Traffic regulations within the factory area

1. Common sense about traffic in the factory area

Common sense about traffic in the factory area 1. What are the traffic safety requirements in the factory area?

The traffic safety requirements in the factory area are as follows: (1) Smooth driving is strictly prohibited. Walk centrally on railways and highways.

When walking along the railway line, you should be 1.5m away from the railway track. When walking along the highway, you should walk on the sidewalk. When there is no sidewalk, keep to the right. When crossing the railway or highway, you must do "one stop, two looks, three confirmations, four pass". (1) Unrelated persons are not allowed to ride on locomotives, slag trucks, tank trucks and other vehicles at will.

(2) It is not allowed to jump, drill or climb from any part of slag, iron tank trucks and other vehicles. (3) It is strictly prohibited to rest, sleep or tow on railways, highways, rails, sleepers or vehicles.

(4) It is forbidden to approach the moving vehicle and drive in the same direction. When slag and iron tank trucks are reversed along the line, workers should stay out of the way to prevent burns caused by overflowing slag and iron tanks.

(5) Pedestrians and vehicles strictly abide by traffic signals and light signals. A green light indicates passage, a yellow light indicates slow movement, and a red light indicates no passage.

2. Road traffic speed limit standards within the factory area

Refer to "Road Traffic Signs and Markings" GB 5768-1999. This standard specifies the classification of traffic signs and markings, and stipulates Requirements for the design, manufacture, installation and construction of traffic signs and markings. This standard applies to signs and markings of facilities on highways, urban roads, and roads in mining areas, port areas, forest areas, fields (factories), etc.

Sharp left (or right) curve sign. Used to warn vehicle drivers to slow down. It is assumed that the calculated driving speed is less than 60km/h, the radius of the flat curve is equal to or less than the general minimum radius stipulated in the road technical standards, and the parking sight distance is less than the specified sight distance outside the required curve starting point, but it is not allowed to enter the adjacent circular curve Inside.

3. Who has a traffic safety management system in the factory?

Factory traffic management system 1. Purpose To regulate the movement of vehicles in the factory and prevent safety accidents caused by violations of traffic rules.

2. Scope of application: All motor vehicles entering the company's factory area and forklift, forklift, and crane drivers within the company. 3. Responsible persons: Security Department, Fleet, Safety Department, Sales Department, Equipment Department, Material Supply Department 4. Work Procedures 4.1 Management Organization (1) Traffic management in the factory area follows the principle of “whoever owns the car manages it”.

(2) The fleet is responsible for establishing a vehicle maintenance and repair system, strictly inspecting vehicle quality, conducting regular overhauls and maintenance, eliminating inspections and missed repairs, and doing a good job in annual vehicle inspections and other tasks. (3) The security department is responsible for the management of traffic and traffic accidents in the factory area.

(4) The units where various vehicles are located should formulate their own vehicle management rules in accordance with relevant national technical regulations. (5) Strictly implement the in-factory motor vehicle inspection and examination system, and the inspection and examination shall be carried out by the superior competent department.

(6) The motor vehicle must be in good condition and can only be driven after passing the inspection and issuing an inspection certificate. 4.2 Signals and signs (1) All kinds of vehicles are prohibited from parking on access roads, gates, curves, ramps, one-way streets, and intersections in the factory area.

(2) Obvious warning signs should be set up on restricted access roads and controlled roads in the factory area. (3) For road construction and the erection of strong structures across roads, in addition to obtaining the consent of the competent department, there must also be obvious signs. There must be signal lights at night. Temporary traffic control should be set up in areas with small construction sites where vehicles and pedestrians frequently come and go.

(4) Traffic roads in the factory area must have sufficient lighting. 4.3 Traffic lines (1) Traffic roads should be smooth and smooth. There should be sewers on the roadside and should be dredged regularly. It is strictly forbidden to discharge steam, smoke, oil, acid, alkali and other harmful substances onto the road surface. Ice and snow accumulated in winter should be removed in time.

(2) The company’s traffic department will divide the roads into: ① Free Road: All kinds of vehicles are allowed to pass. ② Restricted roads: Safety vehicles equipped with flame arresters and static electricity elimination devices are allowed to pass, and they can only pass after approval by the competent vehicle department.

③ Controlled road: It is a dedicated passage for fire trucks, ambulances, and engineering rescue vehicles. Other vehicles are prohibited from stopping. (3) It is strictly prohibited to accumulate materials on main roads and fire escapes, and to carry out operations on the road that obstruct traffic. Any temporary occupation or groundbreaking construction due to production needs must be approved by the leader in charge of safety.

(4) Materials stacked on both sides of the road should be 1 meter away from the roadside, and the stacking should be firm; when flowers and trees are planted on both sides of the traffic, the distance from the roadside should not be less than 1 meter; rope racks should be stretched across the road Its height shall not be less than 5 meters. (5) Crawler vehicles are not allowed to drive on cement roads and asphalt roads without taking road expansion measures.

4.4 Vehicle Driving (1) Motor vehicle drivers must pass professional training, be approved by the Enterprise Management Section, and be issued a factory driving license after being assessed by the Safety Technology Section before they can drive. (2) Drivers of motor vehicles for traffic in the factory area must be issued a special operation driver's license after passing professional training and assessment by the municipal labor department in accordance with the training and assessment regulations for special operations personnel.

(3) The driving speed of motor vehicles in the factory is not allowed to exceed 10 kilometers/hour. (4) Motor vehicles in the factory are prohibited from driving outside the factory.

4.5 Vehicle Loading Motor vehicle loading must comply with the following regulations: (1) Do not exceed the cargo capacity approved on the vehicle license. (2) Loading bulk powder or easy-to-drip items must be tightly sealed.

