The floor tiles laid at home are very slippery. What should I do?

Anti-skid liquid, the first treatment scheme for floor tiles that are too slippery at home

Nowadays, many manufacturers are really smart. They seize a pain point of people and then make corresponding products. This tile anti-slip liquid is a typical product in this field. Anti-skid, as we can know when we hear the name, can solve the problem that the floor tiles are too slippery. Therefore, we can use the anti-slip liquid of ceramic tiles for treatment.

Action principle of tile anti-slip liquid: It uses a high-permeability chemical synthetic material, which can penetrate into the interior of the tile surface, and then chemically react with some silicon in the tile to dissolve some silicon. Its purpose is to form some small holes on the surface of ceramic tiles, so as to solve the problem of anti-skid of ceramic tiles.

the second treatment scheme for the floor tiles in the home is too slippery.

The second treatment scheme is to lay the floor directly on the tiles. Everyone knows that the floor is far superior to the floor tile in anti-skid. So we can use the floor instead of the floor tile to solve the problem that the floor tile is too slippery. The method of laying floor tiles on the floor is actually very simple, because the floor tiles are very flat and there is no dust, so almost no treatment is needed.

the concrete steps of laying the floor on the floor tile: the first step is to clean the surface of the tile, and then lay the moisture-proof film. The second step is to lay the wooden floor directly on the moisture-proof film. Because wooden floors now have installation slots, it is ok to assemble them directly.

The third treatment scheme for the floor tiles at home is too slippery.

Finally, there is another treatment scheme, which is to directly lay carpets on the floor tiles. This method is the simplest and cheapest to operate, but it may affect the decoration effect of our home. When laying carpets on the floor tiles at home, everyone must pay attention to the fact that the floor tiles must be cleaned. In addition, I personally suggest that you choose the carpet with a plastic layer on the back, so that it can be effectively combined with the floor tiles and there will be no carpet sliding.

expanding information

choosing a well-known manufacturer can avoid many problems, but how to avoid replacing the package and confusing the real with the fake? First of all, the flatness of ceramic tiles is the first, otherwise it can't be paved with exquisite craftsmanship. Ceramic tiles can be broken into two pieces in different types when entering the site to see if there are any problems inside.

1. The appearance color should be uniform, and the surface glossiness and smoothness should be better (except for special processes). Especially, we should pay more attention to their glossiness when polishing floor tiles. The higher the glossiness, the more exquisite the polishing process and the higher the relative hardness, so that the water absorption is low and the wear resistance is higher.

2, the ability to prevent pollution is better. Drop one or two drops of ink or colored water on the surface of the tile, and wipe it off with a wet rag after half an hour. If there are obvious traces, it means that it is easy to seep. If there is basically no trace left, it proves that it has good antifouling ability.

3. The size deviation should not be too large. That is, when four bricks are put together, they should be neat and have no obvious dislocation. Products with dimensional error greater than .5MM and flatness greater than .1MM will not only increase the difficulty of construction, but also have poor effect after decoration and cannot be used in engineering.

4, water absorption should meet the requirements. The lower the water absorption rate, the higher the density of its products, and the less easy it is to penetrate. Generally, colored ceramic tiles are not more than 1%; Unglazed porcelain tiles (including polished tiles) shall not exceed .5%; Glazed porcelain brick is not more than 1%.

5. See if the quality of floor tiles is qualified. The quality of tile decoration is mainly determined by whether the joint height between bricks is greater than .5 mm, whether the flatness of the overall surface is greater than 2 mm within a 2-meter-long range, and whether the joint straightness exceeds 3 mm within a 5-meter-long range. Anything exceeding the above range is unqualified for decoration quality.

6. Listen to the sound of tiles: you can't see the internal quality of tiles by looking, but you can distinguish them by tapping.

the method is: hold up a tile in each hand, and tap the brick surface of another brick with a corner of one brick, so that the sound is crisp and loud, and it is cooked; If the dull one is poor, it means that there is double skin or crack in the brick. Double skin means that when the brick is formed, the air in the material is not exhausted, resulting in poor combination and internal crack between the materials, which can not be seen from the surface and can only be identified by listening to the sound.