How to protect the refined decoration products?

Fine decoration is the choice of more and more people, so what are the finished product protection measures in the process of fine decoration? Aifuwo, let me explain it to you one by one.

1. Protection measures for refined decoration products

1. 1 Provide training and education on finished product protection for all construction personnel entering the site, and establish the consciousness of finished product protection subjectively. Designate full-time personnel to be responsible for the protection of finished products, and establish an effective reward and punishment system.

1.2 Each professional type of work shall take professional protective measures for the professional construction, and the finished or semi-finished products shall go through the written handover formalities with relevant units. ?

1.3 the project department should strictly regulate the water and electricity consumption on site to avoid the damage of finished products caused by water leakage.

1.4 the project department must establish transportation channels, material storage yards and warehouses to prevent the damage to finished products caused by on-site transportation and stacking of materials.

1.5 If it is found that other specialties fail to protect finished products or the finished products are damaged during the construction, it shall be coordinated in time, and the project manager, supervisor, owner and relevant units shall be informed.

1.6 It is forbidden to scribble on finished and semi-finished products. If necessary, it should be marked in an orderly manner without affecting the finished product interface.

1.7 Establish a garbage transportation channel, close the garbage channel when conditions permit, and prohibit littering and throwing objects at high altitude.

1.8 according to the site conditions, temporary toilets should be built, or temporary sanitary facilities such as urinals should be set on balconies and terraces. Resolutely prohibit defecation at the scene.

2. Fine decoration construction protection measures for pre-construction finished products?

2. 1 Protection of civil finished products

2. 1. 1 During the construction of special projects department, if it is necessary to open holes and dig in civil walls, floors, structural beams and columns, it is necessary to contact the project management personnel of the supervisor and the employer, relevant units and design units in advance and obtain written approval before construction. Without permission, it is forbidden to open holes, slot and cut structural steel bars at will in civil structures. After obtaining written approval, the holes and grooves in the walls made of civil structures or other materials shall be marked according to the requirements of the drawings before construction.

Necessary special tools should be used in the construction. 2. 1.2 After the cement mortar screed-coat is completed, you shall not walk or trample on it within 24 hours. When the trolley is transported on the completed ground leveling layer, the scaffold lane should be laid first to prevent the leveling layer from being damaged. It is forbidden to mix mortar on the completed ground. ?

2. 1.3 When the construction equipment is erected on site, scaffolding should be used for separation to prevent oil pollution on the wall and ground. If there is pollution, it should be cleaned up in time. During construction operations such as welding and cutting, isolation measures should be taken to prevent damage to completed walls and floors. ?

2. 1.4 When building temporary warehouses or stacking materials on the construction site, isolation measures should be taken, and special protection should be given to the external corner parts such as walls, columns and stair treads of completed civil works. ?

2.3 Protection of water, electricity, heating and other supporting products.

2.3. 1 During the construction of the project department, if the decoration construction is affected by the completed parts of water, electricity, heating and other specialties, it shall notify the supervisor, the owner's project management personnel and relevant units in writing.

It can only be implemented after written approval. ? 2.3.2 Fine decoration construction should cooperate with each other and protect each other. It is forbidden to push, pull or step on the installed products, especially the insulated pipes and air ducts.

3. Breakdown protection measures for finely decorated products?

3. 1 Protection of decorative raw materials

3. 1. 1 After all the raw and auxiliary materials are accepted by the engineering department, the warehouse keeper of the project department is responsible for warehousing, completing warehousing procedures and marking them as required. It is forbidden to pile them together. Only qualified materials and finished products enter the finished product warehouse. The finished product warehouse administrator of the project department shall classify and clearly identify the warehousing materials. Material warehouse and finished products shall be managed according to specifications, and dust, mildew and fire prevention shall be well done. All materials should be covered and registered. ?

3. 1.2 All materials shall be stored with protective measures, and the bottom shall be leveled with standard wood.

Each layer must be separated by thin battens, and the maximum stacking of materials shall not exceed 10 layer; The glass must be stored vertically on a special support, and there is a separation paper between each glass. 3. 1.3 protective measures should be taken when transporting materials in the factory. Direct contact with iron parts and hardware is prohibited to avoid damaging materials.

3. 1.4 The material processing platform shall be laid with blankets in accordance with the regulations, paying attention to no sundries. It is forbidden to drag and collide materials on the platform, and all materials should be lifted vertically when moving. ?

3. 1.5 For processed materials or finished products and semi-finished products, all debris on the surfaces and cavities shall be removed, cleaned and a protective film shall be affixed to the surfaces of finished products. ?