Joke Collection Website - Bulletin headlines - Matters needing attention and details of subject 2 examination
Matters needing attention and details of subject 2 examination
Matters needing attention in subject 2 exam
1. Five things to pay attention to when getting on the bus
1. If there is no limit on the starting time after getting on the bus, close the door first and pay attention to whether the door light is off, which is the key.
2. Step on the clutch with your left foot, hold the steering wheel with your right hand, and adjust the seat with your left hand. Adjust the left foot to make it bend a little, and try to stabilize the seat by moving it back and forth.
Adjust the backrest to a 9-degree angle, and pay attention to whether it is stable before and after. Then put your hand on your head and measure whether the height is the same as usual. If it is too low, you must put the seat cushion and adjust it.
4. Adjust the left and right rearview mirrors to a proper position. Main points of adjusting the left rearview mirror: put the horizontal line at the midline of the rearview mirror, and then adjust the edge of the car body to occupy 1/4 of the mirror image; Main points of adjusting the right rearview mirror: put the horizontal line in the 2/3 position of the rearview mirror, and then adjust the edge of the car body to occupy 1/4 of the mirror image. There is still an opportunity for debugging before reversing into the warehouse. At this time, the rearview mirror angle should be debugged downward until the fender above the rear and rear wheels is seen.
5. Try the clutch again after you fasten your seat belt. Step on the clutch with your left foot to the end. You must bend your left foot a little to make it strong before you start the exam. Otherwise, readjust it, step on the brake again, try to add the accelerator, and make sure there is no problem.
Second, clutch control
Subject 2 should be steady, slow and uniform, and the clutch must be well controlled. If there are signs of parking when the direction hits one and a half laps, you should loosen the clutch immediately, otherwise you will be given a "midway stop" within 3 seconds. On the contrary, it is necessary to press the clutch a little when the direction is turned back, otherwise the test car will rush up like a horse, especially when parking on the side, which is a technical job and should be bold and cautious.
Third, stop in the middle
1. The new test regulations are abnormal. If the speed suddenly slows down from fast, it will be counted as stop in the middle regardless of whether your car stops or not, so it's better to control the speed well. It doesn't matter if you slow down. The key is uniform speed!
2. There is a sensor in the car. Some places are installed on the clutch, and some are installed on the brake pedal. Don't loosen the clutch greatly after starting, otherwise it will be counted as stopping in the middle. Try to find a suitable reversing speed immediately after starting, and don't move the clutch.
3. It is easy to stop halfway without stepping on the foot brake. When stopping, the foot brake must stop.
4. Anti-skidding car with brake
The venue of the examination room is uneven, and it is easy to slide back when starting. Pay attention to the fact that the clutch with brake is loose to the critical point before loosening the brake, and starting with brake can avoid skidding. Slowly lift the clutch until the body shakes slightly before releasing the brake. The same reason as starting on a slope, to prevent slipping. Practice step by step, the exam without step can't stand the test, because you are not familiar with the examination venue and car, and you can only pass the exam if you make the familiar steps. Why do some students practice well at ordinary times? They always say that exams are tense and their minds will be blank. It is because there are no steps in their usual practice.
5. Other notes
1. Confirm your own exam channel, and if you make a make-up exam on the spot, you must return to the original channel exam. Last time, one of my classmates took the exam in the third channel, and when they backed into the warehouse, they hung up. The driver came to drive back and parked the car at the starting point of the fourth channel, so this classmate got on the bus in confusion. Unexpectedly, when the exam was over, the computer prompted "I was uneasy about walking on the prescribed route, and failed".
2. Because subject 2 is different from subject 3, you can scan the gear with the corner of your eye when you shift gears. Don't shift the first gear to the third gear, and shift the reverse gear to the fourth gear, and you will be judged unqualified at the beginning.
3. When practicing at ordinary times, do not look at the steering wheel, or you will miss the train when parking sideways.
