How to modify the access control password?

Question 1: How to modify the access code of the glass door? There is no score of 5 in the manual (any setting of the controller must be carried out in the programming state).

(1). Enter the programming mode:

Press [*]+[6-digit programming password] and beep twice. The factory programming password is 990 10 1. The user must modify the programming password after enabling the access control equipment. If there is no programming instruction within 20 seconds, the system will automatically exit the programming state. )

(2). Modify the programming password:

Press [0]+[6-digit new programming password]+[Repeat 6-digit new programming password] twice; Indicates that the setting was successful.

Give it a try! If not, find the manufacturer who installed access control for you before! !

Question 2: How to modify the access password Press #, enter the system password 12345 or 123456, press 1 after entering, then enter 5 digits to modify the system password, and press 60+# to enter 8 digits of the card number+# to delete the single card.

Question 3: How to modify the password of this access control? 5 points 1. First, you must know the programming password. The default programming password should be 12345.

2. Modify the password to open the door:

1) enters the programming state:

Press * to enter the administrative password, then #.

2) Press 5 to enter the new four-digit password, press #, then enter the new four-digit password again, press #, and press * to save.

Note: The password is an arbitrary four-digit number.

Question 4: How to change the access control password Hello, I am glad to answer your question:

Password access control machine setting modification method 1

1. Initial password: the programming password is 9999, and the use password is 1234.

2. Enter the programming state: function setting (in the programming state). Door state monitoring needs to cooperate with door magnetic switch. After this function is turned on, it has the following two functions: first, if you forget to close the door after entering the correct password, the buzzer will beep to remind the user to close the door; Second, if the door is illegally opened, it will start the alarm signal output, and the buzzer will sound a warning. The factory sets this function to off.

3. Usage: You can open the door by reading a valid card under normal working conditions; If you need to read a card and add a password, enter the correct password within 10 second after reading the card to open the door; If the user forgets the password of the card, he needs to delete the card, add the card again and modify the password himself. If you forget the programming password, you can use the jumper switch "reset" on the motherboard to restore the factory settings. Before turning on the power supply, turn off the power supply and turn the jumper switch to the "ON" position. After the buzzer rings three times, turn the jumper switch back to the "OFF" position to restore the factory settings. Please turn off the power supply before installing the wiring, and do not operate with electricity! Under normal circumstances, the electric lock is connected from the power controller.

Password access control machine setting modification method 2

1. Enter the programming mode: press [*]+[6-digit programming password] and beep twice, (the red light flashes and the green light is always on. The factory programming password is 990 10 1. The user must modify the programming password after enabling the access control equipment. If there is no programming instruction within 20 seconds, the system will automatically exit the programming state. )

2. Modify the programming password: press [0]+[6-digit new programming password]+[Repeat 6-digit new programming password] twice; Indicates that the setting was successful.

3. Set the door opening mode: card or general password: press [1]+[0] twice; Card plus personal password: press [1]+[ 1] and beep twice;

4. Set the door opening time: press [2]+[TT] and beep twice; TT indicates the opening time in seconds, and TT = 03； if the unlocking time is 3 seconds;

5. Set/modify the universal door opening password: press [3]+[4-digit new universal door opening password] twice, and the original 4-digit universal door opening password will be overwritten; Press [3]+[0000] and beep twice to clear all "common passwords";

6. Forced recovery of the factory programming password: remove the controller, short-circuit the two feet of J2, and then release it (power-on). The controller will give a beep, and then two beeps, and the controller can be restored to the factory programming password.

I hope my answer is helpful to you. . .

Question 5: The entrance guard keeps ringing. How to modify the password The re-modification of the access password has no effect on the access card. All-in-one access control machine uses a common password. You can open the door by credit card or password by default.

Method for modif access control password setting

1. Initial password: # # for programming and * * * * for use;

2, enter the programming state:

3. Function setting (in programming state):

Door state monitoring needs to cooperate with door magnetic switch. When this function is turned on, it has the following two functions:

A. If you forget to close the door after entering the correct password, the buzzer will beep to remind the user to close the door;

B. If the door is illegally opened, an alarm signal will be output and the buzzer will sound to give an alarm. The factory sets this function to off.

Turn off this feature.

Read ten illegal cards or enter the wrong password four times in a row, and the system will be locked 10 minute.

After reading ten illegal cards or valid cards continuously, enter the wrong password four times in a row to start the alarm signal output.

5. How to use:

(1) Open the door after reading a valid card under normal working conditions;

(2) If you need to read a card and add a password, enter the correct password within 10 second after reading the card to open the door;

(3) If the user forgets the password of the card, he needs to delete the card, add it again, and then modify the password himself;

(4) If you forget the programming password, you can use the jumper switch "reset" on the motherboard to restore the factory settings. Before turning on the power supply, turn off the power supply and turn the jumper switch to the "ON" position. After the buzzer rings three times, turn the jumper switch back to the "OFF" position to restore the factory settings.

1. Please turn off the power before installing the wiring, and do not operate with electricity.

2. Under normal circumstances, the electric lock is connected from the power controller.

share

Question 6: Ask for help: As shown in the figure, how to modify the common password of access control? 10. If you haven't changed your initial password, please try the following picture.

Question 7: How to change the password of this access lock? Do you only know the password now (it is 4 digits)? I want to reset Carmen's password! This is a comprehensive access control machine, there is no software, you look for instructions, manufacturers are different. If you can't find it, just text me and I'll find one for you.

Question 8: How to change the password 88 10C after the password of access control programming is changed?

operation instruction

I. Product introduction:

This induction card access controller is specially designed for various electronic door locks and security systems. This is one of the most advanced access control systems in modern times. It uses the latest central processing unit (CPU) and large-capacity storage chip, and all data will not be lost due to power failure; Adopt the latest technology, powerful, there are three ways to open the door: induction card, induction card plus password and pure password.

Perfect door state monitoring, output alarm, anti-disassembly, induction card, password combination and other security measures to make users safer; Powerful functions such as door opening button, doorbell, normally open or normally closed can make users more convenient.

This product provides a safe and automatic access control mode, and is an ideal equipment for business organizations, offices, factories, houses, communities and other places.

Second, the technical parameters:

Serial number item index

1 working power supply DC: voltage 12V 10% current >:

Question 9: How to modify this electronic access control password? 100 min CR-3 105A access control integrated machine working power supply: DC+ 12V static current: 50mA ambient temperature; -10℃-55℃ relative humIDity: 20%-90% RH identification frequency: id type 125KHZ(EM or compatible card). IC type 13.56MHZ(MF 1 or compatible card) Door opening mode: card or universal password programming mode: key valid card: 1000, appearance size: 15mm*76mm* 22mm universal password: 1 card reading. 2CM IC type 3-8CM signal output: relay output/level output button interface: 65433 WIEGAND26 format valid card personal password: 0000 unlock detection door magnetic state: turn off the function of modifying personal password: turn off # key +252005 (default programming password): enter programming mode 1+ 1: card plus password open mode. : Card or password open mode 2: Set lock time 3: Modify universal password (key 5678 opens the door) 4+0: Turn off tamper alarm 4+ 1. 7+3-digit code /7+ induction card: delete valid card 6+0: valid instruction to unlock (detect door magnetic state when unlocking) 6+ 1: valid instruction+door magnetic closing (multi-door interlocking or anti-stalking) 8+0: door magnetic alarm function 8+ 1: door magnetic alarm function 82+TT (.

Question 10: How to modify the password of the access control integrated machine? Every company's all-in-one settings are different. It's too easy for you. It's like a fairy coming down to earth. It is easy to change the model after reporting.