Can it be used in the sea shed in Anjie pigeon?

One: Installation: →→→→ ① Install the mobile phone card → On the back of the pigeon clock host (there is a card that reads: "Thank you for choosing Anjie pigeon racing timing system". The card was tied to a movable bracket, which was forcibly opened. There is a small cover under it. Open the lid and you will see a small slot for putting your mobile phone card. There is a metal plate with a small arrow on it. You can open the metal plate by gently pressing it in the direction indicated by the arrow. )

② Connect the scanning plate with the pigeon bell → There are four holes under the small head of the pigeon bell, and insert the crystal head of the pigeon bell into any hole until it clicks.

③ Turn on the power supply → Plug in the voltage regulator first, and then connect the voltage regulator to the pigeon clock. At this time, images and sounds will appear on the pigeon clock. The connection was successful.

2. Settings: → ① pigeon clock IP address settings (press the "Return" key, and when the "① Competition Status" screen appears, press the "0" key, and "Please enter the password" will appear. At this time, the cursor flashes. Please enter "0903 16" and press the "OK" key, and "Password entered correctly" will be displayed. When the cursor falls on "⑤GPRS Settings", press the "OK" key to enter "⑤ GPRS parameter display". Press "OK" to display "Equipment Code: * * *". This is the password number of your pigeon clock, which is consistent with the number on your chassis. In this diagram, the last line should show "223.004". * ".Please press the" Back "key, then press" Left ",select" ②GPRS parameter setting "with the cursor, and press" OK ". At this moment, a cursor is flashing. Please enter "223.004.2 16.032" and press "OK". This step is completed.

② SMS Settings (press "Return" and then "↓", select "⑤ SMS Settings" (or press "6" directly), press "OK" to enter "① SMS Center Settings" and press "OK". At this point, SMS Center is enabled and a series of numbers are displayed. With the cursor on "① SMS Center Number", press "OK". And the cursor keeps flashing, please press the ↓ key to move the cursor to the fourth word "1", press the "3" key to change "1" to "3", and press the "OK" key. After a few seconds, the pigeon bell will return to the "① SMS Center Settings" screen. At this time, please enter the mobile phone number you use to receive SMS. Note that the card number entered here is not the card number inserted in the pigeon clock, but the card number you use to read the message. You don't need to enter the card number of pigeon clock, but this card must be a mobile or Unicom card, and the telecom card cannot be used. When finished, press the "OK" button, then press the "Return" button twice, and the screen will return to "① Competition Status". Through the above two steps, your setup is complete.

Three: Bring an electronic ring: → First _ bring a pigeon, take out an electronic ring, press the left key and select "three foot ring matching", or directly press the "three" key and press "OK". At this time, the cursor is on "① Footring Matching Item" and press "OK", and the screen will appear: "① Footring: ② Feather. Enter the anklet number of your newly arrived racing pigeon into the pigeon clock. At this time, it should be noted that first enter the anklet number, the year on your racing pigeon anklet, and then enter the provincial code on the anklet, which is "24" in our province. Enter what your racing pigeon is, and finally enter the anklet number you often say. Please press the "OK" button above, and the screen of "Feather Color: ① White ② Gray ③ Black" will appear. At this point, please press the "↓" key until a note with the same color as your racing pigeon appears, and then press the "OK" key. At this time, the picture of "eye sand: ① yellow girl ② sand girl ③ cow girl" will appear again. Please press the "↓" key until you find the pigeon eye with you. At this time, you are required to scan the electronic ring you have prepared on the scanning board and take it to the scanning board. The pigeon bell will make a "drip" sound, and the pigeon bell will prompt "match". Now you must put this electronic ring on the pigeon's foot, and you can't take it with you! ! If you want to continue wearing the electronic ring, press the "OK" key and repeat the above operation.

Four: Enter the training and fly: → After you complete the above steps, the entered racing pigeon information will be permanently stored in the racing pigeon clock (you can delete one racing pigeon or all of them, which will be taught below). At this time, please turn off the power for a few seconds, then turn on the power to enter the training release. After each training flight, you only need to turn off the pigeon clock for a few seconds before the pigeon is released, and then turn on the power in your pigeon clock. You can play it again and record it again. After your pigeons come back and pass the scanning board, a few seconds, sometimes dozens of seconds, your homing information will be sent to your mobile phone. That's great. Please use it quickly if you don't believe me. Then you will find that this pigeon clock is very scientific-really wonderful!