What should I pay attention to in the second exam of subject
The first thing I should pay attention to in the second exam of subject is my own emotions, and don't be too nervous, followed by the skills of those five subjects.
1. Back the car into the warehouse slowly, control the speed, find the reference point accurately, and try to straighten the car body when backing up, so it is not easy to press the line. When reversing into the warehouse, you'd rather hit the steering wheel earlier. If you hit it earlier, you can turn the direction back, back it up and kill the steering wheel.
if you call late, it is usually difficult to remedy. Observe the left rearview mirror when entering the garage, and return to the positive direction when the car body is parallel to the line.
after warehousing, stop when the lower edge of the left rearview mirror coincides with the corner line of the warehouse. 2. Side parking When parking in the side direction, turn the steering wheel faster.
You can see the position of the library angle A in the right rearview mirror. When the angle A is just about to leave the rearview mirror, make a full direction to the right. Then look at the left rearview mirror. When you see the corner B behind the garage, turn back to the positive direction, and then look at the left rear wheel from the left rearview mirror. When the wheel just hits the virtual garage line, kill the direction to the left and enter the garage.
when leaving the warehouse, be sure to turn on the left turn signal. 3. When driving in a curve, try to slow down the speed and adjust the steering wheel slowly. Don't hit too much at once.
when approaching a curve, you can make the car body slightly to the right, let the car body go straight ahead until 2/3 of the front of the car presses the line, and then slowly turn the steering wheel to the left, so that 2/3 of the front of the car keeps pressing the line until the first curve. In the second corner, when the car logo presses the line, turn the steering wheel back to the right. When two-thirds of the whole car head presses the line, slowly turn the steering wheel to the right, so that the two-thirds of the car head keeps pressing the line all the time. You can observe the right rearview mirror to prevent the right wheel from pressing the line, and slowly drive the car out of the corner.
4. Slow down when turning at right angles, and don't press Angle A.. When turning, you can look at the position relationship between the steering wheel and the corner, find a suitable position for yourself, and pay attention to controlling the speed of steering wheel.
5. Fixed-point parking and starting on the ramp (1) When carrying out fixed-point projects on the ramp, pay attention to adjusting the distance between the car and the right line before going uphill to avoid pressing the line. ⑵ When fixing a point, it is generally based on the individual's suitable point, so that the lower edge of the mirror fits the upper edge of the thick yellow solid line, and the fixed point is accurate at this time.
(3) When starting, don't forget to turn on the left turn signal, put on the brakes, prevent the car from slipping, and slowly release the clutch until the car body shakes, slowly release the brakes and the car starts. In this process, if the flame is turned off, directly step on the brake and clutch to the end, quickly strike the fire, and then start according to the above steps.
In the end, the most important thing, whether it's the subject 2 exam or the daily driving, is your mood. Don't be too nervous, just keep in touch more every day. If it's because you feel that you don't have much time to practice in driving school, you can rent a home simulation learning car from Ai Xueche, put it at home for your own practice, and return it after you finish the exam, so it won't take up too much space and it's more convenient for you to practice.
what should I pay attention to in the subject 2 exam?
1. The basic elements that must be mastered Subject 2 must master three basic skills: controlling the clutch, watching according to the reference object and steering the wheel.
Hold the clutch steady, keep it slow but don't stop, especially when steering the wheel. Automatic transmission means stepping on the brakes. Skilled steering wheel and standardized action.
follow the principle of "call as many times as possible, call less and call back less, call back slowly, call back big, call back quickly". Have a certain sense of direction and distance, which is very important in reversing storage and lateral parking! When the car is driving slowly on the road, it is necessary to judge whether the car body is positive or not, and the approximate distance between the car body and the sideline.
Observe carefully, be good at using the rearview mirror, and be sure to hit the opening point accurately. 2, timely communication, maintain moderate tension, be good at finding problems in practice, and communicate with coaches or students in time if you don't understand anything, which is often easier to understand.