(3) Loading of hazardous chemicals should be carried out in accordance with relevant regulations. (4) Loaded items must comply with regulations and are not allowed to be over-length (the rear end is not allowed to exceed the body by 1 meter), over-width (both sides of the carriage are not allowed to exceed the body by 10 centimeters), over-height (the rear end is not allowed to exceed 4 meters from the ground), Overweight (allowable load capacity).

4.6 Bicycles, tricycles, motorcycles and other non-motorized vehicles are prohibited from driving in the factory area. 4.7 Measures for the management of outsiders (vehicles) In order to strengthen the orderly management of outsiders (vehicles) and ensure the company's normal and safe production, these measures are specially formulated.

(1) When outsiders enter the company boundary, the guard must inquire about the situation. Those who are being received by the unit must be contacted by phone and be led in by personnel from the reception unit. Otherwise, entry will not be allowed. Violators will be punished by the person on duty. 50 yuan/time. (2) Vehicles from outside units (except vehicles purchased by relevant departments and companies and products sold by ***) will not be allowed to enter without completing relevant procedures. Violators will be fined 50 yuan per time on duty.

(3) Vehicles of outsourced companies inside and outside the factory must be verified by the Security Department and Safety Technology Department. After approval by the relevant company leaders, the official seals of the two units must be stamped to apply for a pass (for other vehicles, please refer to this article). Only the guard is allowed to enter. Violators will be fined 50 yuan per time by the person on duty. (4) Before foreign construction workers enter the company boundary, the company's business department is responsible for notifying the Safety Technology Department to conduct safety education. After passing the assessment, the foreign workers will be issued entry and exit passes. The Safety Technology Department will register and file the personnel before the guard can allow entry.

The head of the department (section) who fails to comply with this provision will be fined 100 yuan. (5) The company's business department is responsible for the safety management of external construction workers within the company's boundaries. When signing an outsourcing agreement, there must be a clause clarifying safety responsibilities. Violators will be fined 100 yuan.

(6) Minors are prohibited from entering the company's factory. Violators will be held accountable not only for the parties involved, but also for the door guards, and the person on duty will be punished with a fine of 100 yuan. (7) Outsiders are not allowed to perform operations such as packaging and loading. They must follow the instructions of factory personnel and comply with relevant regulations.

(8) Anyone who violates any of these regulations will be punished according to the above provisions, and those who cause consequences will be investigated and dealt with step by step according to the responsible accident. 5. Supplementary Provisions This system is explained by the company's Security Department and Safety Department.

4. 100 common sense about traffic safety

1. Walking instructions

1. Pedestrians must walk on the sidewalk, and if there is no sidewalk, they must walk on the roadside;

2. Pedestrians are not allowed to chase or run on the road, nor are they allowed to suddenly turn and cross when a vehicle approaches;

3. Pedestrians are not allowed to chase or chase cars on the road

4. Children are not allowed to play or frolic on the road;

5. Preschool children must walk on the streets or highways. Be led by an adult;

2. Instructions for riding a car

1. It is not allowed to hail vehicles in the middle of the road;

2. A motor vehicle is not allowed to pass by while driving Any part of the body sticks out of the window; 3. When riding in the bus, you are not allowed to stand, and you are not allowed to eat in the bus;

4. Do not force people to get on or off the bus, get off first and then get on, and wait in line. , get on the bus in order; after getting off the bus, wait for the vehicle to drive away before walking. If you want to cross the road, be sure to do so safely;

5. Do not ride in overloaded vehicles or unloaded vehicles Vehicles with passenger license and sports license;

3. Cycling instructions

1. Children under the age of twelve are not allowed to ride bicycles or tricycles on the road;

2. Before turning, you must slow down, look back, extend your hand to indicate, and do not make sudden turns;

3. Do not leave your hands off the handlebars, and do not hold onto other vehicles or hold objects in your hands. ;

4. Vehicles are not allowed to run parallel to each other, chase each other or race in twists and turns;

5. Check the performance of the vehicle frequently, and do not ride if there is a problem with the bell, brake or other parts. , should be repaired in time;

6. It is not allowed to ride a bicycle with an umbrella, and it is not allowed to ride with a person;

7. It is not allowed to learn to ride a bicycle on the road;

< p> 8. Do not park on the roadway or compete with motor vehicles;

5. List 10 common sense of traffic safety

1. Take a public vehicle , we should abide by public order, pay attention to social ethics, and pay attention to traffic safety.

2. When crossing a road, choose a place with a crosswalk.

3. When crossing the road, you must obey the instructions of the traffic police; you must abide by the traffic rules, walk on green lights and stop on red lights.

4. When crossing the road, walk in a straight line and do not cross in a roundabout way; when there is no crosswalk, you should first look to the left, then to the right, and only cross the road after confirming that no motor vehicles are passing.

5. Pay attention to driving in summer. Drivers are prone to fatigue and dozing off. Therefore, be sure to rest before driving and do not drive forcefully.

6. When driving at night, the field of view is not as wide as during the day, and the safety factor is reduced. In addition, some drivers stay out of the car for too long, which may cause dizziness, blurred vision, lack of concentration, etc., leading to confusion on both sides of the truth. Misjudgment of the situation may lead to traffic accidents.

7. When encountering abnormal situations such as signal lights being interrupted due to power outages, traffic jams, road construction, etc., you should obey the instructions of the traffic police.

8. Observe traffic ethics, do not chase and fight on the highway, do not throw stones or debris at moving vehicles, and do not throw stones, bricks, or sharp objects on the highway.

9. Don’t talk on the phone when crossing the road. Talking on the phone distracts your attention and can easily cause traffic accidents.

10. Don’t read while walking. Reading while walking will distract your attention and may lead to traffic accidents.