them with the bottom plate.

7. Pass the upper decorative plate through the water outlet and the water inlet at the same time, and press it into the top of the shell; Then straighten the water inlet pipe and connect the 4-point rubber pad to the water inlet; Then, the water outlet pipe locking nut is sleeved on the snap ring from the upper end of the water outlet pipe, and the conical rubber sleeve is sleeved on the lower end of the water outlet pipe and inserted into the water outlet locking nut; The upper end of the water outlet pipe is put into a fixing seat, pressed with a fixing cap and fixed with two M4× 15 stainless steel tapping screws; Then assemble the shower head, put a 4-point rubber pad on it and screw it to the water outlet.

8. Paste the "Instruction Manual". Please wipe and dry the wall before pasting. Be sure to stick it straight, straight and flat.

9, check the pipeline again, and then drain the water, observe whether there is water leakage, and properly handle it; Then turn on the power supply and test whether the nozzle is sensing normally, discharging water and stopping water.

Induction shower has many advantages, which is the pursuit of modern life. It is not only water-saving and safe, but also very unique and individual, which is the fashion pursued by young people. Today, Bian Xiao mainly introduces the main functions and characteristics of the induction shower, as well as the installation and use instructions of the induction shower for your reference.

Tubatu Online provides you with "each decoration quotation, 1-4 local decoration companies, 3 sets of decoration design schemes" and the decoration pit avoidance strategy for free! Click this link:/Zhu Ye /zxbj-cszy.php? to8 to _ from = SEO _ zhidao _ m _ jiare & amp； Wb, you can get it for free ~