There is a process of driving practice. At first, you will be nervous, and then you will gradually relax. However, students should keep a certain degree of tension in the practice before the exam. 3, the simulation test found insufficient in advance. Many students thought that their foundation was solid enough and their psychological quality was excellent, so they did not participate in the pre-test simulation. In fact, it was a big mistake! The mock exam is to familiarize yourself with the atmosphere of the examination room and exam, so you don't have to be too nervous. If you find any problems, you still have the opportunity to correct them in time.
After the simulation, you can communicate with the coach and solve the problems. What should I pay attention to in the subject 2 exam? For details, please consult Xiexin Driving School.
。
Matters needing attention in the second exam
1. Be sure to adjust the seat and rearview mirror to the proper position you are used to. (Adjust the left rearview mirror to the proper position where you can easily see the left rear door handle and the left rear wheel. Adjust the right rearview mirror to the lowest position, and the driver can see that the right front handle is around the middle position of the right rearview mirror. Remember to fasten your seat belt.
2. Get into the good habit of turning on the turn signal (turn on the light whenever you go in or out).
3. Pay attention to the control of vehicle speed (mainly by stepping on the clutch, and if necessary, slightly step on the brake, but not on the parking). "Slow speed and fast direction" is the key point.
4. Except for the road sections between the examination areas of each project, you can stop and wait. Once you enter the examination area, you can't stop halfway during operation.
5. Be sure to listen to the voice prompts clearly and let the computer judge and confirm your operation (about 3 seconds) before making the next move. Don't be too hasty.
6. Pay special attention not to hit the wrong direction. "Look forward at the front of the car, look backward at the rear of the car, and hit whichever side you want." It is not recommended to hit the direction in the same place after parking (although no penalty points will be deducted). It is recommended that the front wheel of the car should be positive after parking.
What should I pay attention to when preparing for Subject 2
Matters needing attention in Subject 2: 1. Precautions for reversing into the warehouse: (1) The distance from the car to the starting position, when the car is offline, the car body should press the white line in front of the right side of the garage, but it should not exceed it.
(2) When reversing, pay attention to the line points and kill the direction. How to practice at ordinary times is still how to take the exam, and look at the library points from the rearview mirror. (3) After the car enters the garage, it must be straight back, and don't turn left and right.
2. Precautions for side parking: The distance between the car body and the edge of the garage and the distance between the car body and the garage should be well adjusted, and it should not be too close to the garage, and at least the rear wheels of the car should exceed the edge line of the garage. When you hit the direction, you should look at the line. 3. Precautions for turning at right angles: When the car reaches the corner, the steering wheel will be killed according to the speed.
You can stretch your head to see if the left rear wheel of your car can press the corner. If it can, you can turn back the steering wheel properly. 4. Precautions for fixed-point climbing and starting: (1) Turn right when the car goes uphill, and the speed should not be fast.
Generally, the right wheel of a car is 3cm away from the edge line. Control this distance.
(2) when you reach the specified position, the speed will be slower, so that you can find the time more accurately. 5. Precautions for curve driving: (1) After the car enters the curve, it should turn to a big bend.
(2) It's better to control the speed slowly and advance at a constant speed, and keep an eye on every corner, hit the direction quickly and return quickly.
Extended information: Examination contents of subject 2: According to Article 25 of the Regulations on the Application and Use of Motor Vehicle Driving License (Order No.123 of the Ministry of Public Security), the examination contents of subject 2 include: 1. Examination of large passenger cars, tractors, city buses, medium-sized buses and large trucks, fixed-point parking and starting on ramps, side parking, passing through unilateral bridge, curve driving, right-angle turning, passing through width-limited doors and passing through continuous roads.
2. Small cars, small automatic cars, small automatic passenger cars for the disabled and low-speed trucks are parked in the back of the car, parked and started at a fixed point on the ramp, parked sideways, driven in curves and turned at right angles; 3, three-wheeled vehicles, ordinary three-wheeled motorcycles, ordinary two-wheeled motorcycles and mopeds, stop and start on the ramp, and pass through unilateral bridge; Baidu Encyclopedia-Subject 2.
what should I pay attention to in the exam of subject 2?
Matters needing attention in the exam of subject 2:
1. Adjusting the rearview mirror
Adjusting the rearview mirror is the preparation work before the exam, which is known to all. However, there are still many students who forget or neglect to adjust the rearview mirror during the exam.
The items with high requirements for the rearview mirror include parking in reverse and side parking. There is no requirement for everyone to adjust the rearview mirror in the exam, but if you don't pay attention to looking at the rearview mirror or adjusting the rearview mirror when preparing, when you do parking in reverse or side parking, you will probably hang up directly, and you won't even know when you drive to the line! Because you didn't adjust the rearview mirror, you can't see the point, so it's as dangerous to do the exam as the blind walking at night! This is all caused by the fact that students only pay attention to practicing cars and don't pay attention to adjusting the mirror when practicing cars.
2. Clutch control
Clutch control plays an important role in the training of subject 2. The examination requirements of subject 2 don't say what kind of clutch the students can control to be qualified, but it is always inseparable from clutch control during the examination.
If the clutch is not well controlled, it will easily lead to flameout at the start (points will be deducted) and stop in the middle (unqualified directly); In the test items, the higher requirements for clutch operation are the fixed-point parking and starting on the ramp. The loose clutch is more or less prone to problems, or the flameout or slipping, which is really "increasing one point is too fat, and reducing one point is too thin." Shi zhifen is too white, Shi zhizhu is too red ",sometimes it really makes the students feel puzzled and want to cry!"
In addition, the bad clutch control has a great influence on the exam, but the speed can't be controlled. Please read on.
3. Adjustment of mentality
Examination mentality is definitely not the decisive factor that affects the examination, but the success or failure of the examination will definitely be affected by the examination mentality.
Here, students are encouraged to make more efforts in driving skills, study hard and practice hard, and improve their driving skills, which is the basis for passing the subject 2 exam. Because the technology is practiced at home, there is naturally confidence; There are problems in the exam. In the final analysis, you still have some exam items that are not firmly mastered, and your skills are not at home. Coupled with the tension, you finally failed in the exam.
4. Control of vehicle speed
Similarly, there is no clear test requirement for vehicle speed in Subject 2, and the test never says how fast or how slow to drive is qualified. However, if you want to pass the Subject 2 test successfully, the control of vehicle speed must be controlled from beginning to end. Control the speed well, and you will have a solid foundation for successfully passing the subject 2 exam. It can be seen how important the speed control is to the subject 2 exam.
The terrible thing is that some people don't realize this, or don't pay attention to the control of speed, and it's too late to regret it when the speed is too fast during the exam! If you want to control the speed and clutch well, you can't control it overnight, nor can you control it verbally. It takes a long time of skilled operation!
Precautions for Subject 2 Examination
Precautions for Subject 2 Examination of Driving School First, candidates must gather together on time with their ID cards (if they are late, they will be disqualified), and the staff led by the driving school will take them to the examination area.
(In order not to affect the examination time of candidates' next subject, please submit the listing and admission ticket to the driving school team leader for registration after the examination). Candidates are not allowed to smoke, make noise, be noisy, be naked, wear slippers, and are not allowed to answer the phone (the phone must be turned off).
- Previous article:Why were Shen Congwen and Wang Zengqi buried?
- Next article:Kindergarten outing banner
- Related articles
- What software is used to make dynamic posters-what software is used to design posters
- It’s suitable to say when you’re feeling depressed, like there’s only me in the world or there’s no me.
- Slogans for saving water in public places, and slogans for saving water in public places.
- What are the events in the Electrical and Electronic Skills Competition?
- What kind of protection does Meituan have for receiving orders?
- Model essay on summary of warning education activities (5 articles)
- Advertising language of new energy vehicles
- What exactly is China? How do you understand.
- Why can't minors sit in on the trial?
- Discussion and practice of Yuxi education and sports system focusing on "two transformations, one strength and one promotion"